And support setting both long and short retries independently.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

RF kill support is enabled when CONFIG_RFKILL
is set.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some of the functions in main.c are re-ordered in such
a way that all local functions are defined before mac80211
and pci callbacks.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The generic reset command is unused.  Each interface type needs to
handle the reset command differently since after reset, the firmware is
dead and interface-specific mechanisms must be used to reinitialize the
card.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This cleans up zd1211rw's own regulatory work, and makes use of
the new cfg80211 regulatory_hint().
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Noticed by Michael Chan.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

iwconfig txpower can now be used to set tx power to fixed or auto. If set to
auto the default firmware settings are used.

The command CMD_802_11_PA_CFG is only sent to older firmware, as Dan Williams
noted the command was no longer supported in firmware V9+.
Signed-off-by: NAnna Neal <anna@cozybit.com>
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Added support for 3 antennas for Legacy, SISO and MIMO2.
MIMO3 is still not supported yet.
Signed-off-by: NGuy Cohen <guy.cohen@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes a bug in Rate Scaling. When moving from SISO to MIMO we
need to choose the lowest higher rate, instead of choosing the highest in MIMO.
No doing this can lead to a high packet loss in the highest rate in MIMO,
leading not to move MIMO although lower in MIMO could give a better TPT.
Signed-off-by: NGuy Cohen <guy.cohen@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Simplify pass_packet_to_mac80211 code block.
Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If certain commands were in-flight when the card was pulled or the
driver rmmod-ed, cleanup would block on the work queue stopping, but the
work queue was in turn blocked on the current command being canceled,
which didn't happen.  Fix that.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There isn't really a good reason to have the LED
configuration options selectable per driver, lets
make it default 'y' and make it depend on the
NEW_LEDS and LEDS_CLASS interface.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

RFKILL should be enabled for _all_ hardware whether
or not they feature a rfkill button or not.

Remove driver specific RFKILL configuration options
and make the rt2x00lib version depend on CONFIG_RFKILL
and defaulting to 'y' to make sure it will always
be enabled when RFKILL was enabled.

This also fixes some bugs where RFKILL wasn't initialized
and didn't respond to RFKILL key presses.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reverts:
	b93ce437
	rt2x00: Fix the beacon length bug

The workaround is no longer required since it has been
correctly fixed in rt2x00usb now.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Recent changes in the specifications have improved the performance
of the BCM4306/2 devices that use b43legacy as the driver. These
"errors" in the specs have been present from the very first implementation
of bcm43xx.
Signed-off-by: NEhud Gavron <gavron@wetwork.net>
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A coding error present since b43legacy was incorporated into the
kernel has prevented the driver from using the rate-setting mechanism
of mac80211. The driver has been forced to remain at a 1 Mb/s rate.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>		[2.6.26], [2.6.25]
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We don't need the workqueue anymore, as we can now sleep in the callback.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It causes compile errors on m68k and it is not needed.
Remove it.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes the initialization of the default QoS parameters.
This got broken by "wireless: fix warnings from QoS patch".

Reported-by: Lorenzo Nava
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch brings the 5GHz Phy in any prism54 devices (of course, only those who have one) to life.
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I hope this patch is enough to cover at least the basic requirements of IEEE 802.11h's TPC.
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The firmware can provide lots of useful statistics about noise floor,
mac time and lots of numbers about successful transfers and dropped
frames.
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds new filters settings to make the card more useful in monitor mode.
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

tcpdump:
02:15:42.874518 61112184us tsft 48.0 Mb/s 2437 MHz (0x0480) antenna 1 [0x0000000e] CF +QoS Data IV
02:15:42.874557 >>>4356079526us<<< tsft 24.0 Mb/s 2437 MHz (0x0480) antenna 1 [0x0000000e] Acknowledgment
02:15:42.976844 61214513us tsft 1.0 Mb/s 2437 MHz (0x0480) antenna 0 [0x0000000e] Beacon

as one can see on the huge jump, it's very plausible that firmware does not report the
full 64-bit mac time, just the lower 32bit and some kinds of flags...
Therefore if we want a useful timestamp we have to emulate the high bits.
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The patch fixes compile warning for ‘iwl4965_hw_channel_switch’ defined
but not used.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch cleans up iwlwifi by removing uneeded declarations and removing
uneeded symbol export reducing the namespace pollution. It also fixes some
typos in comments.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch makes usage of the results from disconnected antenna alg to
know how many antennas are connected.

It also synchronizes between the chain noise alg and the W/A that
disables power management during association. All the antennas must be
enables during the chain noise algorithm. Hence, power management is
restored only after the completion of the algorithm.

In the future, we will need to update the AP that we don't support MIMO
if there is only one antenna connected. We also need to update the rate
scaling algorithm.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch renames iwl_priv.ps_mode for clearer
iwl_priv.current_ht_config.sm_ps (spatial multiplexing power save).
Signed-off-by: NRon Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch follows 11n spec naming more rigorously replacing MIMO_PS
with SM_PS (Spatial Multiplexing Power Save).

(Originally submitted as 4 patches, "mac80211: change MIMO_PS to SM_PS",
"iwlwifi: change MIMO_PS to SM_PS", "ath9k: change MIMO_PS to SM_PS",
and "iwlwifi: remove double definition of SM PS". -- JWL)
Signed-off-by: NRon Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use TX control flag IEEE80211_TX_CTL_ASSIGN_SEQ as a request to update
the seq# for the frames. This will likely require some further cleanup
to get seq# correctly for Beacons vs. other frames and also potentially
for multiple BSSes. Anyway, this is better than ending up sending out
most frames with seq# 0.

(This is a backport of patch w/ same title already in net-next-2.6.
It is verified to fix http://bugzilla.kernel.org/show_bug.cgi?id=11394
and it should be acceptable for -rc due to the driver being new
in 2.6.27.)
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When EEH detects an i/o error it resets the device thus it cannot be accessed.
In this case the driver needs to unload its interface only with OS, kernel and
network stack but not with the device.
After successful recovery, the driver can load normally.
Signed-off-by: NYitchak Gertner <gertner@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Handle station IDs of transmitted packets when in monitor mode, and
remove the various anti-injection checks from the iwl4965 driver.
This makes injection work on iwl4965 and iwl5000. Tested on both cards.

Note: To inject management frames with encryption, HW crypto support
must be disabled using the "swcrypto=1" modparam (or "swcrypto50=1"
for iwl5000). Otherwise most management frames won't be transmitted.
Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch enables active scanning on active channels.
Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes bad language in the comments in iwl-agn-rs.c.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes regression in iwlwifi IBSS rate scaling caused by the
patch named "mac80211: eliminate IBSS warning in rate_lowest_index()"
by Vladimir Koutny <vlado@work.ksp.sk>.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch aligns definition of host command with the spec. The
inaccuracies weren't critical though.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch disables power save upon association and enables it back
after association. This allows to associate to AP on a radar channel
if power save is enabled.

Radar and passive channels are not allowed for TX (required for association)
unless RX is received but PS may close the radio and no RX will be received
effectively failing association.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NMohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch cleans up pci registers handling.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes handling of strcit_strtoul return value
"0 == sucess".
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>