- 08 11月, 2017 2 次提交
-
-
由 Nogah Frankel 提交于
Add support for ndo_setup_tc with enum tc_setup_type value of TC_SETUP_RED. This call sets RED qdisc on a traffic class. This patch supports RED qdisc only as a root qdisc and set in on the default tclass. It can be set with or without ECN. Signed-off-by: NYuval Mintz <yuvalm@mellanox.com> Signed-off-by: NNogah Frankel <nogahf@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Nogah Frankel 提交于
This patch adds 2 new registers: - Congestion WRED ECN TClass Profile Register [CWTP] - Congestion WRED ECN TClass and Pool Mapping Register [CWTPM] These registers would later be needed to offload RED-related functionality to the HW. Signed-off-by: NYuval Mintz <yuvalm@mellanox.com> Signed-off-by: NNogah Frankel <nogahf@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 04 11月, 2017 16 次提交
-
-
由 Petr Machata 提交于
When the bound device of a tunnel device is down, encapsulated packets are not egressed anymore, but tunnel decap still works. Extend mlxsw_sp_nexthop_rif_update() to take IFF_UP into consideration when deciding whether a given next hop should be offloaded. Because the new logic was added to mlxsw_sp_nexthop_rif_update(), this fixes the case where a newly-added tunnel has a down bound device, which would previously be fully offloaded. Now the down state of the bound device is noted and next hops forwarding to such tunnel are not offloaded. In addition to that, notice NETDEV_UP and NETDEV_DOWN of a bound device to force refresh of tunnel encap route offloads. Signed-off-by: NPetr Machata <petrm@mellanox.com> Reviewed-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Petr Machata 提交于
When a bound device of an IP-in-IP tunnel changes, such as through 'ip tunnel change name $name dev $dev', the loopback backing the tunnel needs to be recreated. Signed-off-by: NPetr Machata <petrm@mellanox.com> Reviewed-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Petr Machata 提交于
Changes to L3 tunnel netdevices (through `ip tunnel change' as well as `ip link set') lead to NETDEV_CHANGE being generated on the tunnel device. Because what is relevant for the tunnel in question depends on the tunnel type, handling of the event is dispatched to the IPIP module through a newly-added interface mlxsw_sp_ipip_ops.ol_netdev_change(). IPIP tunnels now remember the last set of tunnel parameters in struct mlxsw_sp_ipip_entry.parms, and use it to figure out what exactly has changed. Signed-off-by: NPetr Machata <petrm@mellanox.com> Reviewed-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Petr Machata 提交于
When a bound device of a tunnel netdevice changes VRF, the loopback RIF that backs the tunnel needs to be updated and existing encapsulating routes need to be refreshed. Note that several tunnels can share the same bound device, in which case all the impacted tunnels need to be updated. Signed-off-by: NPetr Machata <petrm@mellanox.com> Reviewed-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Petr Machata 提交于
The approach for offloading IP tunnels implemented currently by mlxsw doesn't allow two tunnels that have the same local IP address in the same (underlay) VRF. Previously, offloads were introduced on demand as encap routes were formed. When such a route was created that would cause offload of a conflicting tunnel, mlxsw_sp_ipip_entry_create() would detect it and return -EEXIST, which would propagate up and cause FIB abort. Now however IPIP entries are created as soon as an offloadable netdevice is created, and the failure prevents creation of such device. Furthermore, if the driver is installed at the point where such conflicting tunnels exist, the failure actually prevents successful modprobe. Furthermore, follow-up patches implement handling of NETDEV_CHANGE due to the local address change. However, NETDEV_CHANGE can't be vetoed. The failure merely means that the offloads weren't updated, but the change in Linux configuration is not rolled back. It is thus desirable to have a robust way of handling these conflicts, which can later be reused for handling NETDEV_CHANGE as well. To fix this, when a conflicting tunnel is created, instead of failing, simply pull the old tunnel to slow path and reject offloading the new one. Introduce two functions: mlxsw_sp_ipip_entry_demote_tunnel() and mlxsw_sp_ipip_demote_tunnel_by_saddr() to handle this. Make them both public, because they will be useful later on in this patchset. Signed-off-by: NPetr Machata <petrm@mellanox.com> Reviewed-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Petr Machata 提交于
When trying to determine whether there are other offloaded tunnels with the same local address, mlxsw_sp_ipip_entry_create() should look for a tunnel with matching UL protocol, matching saddr, in the same VRF. However instead of taking into account the UL protocol of the tunnel netdevice (which mlxsw_sp_ipip_entry_saddr_matches() then compares to the UL protocol of inspected IPIP entry), it deduces the UL protocol from the inspected IPIP entry (and that's compared to itself). This is currently immaterial, because only one tunnel type is offloaded, and therefore the UL protocol always matches, but introducing support for a tunnel with IPv6 underlay would uncover this error. Signed-off-by: NPetr Machata <petrm@mellanox.com> Reviewed-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Petr Machata 提交于
