1/ I really should be using the __ATTR macros for defining attributes, so
   that the .owner field get set properly, otherwise modules can be removed
   while sysfs files are open.  This also involves some name changes of _show
   routines.

2/ Always lock the mddev (against reconfiguration) for all sysfs attribute
   access.  This easily avoid certain races and is completely consistant with
   other interfaces (ioctl and /proc/mdstat both always lock against
   reconfiguration).

3/ raid5 attributes must check that the 'conf' structure actually exists
   (the array could have been stopped while an attribute file was open).

4/ A missing 'kfree' from when the raid5_conf_t was converted to have a
   kobject embedded, and then converted back again.
Signed-off-by: NNeil Brown <neilb@suse.de>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

A sync of raid5 usually ignore blocks which the bitmap says are in-sync.  But
a user-request check or repair should not ignore these.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Raid1 currently optimises resync using the intent bitmap etc.  This
optimisation is not wanted when we explicitly request a repair through sysfs,
so add appropriate checks.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

If a block_device is a partition, then it's kobject is
  bdev->bd_part->kobj
otherwise (if it is a full device), the kobject is
  bdev->bd_disk->kobj

As md wants back-links to the correct object (whether partition or not), we
need to respect this difference...  (Thus current code shows a link to the
whole device, whether we are using a partition or not, which is wrong).
Signed-off-by: NNeil Brown <neilb@suse.de>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

When an md array is started, the superblock will be written, and resync may
commense.  This is not good if you want to be completely read-only as, for
example, when preparing to resume from a suspend-to-disk image.

So introduce a module parameter "start_ro" which can be set
to '1' at boot, at module load, or via
  /sys/module/md_mod/parameters/start_ro

When this is set, new arrays get an 'auto-ro' mode, which disables all
internal io (superblock updates, resync, recovery) and is automatically
switched to 'rw' when the first write request arrives.

The array can be set to true 'ro' mode using 'mdadm -r' before the first
write request, or resync can be started without a write using 'mdadm -w'.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

With version-0.90 superblock, component devices on an md device to not have
any stable name related to the array -(version-1 assigns a fixed index when
a device is added to an array, and this remains despit any hot-swap).

The intial code for making these devices appear in sysfs used dynamic
names, which would change whenever a hot-spare was swapped for a failed or
missing device.  This turns out not to be practical in sysfs for a number
of reasons.

This patch changes then naming of component devices to be based on the
result of 'bdevname'.  This is stable and should be unique.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

We can only accept BARRIER requests if all slaves handle
barriers, and that can, of course, change with time....

So we keep track of whether the whole array seems safe for barriers,
and also whether each individual rdev handles barriers.

We initially assumes barriers are OK.

When writing the superblock we try a barrier, and if that fails, we flag
things for no-barriers.  This will usually clear the flags fairly quickly.

If writing the superblock finds that BIO_RW_BARRIER is -ENOTSUPP, we need to
resubmit, so introduce function "md_super_wait" which waits for requests to
finish, and retries ENOTSUPP requests without the barrier flag.

When writing the real raid1, write requests which were BIO_RW_BARRIER but
which aresn't supported need to be retried.  So raid1d is enhanced to do this,
and when any bio write completes (i.e.  no retry needed) we remove it from the
r1bio, so that devices needing retry are easy to find.

We should hardly ever get -ENOTSUPP errors when writing data to the raid.
It should only happen if:
  1/ the device used to support BARRIER, but now doesn't.  Few devices
     change like this, though raid1 can!
or
  2/ the array has no persistent superblock, so there was no opportunity to
     pre-test for barriers when writing the superblock.
Signed-off-by: NNeil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Current bitmaps use set_bit et.al and so are host-endian, which means
not-portable.  Oops.

Define a new version number (4) for which bitmaps are little-endian.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This has the advantage of removing the confusion caused by 'rdev_t' and
'mddev_t' both having 'in_sync' fields.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Two refinements to the 'attempt-overwrite-on-read-error' mechanism.
1/ If the array is read-only, don't attempt an over-write.
2/ If there are more than max_nr_stripes read errors on a device with
   no success, fail the drive.  This will make sure a dead
   drive will be eventually kicked even when we aren't trying
   to rewrite (which would normally kick a dead drive more quickly.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

There isn't really a need for raid5 attributes to be an a subdirectory,
so this patch moves them from
  /sys/block/mdX/md/raid5/attribute
to
  /sys/block/mdX/md/attribute

This suggests that all md personalities should co-operate about
namespace usage, but that shouldn't be a problem.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

1/ Use reduce stack usage, because 'gcc' apparently doesn't overlay
   different variables  that are in separate scopes...

