Add sh7372 Core Standby sleep mode support and tie it
in with the shared SH-Mobile ARM suspend code.

The Core Standby mode is the lightest sh7372-specific
sleep mode, cutting power to the ARM core excluding the
L2 cache. Any interrupt source can be used for wakeups.

The low level portion of this code is based on the
TI OMAP sleep code in sleep34xx.S, thanks to them.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Use soc_camera_platform helper functions to dynamically manage the
camera device.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch reverts "ARM: mach-shmobile: sh7372 SDHI vector merge" and
supplies 3 IRQ resources for each SDHI block.

Some blocks have a 4th IRQ, but this is used for DRM feathres
that I do not have access tot he documentation for and are almost
certainly tainted by licensing issues. So the 4th IRQ is not
hooked-up even if it exists.

Cc: Chris Ball <cjb@laptop.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The PLLC2 clock on AP4 systems does not need to run constantly to be
able to use HDMI. The HDMI hotplug interrupt works without the PLL
too, after which all the necessary clocks will be turned on by the
runtime PM.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add DMA mode support for the MMCIF controller on mackerel.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Remember to also check for the CONFIG_MMC_SH_MMCIF_MODULE option
for the case of a modular MMCIF driver.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

If several boards are enabled in the kernel configuration,
hdmi_init_pm_clock() functions from board-ap4evb.c and board-mackerel.c
will run on any of them. Prevent this by calling these functions from the
.init_machine() callback instead of using device_initcall().
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Magnus Damm <damm@opensource.se>
Tested-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Convert to the new function names. Automated with coccinelle.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

SDHI registers occupy only a 0x100 byte large window, not 0x200 byte.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Cameras are currently broken on ARM sh-mobile platforms. They need a
suitable coherent DMA mask.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Use GPIO_PORT31 to control the backlight on the Mackerel board.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

mackerel WVGA LCDC panel expect 33.3MHz for dot-clock,
but current dot-clock was 50.0MHz.
This patch modify clock divider value.
Signed-off-by: NMakoto Ueda <makoto.ueda.ub@renesas.com>
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Current format selection of FSI-codecs depended on platform information for FSI,
and chip default settings for codecs. It is not understandable/formal method.
This patch modify FSI and FSI-codecs to use snd_soc_dai_set_fmt.

But FSI can use I2S/PCM and SPDIF format today.
It can be selected to I2S/PCM by snd_soc_dai_set_fmt, but can not select SPDIF.
So, this patch change FSI platform information to have DAI/SPDIF mode.

If platform selects DAI mode (default),
FSI-codecs can select I2S/PCM by snd_soc_dai_set_fmt,
and if it is SPDIF mode, FSI become SPDIF format.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch add platform_device_id which can control
PortA/PortB for FSI2-HDMI from platform data.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch add snd_soc_dai_ops :: set_fmt to FSI driver and
select master/slave clock mode by snd_soc_dai_set_fmt on
fsi-xxx.c instead of platform infomation code.
This patch remove fsi_is_master function which is no longer needed.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

* Pins 2 and 4 of switch 33 are documented as don't care on the PCB,
  my testing seems to confirm this.

* I have been unable to do anything sensible with S1 set to on.
  Am I missing something with regards to MMC1?

* Clarify which driver is needed for each switch setting.

* Should the AP4 board code be updated to allow the
  SHDI driver to access SHDI1 as the mackerel code does?
Signed-off-by: NSimon Horman <horms@verge.net.au>
Acked-by: NYusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The Card Detect GPIOs used on AP4EVB and Mackerel are
alwayws valid, so kill off the unused !gpio_is_valid()
case.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Enable SDIO IRQ support for the Mackerel board.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NTony SIM <chinyeow.sim.xt@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NYusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Break-out INTC specific IRQ demux code from the file
entry-macro-intc.S and register during run-time.

Covers sh7367, sh7377 and sh7372.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add VGA camera support to the Mackerel board
using soc_camera_platform.

The VGA camera module is hooked up using the
8-bit CEU bus, and it is constantly bursting
out frames in fixed video mode setting. The
camera module does not allow any I2C control.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NYusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

v2
 Add comment of J22 and OCR field.
Signed-off-by: NYusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NYusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch maps key0/key1/key2/key3 as HOME/MENU/BACK/POWER buttons
on mackerel board.
Signed-off-by: NTony SIM <chinyeow.sim.xt@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NTony SIM <chinyeow.sim.xt@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

you can control it by
echo 0 > /sys/class/leds/led0/brightness
echo 1 > /sys/class/leds/led0/brightness
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

RGB24 bus needs 18-23 pin
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>