The work that needs to be done to update HW configuration in response to changes is similar to what __mlxsw_sp_ipip_entry_update_tunnel() already does, but with a number of twists: each change requires a different subset of things to happen. Extend the function to support all these uses, and allow finely-grained configuration of what should happen at each call through a suite of function arguments. Publish the updated function to allow use from the spectrum_ipip module. Signed-off-by: NPetr Machata <petrm@mellanox.com> Reviewed-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Petr Machata 提交于
The work that's done by mlxsw_sp_netdevice_ipip_ol_vrf_event() is a good basis for a more versatile function that would take care of all sorts of tunnel updates requests: __mlxsw_sp_ipip_entry_update_tunnel(). Extract that function. Factor out a helper mlxsw_sp_ipip_entry_ol_lb_update() as well. Signed-off-by: NPetr Machata <petrm@mellanox.com> Reviewed-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Petr Machata 提交于
The function mlxsw_sp_rif_create() takes an extack parameter. So far, for creation of loopback interfaces, NULL was passed. For some events however the extack can be extracted and passed along. So do that for NETDEV_CHANGEUPPER handler. Use the opportunity to update the type of info argument that mlxsw_sp_netdevice_ipip_ol_event() takes. Follow-up patches will introduce handling of more changes, and some of them carry an extack as well, but in an info structure of a different type. Though not strictly erroneous (the pointer could be cast whichever way), it makes no sense to pretend the value is always of a certain type, when in fact it isn't. So change the prototype of the above-mentioned function as well. Signed-off-by: NPetr Machata <petrm@mellanox.com> Reviewed-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Petr Machata 提交于
The piece of logic to promote decap route, if any, is useful for generic tunnel updates, not just for handling of NETDEV_UP events on tunnel interfaces. Extract it to a separate function. Signed-off-by: NPetr Machata <petrm@mellanox.com> Reviewed-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Petr Machata 提交于
This function only ever returns 0, so don't pretend it returns anything useful and just make it void. Signed-off-by: NPetr Machata <petrm@mellanox.com> Reviewed-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Petr Machata 提交于
Signed-off-by: NPetr Machata <petrm@mellanox.com> Reviewed-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Petr Machata 提交于
To implement NETDEV_CHANGE notifications on IP-in-IP tunnels, the handler needs to figure out what actually changed, to understand how exactly to update the offloads. It will do so by storing struct ip_tunnel_parm with previous configuration, and comparing that to the new version. To facilitate these comparisons, extract the code that operates on struct ip_tunnel_parm from the existing accessor functions, and make those a thin wrapper that extracts tunnel parameters and dispatches. Signed-off-by: NPetr Machata <petrm@mellanox.com> Reviewed-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Petr Machata 提交于
These functions ideologically belong to the IPIP module, and some follow-up work will benefit from their presence there. Signed-off-by: NPetr Machata <petrm@mellanox.com> Reviewed-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Petr Machata 提交于
Some of the code down the road needs this logic as well. Signed-off-by: NPetr Machata <petrm@mellanox.com> Reviewed-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Petr Machata 提交于
To distinguish between events related to tunnel device itself and its bound device, rename a number of functions related to handling tunneling netdevice events to include _ol_ (for "overlay") in the name. That leaves room in the namespace for underlay-related functions, which would have _ul_ in the name. Signed-off-by: NPetr Machata <petrm@mellanox.com> Reviewed-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 03 11月, 2017 5 次提交
-
-
由 Ido Schimmel 提交于
Make sure the device and the kernel are performing the multipath hash according to the same parameters by updating the device whenever the relevant netevent is generated. Signed-off-by: NIdo Schimmel <idosch@mellanox.com> Reviewed-by: NPetr Machata <petrm@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ido Schimmel 提交于
