- 04 5月, 2006 1 次提交
-
-
由 mark gross 提交于
Address the issue of EDAC/BIOS coexistence for the e752x chip-sets. We have found a problem where the BIOS will start the system with the error registers (dev0:fun1) hidden and assuming it has exclusive access to them. The edac driver violates this assumption. The workaround this patch offers is to honor the hidden-ness as an indication that it is not safe to use those registers. Signed-off-by: NMark Gross <mark.gross@intel.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 03 5月, 2006 3 次提交
-
-
由 Ayaz Abdulla 提交于
This patch fixes the issues with multiple irqs. I am resending based on feedback. I decoupled the dma mask for consistent memory and fixed leak with multiple irq in error path. Thanks to Manfred for catching the spin lock problem. Signed-Off-By: NAyaz Abdulla <aabdulla@nvidia.com>
-
由 Craig Brind 提交于
Fixes Rhine I cards disclosing fragments of previously transmitted frames in new transmissions. Before transmission, any socket buffer (skb) shorter than the ethernet minimum length of 60 bytes was zero-padded. On Rhine I cards the data can later be copied into an aligned transmission buffer without copying this padding. This resulted in the transmission of the frame with the extra bytes beyond the provided content leaking the previous contents of this buffer on to the network. Now zero-padding is repeated in the local aligned buffer if one is used. Following a suggestion from the via-rhine maintainer, no attempt is made here to avoid the duplicated effort of padding the skb if it is known that an aligned buffer will definitely be used. This is to make the change "obviously correct" and allow it to be applied to a stable kernel if necessary. There is no change to the flow of control and the changes are only to the Rhine I code path. The patch has run on an in-service Rhine-I host without incident. Frames shorter than 60 bytes are now correctly zero-padded when captured on a separate host. I see no unusual stats reported by ifconfig, and no unusual log messages. Signed-off-by: NCraig Brind <craigbrind@gmail.com> Signed-off-by: NRoger Luethi <rl@hellgate.ch> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Olaf Hering 提交于
On Sat, Mar 11, Olaf Hering wrote: > Why is the /sys/class/net/eth0/device symlink not created for the > mv643xx_eth driver? Does this work for other platform device drivers? > Seems to work for the ps2 keyboard at least. The SET_NETDEV_DEV has to be done before a call to register_netdev. With the new patch below, the device symlink for the platform device was created. Unfortunately, after the 4 ls commands, the network connection died. No idea if the box crashed or if something else broke, lost remote access. Provide sysfs 'device' in /class/net/ethN Also, set module owner field, like pcnet32 driver does. Signed-off-by: NOlaf Hering <olh@suse.de> Acked-by: NDale Farnsworth <dale@farnsworth.org> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
- 02 5月, 2006 22 次提交
-
-
由 Atsushi Nemoto 提交于
Fix genrtc's read() routine for 64-bit platforms. Current gen_rtc_read() stores 64bit integer and returns 8 even if an user tried to read a 32bit integer. Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp> Cc: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Atsushi Nemoto 提交于
Make rtc-dev work well on 64-bit platforms with 32-bit userland. On those platforms, users might try to read 32-bit integer value. This patch make rtc-dev's read() work well for both "int" and "long" size. This tweak is came from genrtc driver. Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp> Cc: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Heiko Carstens 提交于
As pointed out by Paulo Marques <pmarques@grupopie.com> MAX_IPD_TIME is by a factor of ten too small. Since this means that we allow ten times more IPDs in the intended time frame this could result in a cpu check stop of a physical cpu. Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Pat Gefre 提交于
Currently loading the ioc3 as a module will cause the ports to be numbered in reverse order. This mod maintains the proper order of cards for port numbering. Signed-off-by: NPatrick Gefre <pfg@sgi.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 NeilBrown 提交于
When retrying a failed BIO_RW_BARRIER request, we need to keep the reference in ->nr_pending over the whole retry. Currently, we only hold the reference if the failed request is the *last* one to finish - which is silly, because it would normally be the first to finish. So move the rdev_dec_pending call up into the didn't-fail branch. As the rdev isn't used in the later code, calling rdev_dec_pending earlier doesn't hurt. Signed-off-by: NNeil Brown <neilb@suse.de> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 NeilBrown 提交于
Move the test for 'do barrier work' down a bit so that if the first write to a raid1 is a BIO_RW_BARRIER write, the checking done by superblock writes will cause the right thing to happen. Signed-off-by: NNeil Brown <neilb@suse.de> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 NeilBrown 提交于
Because that is what you get if a BIO_RW_BARRIER isn't supported! Signed-off-by: NNeil Brown <neilb@suse.de> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 NeilBrown 提交于
We need to hold a reference to rdevs while reading and writing to attempt to correct read errors. This reference must be taken under an rcu lock. Signed-off-by: NNeil Brown <neilb@suse.de> Cc: "Paul E. McKenney" <paulmck@us.ibm.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 NeilBrown 提交于
We should add to the counter for the rdev *after* checking if the rdev is NULL!!! Signed-off-by: NNeil Brown <neilb@suse.de> Cc: <stable@kernel.org> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Bastian Blank 提交于
Signed-off-by: NBastian Blank <bastian@waldi.eu.org> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: "David S. Miller" <davem@davemloft.net> Acked-by: NJeff Garzik <jeff@garzik.org> Acked-by: NFrank Pavlic <fpavlic@de.ibm.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Bryan O'Sullivan 提交于
