This change updates the ixgbe driver to use __netdev_pick_tx instead of
the current logic it is using to select a queue.  The main result of this
change is that ixgbe can now fully support XPS, and in the case of non-FCoE
enabled configs it means we don't need to have our own ndo_select_queue.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Reviewed-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change adds support for ixgbe to configure the XPS queue mapping on
load.  The result of this change is that on open we will now be resetting
the number of Tx queues, and then setting the default configuration for XPS
based on if ATR is enabled or disabled.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Reviewed-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Instead of adjusting the FCoE and Flow director limits based on the number
of CPUs we can define them much sooner.  This allows the user to come
through later and adjust them once we have updated the code to support the
set_channels ethtool operation.

I am still allowing for FCoE and RSS queues to be separated if the number
queues is less than the number of CPUs.  This essentially treats the two
groupings like they are two separate traffic classes.

In addition I am changing the initialization to use the MAX_TX/RX_QUEUES
defines instead of trying to compute the value as it will be possible in
upcoming patches for the user to request the maximum number of queues.

I have also updated things so that the upper limit on queues is exactly 63
instead of allowing it to go up to 64.  The reason for this change is to
address the fact thqt the driver only supports up to 63 queue vectors since
the hardware supports 64 MSI-X vectors, but one must be reserved for "other"
causes.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

On several machines with i350 adapters the ethtool offline self-test sometimes
fails. This happens because link auto negotiation may take longer than the
timeout of 4 seconds. Increasing the timeout by 1 seconds resolves the issue.

Output from a failing i350 offline self-test:
while [ 1 ]; do ethtool -t eth2 offline; done
The test result is PASS
The test extra info:
Register test  (offline)         0
Eeprom test    (offline)         0
Interrupt test (offline)         0
Loopback test  (offline)         0
Link test   (on/offline)         0

The test result is FAIL
The test extra info:
Register test  (offline)         0
Eeprom test    (offline)         0
Interrupt test (offline)         0
Loopback test  (offline)         0
Link test   (on/offline)         1

The test result is PASS
The test extra info:
Register test  (offline)         0
Eeprom test    (offline)         0
Interrupt test (offline)         0
Loopback test  (offline)         0
Link test   (on/offline)         0
Signed-off-by: NStefan Assmann <sassmann@kpanic.de>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to address several race issues that become possible
because next_to_watch could possibly be set to a value that shows that the
descriptor is done when it is not.  In order to correct that we instead make
next_to_watch a pointer that is set to NULL during cleanup, and set to the
eop_desc after the descriptor rings have been written.

To enforce proper ordering the next_to_watch pointer is not set until after
a wmb writing the values to the last descriptor in a transmit.  In order to
guarantee that the descriptor is not read until after the eop_desc we use the
read_barrier_depends which is only really necessary on the alpha architecture.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Acked-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Current e1000e driver doesn't tell nothing when Link Speed is downgraded due to
SmartSpeed.  As a result, users suspect that there is something wrong with
NIC.  If the cause of it is SmartSpeed, there is no means to replace NIC. This
patch make e1000e notify users that SmartSpeed worked.
Signed-off-by: NKoki Sanagi <sanagi.koki@jp.fujitsu.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fixes whitespace issues, such as lines exceeding 80 chars, needless blank
lines and the use of spaces where tabs are needed.  In addition, fix
multi-line comments to align with the networking standard.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>

This patch reshuffles the switch/case structure of the flag assignment to
allow for the flags to be set for each MAC type separately. This is needed
for new HW that does not have feature parity with older HW.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NJack Morgan <jack.morgan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch simplifies igb_get_invariants function by moving all implemented
function pointers in this function to individual separate functions,
based on their functionalities, this would make debugging much easier.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch initializes MAC function pointers for device configuration.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch initializes NVM function pointers for device configuration.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch initializes PHY function pointers for device configuration.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

After reviewing the igb and ixgbe code I realized there are a few issues in
how the code is structured.  Specifically we are not checking the size of the
buffers being used in transmits and we are not using the same value to
determine when to stop or start a Tx queue.  As such the code is prone to be
buggy.

This patch makes it so that we have one value DESC_NEEDED that we will use for
starting and stopping the queue.  In addition we will check the size of
buffers being used when setting up a transmit so as to avoid a possible buffer
overrun if we were to receive a frame with a block of data larger than 32K in
skb->data.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch correctly resolves the sparse warnings found with this
function.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes the allocation function in igb_get_i2c_client to use
GFP_ATOMIC instead of GFP_KERNEL because we have a spinlock.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes an issue where we check for irq's disabled then exit after
explicitly disabling them with spin_lock_irqsave.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <arron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change makes it so that we can enable the use of build_skb for cases
where jumbo frames are disabled.  The advantage to this is that we do not
have to perform a memcpy to populate the header and as a result we see a
significant performance improvement.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When a user adds bridge neighbors, allow him to specify VLAN id.
If the VLAN id is not specified, the neighbor will be added
for VLANs currently in the ports filter list.  If no VLANs are
configured on the port, we use vlan 0 and only add 1 entry.
Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
Acked-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using the RTM_GETLINK dump the vlan filter list of a given
bridge port.  The information depends on setting the filter
flag similar to how nic VF info is dumped.
Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The original fix that was applied for setting gso_type required more change
than necessary because it was assumed ixgbe does RSC on IPv6 frames and this
is not correct.  RSC is only supported with IPv4/TCP frames only.  As such we
can simplify the fix and avoid the unnecessary move of eth_type_trans.