Up until now we used the hardware's defaults for multipath hash computation. This patch aligns the hardware's multipath parameters with the kernel's. For IPv4 packets, the parameters are determined according to the 'fib_multipath_hash_policy' sysctl during module initialization. In case L3-mode is requested, only the source and destination IP addresses are used. There is no special handling of ICMP error packets. In case L4-mode is requested, a 5-tuple is used: source and destination IP addresses, source and destination ports and IP protocol. Note that the layer 4 fields are not considered for fragmented packets. For IPv6 packets, the source and destination IP addresses are used, as well as the flow label and the next header fields. Signed-off-by: NIdo Schimmel <idosch@mellanox.com> Reviewed-by: NPetr Machata <petrm@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ido Schimmel 提交于
The RECRv2 register is used for setting up the router's ECMP hash configuration. Signed-off-by: NIdo Schimmel <idosch@mellanox.com> Reviewed-by: NPetr Machata <petrm@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ido Schimmel 提交于
The struct containing the work item queued from the netevent handler is named after the only event it is currently used for, which is neighbour updates. Use a more appropriate name for the struct, as we are going to use it for more events. Signed-off-by: NIdo Schimmel <idosch@mellanox.com> Reviewed-by: NPetr Machata <petrm@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ido Schimmel 提交于
We are going to need to respond to netevents notifying us about multipath hash updates by configuring the device's hash parameters. Embed the netevent notifier in the router struct so that we could retrieve it upon notifications and use it to configure the device. Signed-off-by: NIdo Schimmel <idosch@mellanox.com> Reviewed-by: NPetr Machata <petrm@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 02 11月, 2017 2 次提交
-
-
由 Greg Kroah-Hartman 提交于
Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: NKate Stewart <kstewart@linuxfoundation.org> Reviewed-by: NPhilippe Ombredanne <pombredanne@nexb.com> Reviewed-by: NThomas Gleixner <tglx@linutronix.de> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Jiri Pirko 提交于
This restores the original behaviour before the block callbacks were introduced. Allow the drivers to do binding of block always, no matter if the NETIF_F_HW_TC feature is on or off. Move the check to the block callback which is called for rule insertion. Reported-by: NAlexander Duyck <alexander.duyck@gmail.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 01 11月, 2017 3 次提交
-
-
由 Vadim Pasternak 提交于
It fixes a problem for the last chunk where 'chunk_size' is smaller than MLXSW_I2C_BLK_MAX and data is copied to the wrong offset, overriding previous data. Fixes: 6882b0ae ("mlxsw: Introduce support for I2C bus") Signed-off-by: NVadim Pasternak <vadimp@mellanox.com> Reviewed-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ido Schimmel 提交于
The ASIC has the ability to generate events whenever a sensor indicates the temperature goes above or below its high or low thresholds, respectively. In new firmware versions the firmware enforces a minimum of 5 degrees Celsius difference between both thresholds. Make the driver conform to this requirement. Note that this is required even when the events are disabled, as in certain systems interrupts are generated via GPIO based on these thresholds. Fixes: 85926f87 ("mlxsw: reg: Add definition of temperature management registers") Signed-off-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David Ahern 提交于
Adding a FIB rule on a spectrum platform silently aborts FIB offload: $ ip ru add pref 99 from all to 192.168.1.1 table 10 $ dmesg -c [ 623.144736] mlxsw_spectrum 0000:03:00.0: FIB abort triggered. Note that FIB entries are no longer being offloaded to this device. This patch reworks FIB rule handling to return a message to the user: $ ip ru add pref 99 from all to 8.8.8.8 table 11 Error: spectrum: FIB rules not supported. Aborting offload. spectrum currently only checks whether the fib rule is a default rule or an l3mdev rule, both of which it knows how to handle. Any other it aborts FIB offload. Move the processing to check the rule type inline with the user request. If the rule is an unsupported one, then a work queue entry is used to abort the offload. Change the rule delete handling to just return since it does nothing at the moment. Signed-off-by: NDavid Ahern <dsahern@gmail.com> Reviewed-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 27 10月, 2017 2 次提交
-
-
由 Nogah Frankel 提交于
Replace recurring magic number in PPCNT register with a define. Signed-off-by: NNogah Frankel <nogahf@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Nogah Frankel 提交于
Change the HW stats cache to be local. Rename it for better clarity. It holds the results of the last result of HW stats that are being read periodically, in order to have answer for stats request immediately. Signed-off-by: NNogah Frankel <nogahf@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 24 10月, 2017 4 次提交
-
-
由 Yotam Gigi 提交于
Make the spectrum_mr_tcam.c include the spectrum_mr_tcam.h header file. Cleans up sparse warning: symbol 'mlxsw_sp_mr_tcam_ops' was not declared. Should it be static? Fixes: 0e14c777 ("mlxsw: spectrum: Add the multicast routing hardware logic") Signed-off-by: NYotam Gigi <yotamg@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yotam Gigi 提交于