2/ Use test_bit instead of ( .. & 1<< ..) which in this case is buggy.

Thanks to Andrew Morton
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Thanks Greg.

Cc:  Greg KH <greg@kroah.com>
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Acked-by: <paulmck@us.ibm.com>
Signed-off-by: NSuzanne Wood <suzannew@cs.pdx.edu>
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

With this, raid5 can be asked to check parity without repairing it.  It also
keeps a count of the number of incorrect parity blocks found (mismatches) and
reports them through sysfs.
Signed-off-by: NNeil Brown <neilb@suse.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

You can trigger a 'check' with
  echo check > /sys/block/mdX/md/scan_mode
or a check-and-repair errors with
  echo repair > /sys/block/mdX/md/scan_mode

and read the current state from the same file.

Note: personalities need to know the different between 'check' and 'repair',
but don't yet.  Until they do, 'check' will be the same as 'repair' and will
just do a normal resync pass.
Signed-off-by: NNeil Brown <neilb@suse.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

/sys/block/mdX/md/raid5/
contains raid5-related attributes.
Currently
  stripe_cache_size
is number of entries in stripe cache, and is settable.
  stripe_cache_active
is number of active entries, and in only readable.
Signed-off-by: NNeil Brown <neilb@suse.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Each device in an md array how has a corresponding
  /sys/block/mdX/md/devNN/
directory which can contain attributes.  Currently there is only 'state' which
summarises the state, nd 'super' which has a copy of the superblock, and
'block' which is a symlink to the block device.

Also, /sys/block/mdX/md/rdNN represents slot 'NN' in the array, and is a
symlink to the relevant 'devNN'.  Obviously spare devices do not have a slot
in the array, and so don't have such a symlink.
Signed-off-by: NNeil Brown <neilb@suse.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Start using kobjects in mddevs, and provide a couple of simple attributes
(level and disks).  Attributes live in
  /sys/block/mdX/md/attr-name
Signed-off-by: NNeil Brown <neilb@suse.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch changes the behaviour of raid5 when it gets a read error.
Instead of just failing the device, it tried to find out what should have
been there, and writes it over the bad block.  For some media-errors, this
has a reasonable chance of fixing the error.  If the write succeeds, and a
subsequent read succeeds as well, raid5 decided the address is OK and
conitnues.

Instead of failing a drive on read-error, we attempt to re-write the block,
and then re-read.  If that all works, we allow the device to remain in the
array.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch removes almost all inclusions of linux/version.h.  The 3
#defines are unused in most of the touched files.

A few drivers use the simple KERNEL_VERSION(a,b,c) macro, which is
unfortunatly in linux/version.h.

There are also lots of #ifdef for long obsolete kernels, this was not
touched.  In a few places, the linux/version.h include was move to where
the LINUX_VERSION_CODE was used.

quilt vi `find * -type f -name "*.[ch]"|xargs grep -El '(UTS_RELEASE|LINUX_VERSION_CODE|KERNEL_VERSION|linux/version.h)'|grep -Ev '(/(boot|coda|drm)/|~$)'`

search pattern:
/UTS_RELEASE\|LINUX_VERSION_CODE\|KERNEL_VERSION\|linux\/\(utsname\|version\).h
Signed-off-by: NOlaf Hering <olh@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Use schedule_timeout_interruptible() instead of
set_current_state()/schedule_timeout() to reduce kernel size.
Signed-off-by: NNishanth Aravamudan <nacc@us.ibm.com>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Instead of having ->read_sectors and ->write_sectors, combine the two
into ->sectors[2] and similar for the other fields. This saves a branch
several places in the io path, since we don't have to care for what the
actual io direction is. On my x86-64 box, that's 200 bytes less text in
just the core (not counting the various drivers).
Signed-off-by: NJens Axboe <axboe@suse.de>

This patch uses sg_set_buf/sg_init_one in some places where it was
duplicated.
Signed-off-by: NDavid Hardeman <david@2gen.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Greg KH <greg@kroah.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

There are still a couple of cases where md threads (the resync/recovery
thread) is not interruptible since the change to use kthreads.  All places
there it tests "signal_pending", it should also test kthread_should_stop,
as with this patch.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The main problem fixes is that in certain situations stopping md arrays may
take longer than you expect, or may require multiple attempts.  This would
only happen when resync/recovery is happening.