The previous patch "ixgbe: fix gso type" and this patch reduce the entire fix
to one line that sets gso_type to TCPV4 if the frame is RSC.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ixgbe set gso_size but not gso_type. This leads to
crashes in macvtap.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

alloc failures already get standardized OOM
messages and a dump_stack.

For the affected mallocs around these OOM messages:

Converted kmallocs with multiplies to kmalloc_array.
Converted a kmalloc/memcpy to kmemdup.
Removed now unused stack variables.
Removed unnecessary parentheses.
Neatened alignment.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NArend van Spriel <arend@broadcom.com>
Acked-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Acked-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change corrects the fact that we were using 1522 to test for the
max frame size in ixgbe_change_mtu and 1518 in ixgbe_set_vf_lpe.  The
difference was the addition of VLAN_HLEN which we only need to add in the case
of computing a buffer size, but not a filter size.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NSibai Li <Sibai.li@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The rmb in the Tx cleanup path is a much stronger barrier than we really need.
All that is really needed is a read_barrier_depends since the location of the
EOP descriptor is dependent on the eop_desc value.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch removes the rval variable returns from function and replaces
them with direct returns in ixgbe_dcbnl_getnumtcs. It also changes how
ixgbe_gstrings_test is copied into data with memcpy in ixgbe_get_strings
because "*ixgbe_gstrings_test too small (32 vs 160)".
Signed-off-by: NJosh Hay <joshua.a.hay@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds a default case which goes to the next loop iteration
in the case where p is not set, preventing p from being dereferenced.
Signed-off-by: NJosh Hay <joshua.a.hay@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds functions needed for reading SFF-8472 diagnostic data
from SFP modules.

Based on original patch from Aurélien Guillaume <footplus@gmail.com>

CC: Aurélien Guillaume <footplus@gmail.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Resolve the following strict checkpatch checks:
CHECK:BRACES: Blank lines aren't necessary after an open brace '{'
CHECK:BRACES: Blank lines aren't necessary before a close brace '}'
CHECK:BRACES: braces {} should be used on all arms of this statement
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There are enough register offsets to warrant being in their own header
file, and doing so logically separates them from other header file content.
They have been converted from an enumerated data type to #defines as is
done in all the other Intel wired ethernet drivers.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move #defines, function prototypes and data types which are applicable to
all/most devices supported by the driver but are specific to the
manageability component of each device to the new manage.h header file.
These #defines, function prototypes and data types can be used by other
files in the driver and moving them to the manageability-specific file
makes it clearer to which component they are applicable.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move #defines and function prototypes which are applicable to all/most
devices supported by the driver and are specific to the NVM component of
each device to the new nvm.h header file.  These #defines and function
prototypes can be used by other files in the driver and moving them to the
NVM-specific file makes it clearer to which component they are applicable.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move #defines and function prototypes which are applicable to all/most
devices supported by the driver and are specific to the PHY component of
each device to the new phy.h header file.  These function prototypes can be
used by other files in the driver and moving them to the PHY-specific file
makes it clearer to which component they are applicable.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move prototypes for functions which are applicable to all/most devices
supported by the driver and are specific to the MAC component of each
device to the new mac.h header file.  These function prototypes can be used
by other files in the driver and moving them to the MAC-specific file makes
it clearer to which component they are applicable.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move #defines and function prototypes specific to the ICH/PCH family of
devices (ICH8/82562, ICH8/82566, ICH8/82567, ICH9/82562, ICH9/82566,
ICH9/82567, ICH10/82567, 82577, 82578, 82579, I217, I218) to the new
ich8lan.h header file (the convention for Intel wired ethernet drivers is
to use the name of the first device in the family for related file and
function names).  These defines and function prototypes can be used by
other files in the driver and moving them to the ICH/PCH-family-specific
file makes it clearer to which devices they are applicable.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move #defines specific to the ESB2/82563 family of devices to the new
80003es2lan.h header file.  These defines can be used by other files in the
driver and moving them to the 80003es2lan-family-specific file makes it
clearer to which devices they are applicable.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move #defines and function prototypes specific to the 8257x family of
devices (82571, 82572, 82573, 82574, 82583) to the new 82571.h header file
(the convention for Intel wired ethernet drivers is to use the name of the
first device in the family for related file and function names).  These
defines and function prototypes can be used by other files in the driver
and moving them to the 8257x-family-specific file makes it clearer to which
devices they are applicable.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

alloc failures already get standardized OOM
messages and a dump_stack.

Convert kzalloc's with multiplies to kcalloc.
Convert kmalloc's with multiplies to kmalloc_array.
Fix a few whitespace defects.
Convert a constant 6 to ETH_ALEN.
Use parentheses around sizeof.
Convert vmalloc/memset to vzalloc.
Remove now unused size variables.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For standard IEEE MII-compatible transceivers, the kernel has generic
register and bit definitions.  Use those instead of redundant local
defines.

Do not replace references of MII_CR_SPEED_10 with BMCR_SPEED10 (0x0000)
when it is not necessary (i.e. when it is bitwise OR'ed with another
value).

Some whitespace issues in the surrounding context of the above changes are
also cleaned up.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove the unused parameter when possible, otherwise use __always_unused
attribute.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>