The function is only used internally in spectrum_mr.c and is not declared in the header file, thus make it static. Cleans up sparse warning: symbol 'mlxsw_sp_mr_dev_vif_lookup' was not declared. Should it be static? Fixes: c011ec1b ("mlxsw: spectrum: Add the multicast routing offloading logic") Signed-off-by: NYotam Gigi <yotamg@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yotam Gigi 提交于
Fix various endianness issues in comparisons and assignments. The fix is entirely cosmetic as all the values fixed are endianness-agnostic. Cleans up sparse warnings: spectrum_mr.c:156:49: warning: restricted __be32 degrades to integer spectrum_mr.c:206:26: warning: restricted __be32 degrades to integer spectrum_mr.c:212:31: warning: incorrect type in assignment (different base types) spectrum_mr.c:212:31: expected restricted __be32 [usertype] addr4 spectrum_mr.c:212:31: got unsigned int spectrum_mr.c:214:32: warning: incorrect type in assignment (different base types) spectrum_mr.c:214:32: expected restricted __be32 [usertype] addr4 spectrum_mr.c:214:32: got unsigned int spectrum_mr.c:461:16: warning: restricted __be32 degrades to integer spectrum_mr.c:461:49: warning: restricted __be32 degrades to integer Fixes: c011ec1b ("mlxsw: spectrum: Add the multicast routing offloading logic") Signed-off-by: NYotam Gigi <yotamg@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Arkadi Sharshevsky 提交于
During the dump the per netlink packet entry counter should be zeroed out when new packet is created. Fixes: 190d38a5 ("mlxsw: spectrum_dpipe: Add support for adjacency table dump") Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com> Reported-by: NDavid Ahern <dsahern@gmail.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 23 10月, 2017 6 次提交
-
-
由 Ido Schimmel 提交于
The KVD linear is currently partitioned into two partitions. One for single entries and another for groups of 32 entries. Add another partition consisting of groups of 512 entries which will allow us to more accurately represent the nexthop weights in non-equal cost multi-path routing. Signed-off-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ido Schimmel 提交于
The memory region where adjacency entries (nexthops) are stored is called the KVD linear and is configured during initialization with a size of 64K. Extend this area with 32K more entries, that will be partitioned into 64 groups of 0.5K entries, thereby allowing us to support weighted nexthops with high accuracy. Change the ratio between both types of hash entries, so as to prevent reduction in the number of double hash entries, which are used for IPv6 neighbours and routes with a prefix length greater than 64. Note that the user will be able to control all these sizes once the devlink resource manager is introduced. Signed-off-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ido Schimmel 提交于
Up until now the driver assumed all the nexthops have an equal weight and wrote each to a single adjacency entry. This patch takes the `weight` parameter into account and populates the adjacency group according to the relative weight of each nexthop. Specifically, the weights of all the nexthops that should be offloaded are first normalized and then used to calculate the upper adjacency index of each nexthop. This is done according to the hash-threshold algorithm used by the kernel for IPv4 multi-path routing. Adjacency groups are currently limited to 32 entries which limits the weights that can be used, but follow-up patches will introduce groups of 512 entries. Signed-off-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ido Schimmel 提交于
The device has certain restrictions regarding the size of an adjacency group. Have the router determine the size of the adjacency group according to available KVDL allocation sizes and these restrictions. This was not needed until now since only allocations of up 32 entries were supported and these are all valid sizes for an adjacency group. Signed-off-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ido Schimmel 提交于
As the first step towards non-equal-cost multi-path support, store each nexthop's weight. For IPv6 nexthops always set the weight to 1, as it only supports ECMP. Signed-off-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ido Schimmel 提交于
The current KVDL allocation API allows the user to specify the requested number of entries, but the user has no way of knowing how many entries were actually allocated. This works because existing users (e.g., router) request the exact number they end up using. With the introduction of large adjacency groups, this will change, as the router will have the ability to choose from several allocation sizes, where larger allocations provide higher accuracy with respect to requested weights and better resilience against nexthop failures. One option is to have the router try several allocations of descending size until one succeeds, but a better way is to simply allow it to query the actual allocation size and then size its request accordingly. Signed-off-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-