This patch fixes three vaguely related bugs.

1/ The recent change to use kthreads got the setting of the
   process name wrong.  This fixes it.
2/ The recent change to use kthreads lost the ability for
   md threads to be signalled with SIG_KILL.  This restores that.
3/ There is a long standing bug in that if:
    - An array needs recovery (onto a hot-spare) and
    - The recovery is being blocked because some other array being
       recovered shares a physical device and
    - The recovery thread is killed with SIG_KILL
   Then the recovery will appear to have completed with no IO being
   done, which can cause data corruption.
   This patch makes sure that incomplete recovery will be treated as
   incomplete.

Note that any kernel affected by bug 2 will not suffer the problem of bug
3, as the signal can never be delivered.  Thus the current 2.6.14-rc
kernels are not susceptible to data corruption.  Note also that if arrays
are shutdown (with "mdadm -S" or "raidstop") then the problem doesn't
occur.  It only happens if a SIGKILL is independently delivered as done by
'init' when shutting down.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

 - added typedef unsigned int __nocast gfp_t;

 - replaced __nocast uses for gfp flags with gfp_t - it gives exactly
   the same warnings as far as sparse is concerned, doesn't change
   generated code (from gcc point of view we replaced unsigned int with
   typedef) and documents what's going on far better.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

When creating a multipath device, if the queue_if_no_path parameter is
specified it gets ignored.

While the queue_if_no_path variable is correctly set to 1, the
saved_queue_if_no_path gets set to 0.  When the device is subsequently made
live (resumed), the saved value (0) always overwrites the live value (1) so
the option *always* gets turned off.

The fix adds a parameter to the queue_if_no_path() function to indicate
whether the previous value should be preserved or not - if not, as when the
device is being set up, the saved value is set to the new value (1).
Signed-Off-By: NAlasdair G Kergon <agk@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

If anything is waiting on a device's table when the device is removed, we
must first wake it up so it will release its reference.  Otherwise the
table's reference count will not drop to zero and the table will not get
removed.
Signed-Off-By: NAlasdair G Kergon <agk@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch fixes a signedness bug with RAID6 for Altivec, and makes the
Altivec code testable in userspace.
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch contains the most trivial from Rusty's trivial patches:
- spelling fixes
- remove duplicate includes
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch does a full cleanup of 'NULL checks before vfree', and a partial
cleanup of calls to kfree for all of drivers/ - the kfree bit is partial in
that I only did the files that also had vfree calls in them.  The patch
also gets rid of some redundant (void *) casts of pointers being passed to
[vk]free, and a some tiny whitespace corrections also crept in.
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This shouldn't be a BUG.  We should cope.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

If you try to assemble an array with too many missing devices, raid10 will now
reject the attempt, instead of allowing it.

Also check when hot-adding a drive and refuse the hot-add if the array is
beyond hope.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

There was another case where sb_size wasn't being set, so instead do the
sensible thing and set if when filling in the content of a superblock.  That
ensures that whenever we write a superblock, the sb_size MUST be set.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

[PATCH] md: make sure the new 'sb_size' is set properly device added without pre-existing superblock.

There are two ways to add devices to an md/raid array.

  It can have superblock written to it, and then given to the md driver,
  which will read the superblock (the new way)

or

  md can be told (through SET_ARRAY_INFO) the shape of the array, and
  the told about individual drives, and md will create the required
  superblock (the old way).

The newly introduced sb_size was only set for drives being added the
new way, not the old ways.  Oops :-(
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Just like failed drives have (F), so spare drives now have (S).
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Leave it unchanged if the original (0.90) is used, incase it might be a
compatability problem.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Doh.  I want the physical hard-sector-size, not the current block size...
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>