Signed-off-by: NBryan O'Sullivan <bos@pathscale.com> Signed-off-by: NRoland Dreier <rolandd@cisco.com>
-
由 Bryan O'Sullivan 提交于
Names that are the opposite of their intended meanings are not so helpful. Signed-off-by: NBryan O'Sullivan <bos@pathscale.com> Signed-off-by: NRoland Dreier <rolandd@cisco.com>
-
由 Bryan O'Sullivan 提交于
Signed-off-by: NBryan O'Sullivan <bos@pathscale.com> Signed-off-by: NRoland Dreier <rolandd@cisco.com>
-
由 Bryan O'Sullivan 提交于
Signed-off-by: NBryan O'Sullivan <bos@pathscale.com> Signed-off-by: NRoland Dreier <rolandd@cisco.com>
-
由 Bryan O'Sullivan 提交于
Remove some unnecessarily complicated tests. Signed-off-by: NBryan O'Sullivan <bos@pathscale.com> Signed-off-by: NRoland Dreier <rolandd@cisco.com>
-
由 Bryan O'Sullivan 提交于
The reset code now turns off the PRESENT flag during a reset, so that other code won't attempt to access a device that's in mid-reset. Signed-off-by: NBryan O'Sullivan <bos@pathscale.com> Signed-off-by: NRoland Dreier <rolandd@cisco.com>
-
由 Bryan O'Sullivan 提交于
Remember when the verbs layer unregisters from the lower-level code. Signed-off-by: NBryan O'Sullivan <bos@pathscale.com> Signed-off-by: NRoland Dreier <rolandd@cisco.com>
-
由 Bryan O'Sullivan 提交于
Different ipath hardware types have different numbers of buffers available, so we decide on the counts ourselves unless we are specifically overridden with a module parameter. Signed-off-by: NBryan O'Sullivan <bos@pathscale.com> Signed-off-by: NRoland Dreier <rolandd@cisco.com>
-
由 Bryan O'Sullivan 提交于
Signed-off-by: NBryan O'Sullivan <bos@pathscale.com> Signed-off-by: NRoland Dreier <rolandd@cisco.com>
-
由 Bryan O'Sullivan 提交于
Some systems do not set up 64-bit maps on systems with 2GB or less of memory installed, so we have to fall back to trying a 32-bit setup. Signed-off-by: NBryan O'Sullivan <bos@pathscale.com> Signed-off-by: NRoland Dreier <rolandd@cisco.com>
-
由 Bryan O'Sullivan 提交于
We were accidentally exposing the "reset" sysfs file more than once per device. Signed-off-by: NBryan O'Sullivan <bos@pathscale.com> Signed-off-by: NRoland Dreier <rolandd@cisco.com>
-
由 Roland Dreier 提交于
GuidInfo records have 8 byte GUIDs in them, so an index should be multiplied by 8 to get an offset. mthca_query_gid() was incorrectly multiplying by 16. Noticed by Leonid Keller <leonid@mellanox.co.il>. Signed-off-by: NRoland Dreier <rolandd@cisco.com>
-
- 30 4月, 2006 8 次提交
-
-
由 Michael Chan 提交于
Update version to 3.57. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Fix bug in nvram write function. If the starting nvram address offset happens to be the last dword of the page, the NVRAM_CMD_LAST bit will not get set in the existing code. This patch fixes the bug by changing the "else if" to "if" so that the last dword condition always gets checked. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Gary Zambrano 提交于
Add a reset_phy parameter to tg3_reset_hw() and tg3_init_hw(). With the full chip reset during MAC address change, the automatic PHY reset during chip reset will cause a link down and bonding will not work properly as a result. With this reset_phy parameter, we can do a chip reset without link down when changing MAC address or MTU. Signed-off-by: NGary Zambrano <zambrano@broadcom.com> Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Do the full chip reset when changing MAC address if ASF is enabled. ASF sometimes uses a different MAC address than the driver. Without the reset, the ASF MAC address may be overwritten when the driver's MAC address is changed. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Add some PHY workaround code to reduce jitter on some PHYs. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Add netif_carrier_off() call during tg3_phy_reset(). This is needed to properly track the netif_carrier state in cases where we do a PHY reset with interrupts disabled. The SerDes code will not run properly if the netif_carrier state is wrong. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ralf Baechle 提交于
Content of file au1200fb.c was duplicated. Remove. Signed-off-by: NRalf Baechle <ralf@linux-mips.org> Signed-off-by: NAntonino Daplas <adaplas@pol.net> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Linus Torvalds 提交于
Let people enable the advansys driver on x86-32, even though it's broken on other architectures due to missing DMA mapping infrastructure. It's used by Jeffrey Phillips Freeman <jeffreyfreeman@syncleus.com> and possibly others. Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 29 4月, 2006 3 次提交
-
-
由 Dmitry Torokhov 提交于
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
-
由 Dmitry Torokhov 提交于
While writing to an event device allows to set repeat rate for an individual input device there is no way to retrieve current settings so we need to ressurect EVIOCGREP. Also ressurect EVIOCSREP so we have a symmetrical interface. Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
-
由 Dmitry Torokhov 提交于
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
-
- 28 4月, 2006 3 次提交
-
-
由 Antonino A. Daplas 提交于
Add help text in Kconfig Signed-off-by: NAntonino Daplas <adaplas@pol.net> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Horst Hummel 提交于
Generate new sysfs-attribute 'uid' that contains an device specific unique identifier. This can be used to identity multiple ALIASES of the same physical device (PAV). In addition the sysfs-attributes 'vendor' (containing the manufacturer of the device) and 'alias' (identify alias or base device) is added. This is first part of PAV support in LPAR (also valid on zVM). Signed-off-by: NHorst Hummel <horst.hummel@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Heiko Carstens 提交于
In case of an instruction processing damage (IPD) machine check in kernel mode the resulting action is always to stop the kernel. This is not necessarily the best solution since a retry of the failing instruction might succeed. Add logic to retry the instruction if no more than 30 instruction processing damage checks occured in the last 5 minutes. Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-