Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 17 10月, 2007 9 次提交
  3. 16 10月, 2007 1 次提交
  5. 13 10月, 2007 9 次提交
  7. 12 10月, 2007 18 次提交
    • B
      ide: use only ->set_pio_mode method for programming PIO modes (take 2) · 8f4dd2e4
      由 Bartlomiej Zolnierkiewicz 提交于 
      Use ->set_pio_mode method to program PIO modes in ide_set_xfer_rate()
(the only place which used ->speedproc to program PIO modes) and remove
handling of PIO modes from all ->speedproc implementations.

v2:
* Fix pmac_ide_tune_chipset() comment.

There should be no functionality changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      8f4dd2e4
    • B
      sis5513: don't change UDMA settings when programming PIO · 0d3be723
      由 Bartlomiej Zolnierkiewicz 提交于 
      Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      0d3be723
    • B
      it8213/piix/slc90e66: don't change DMA settings when programming PIO · 90986028
      由 Bartlomiej Zolnierkiewicz 提交于 
      Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      90986028
    • B
      alim15x3: PIO mode setup fixes · a6fe837e
      由 Bartlomiej Zolnierkiewicz 提交于 
      * Return failure in ->speedproc method for unsupported/invalid transfer
  modes passed from user-space (fixes theoretical OOPS in ali_tune_pio()
  and/or setting random PIO timings on host controller + disabling UDMA
  bit + setting unsupported/invalid transfer mode on the device).

* Don't disable UDMA bit when programming PIO modes.

* Add FIXME about DMA timings never being set.

* Bump driver version.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      a6fe837e
    • B
      siimage: fix ->set_pio_mode method to select PIO data transfer · ffe5415c
      由 Bartlomiej Zolnierkiewicz 提交于 
      * Remember to select PIO data transfer (with IORDY monitored) in sil_tune_pio()
  (->set_pio_mode method) so the controller is always programmed correctly for
  PIO transfers (this is important if DMA is not going to be used).

* Don't set DMA/UDMA timings for PIO modes in siimage_tune_chipset().

* Bump driver version.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      ffe5415c
    • B
      cs5520: don't enable VDMA in ->speedproc · 326d72f4
      由 Bartlomiej Zolnierkiewicz 提交于 
      There is no need to do it in cs5520_tune_chipset() (->speedproc method)
since it is correctly handled by cs5520_dma_on() (->ide_dma_on method).
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      326d72f4
    • B
      sc1200: remove redundant warning message from sc1200_tune_chipset() · fabe1510
      由 Bartlomiej Zolnierkiewicz 提交于 
      ide_config_drive_speed() called by sc1200_set_xfer_mode() already gives
a meaningful warning message in case of failure.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      fabe1510
    • B
      sgiioc4: use ide_tune_dma() · ca1997c1
      由 Bartlomiej Zolnierkiewicz 提交于 
      * Add DRV_NAME define and use it instead of sgiioc4_chipset.name.

* Remove no longer needed sgiioc4_chipset.

* Remove needless clearing of ->atapi_dma from ide_dma_sgiioc4().

* Fix ide_dma_sgiioc4() to return success/failure.  Check return value in
  sgiioc4_ide_setup_pci_device() and set hwif->autodma accordingly.  Also add
  missing setting of drive->autodma.

* Add sgiioc4_speedproc() (implementation of ->speedproc method).

* Fix ->mwdma_mask (MWDMA2 mask is 0x04 not 0x02) and remove incorrect
  ->swdma_mask.  Also remove needless initialization of ->ultra_mask.

* Use ide_tune_dma() in sgiioc4_ide_dma_check(), this fixes following bugs:
  - DMA capability bit not being checked on the device
  - DMA blacklist not being checked
  - MWDMA2 mode support by device not being checked
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeremy Higdon <jeremy@sgi.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      ca1997c1
    • B
      amd74xx/via82cxxx: use ide_tune_dma() · 55f17e8d
      由 Bartlomiej Zolnierkiewicz 提交于 
      * Use ide_tune_dma() in amd74xx/via82cxxx driver, this fixes following bugs:
  - DMA capability bit not being checked on the device
  - DMA blacklist not being checked
  - DMA mode being programmed even if drive->autodma == 0
    (thus possibly destroying PIO timings)

* Bump driver version.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      55f17e8d
    • B
      ide: add ide_set{_max}_pio() (take 4) · 26bcb879
      由 Bartlomiej Zolnierkiewicz 提交于 
      * Add IDE_HFLAG_ABUSE_{PREFETCH,FAST_DEVSEL,DMA_MODES} flags
  and set them in ht6560, cmd640, cmd64x and sc1200 host drivers.

* Add set_pio_mode_abuse() for checking if host driver has a non-standard
  ->tuneproc() implementation and use it in do_special().

* Add ide_set_pio() for setting PIO mode (it uses hwif->pio_mask to find
  the maximum PIO mode supported by the host), also add ide_set_max_pio()
  wrapper for ide_set_pio() to use for auto-tuning.  Convert users of
  ->tuneproc to use ide_set{_max}_pio() where possible.  This leaves only
  do_special(), set_using_pio(), ide_hwif_restore() and ide_set_pio() as
  a direct users of ->tuneproc.

* Remove no longer needed ide_get_best_pio_mode() calls and printk-s
  reporting PIO mode selected from ->tuneproc implementations.

* Rename ->tuneproc hook to ->set_pio_mode and make 'pio' argument const.

* Remove stale comment from ide_config_drive_speed().

v2:
* Fix "ata_" prefix (Noticed by Jeff).

v3:
* Minor cleanups/fixups per Sergei's suggestions.

v4:
* Fix compile problem in drivers/ide/pci/cmd640.c
  (Noticed by Andrew Morton).

* Improve some ->set_pio_mode comments.
Reviewed-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      26bcb879
    • B
      ide: move ide_rate_filter() calls to the upper layer (take 2) · f212ff28
      由 Bartlomiej Zolnierkiewicz 提交于 
      * Move ide_rate_filter() calls from host drivers to IDE core.

* Make ide_rate_filter() static.

* Make 'speed' argument of ->speedproc const.

v2:
* Fix it8213_tune_chipset() comment.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      f212ff28
    • B
      sis5513: add ->udma_filter method for chipset_family >= ATA_133 · 3160d541
      由 Bartlomiej Zolnierkiewicz 提交于 
      * Add sis5513_ata133_udma_filter() for chipset_family >= ATA_133,
  use it to filter UDMA6 mode if ATA133 bit is disabled.

* Remove no longer needed UDMA6 limiting logic from sis5513_tune_chipset().

* Bump driver version.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      3160d541
    • B
      ide: mode limiting fixes for user requested speed changes · 7670df73
      由 Bartlomiej Zolnierkiewicz 提交于 
      * Add an extra argument to ide_max_dma_mode() for passing requested transfer
  mode.  Use it as an upper limit when finding the best DMA for device/host.

* Rename ide_max_dma_mode() to ide_find_dma_mode() and at the same time add
  ide_max_dma_mode() wrapper which passes XFER_UDMA_6 as a requested mode to
  ide_find_dma_mode().  Also add inline ide_find_dma_mode() version for
  CONFIG_BLK_DEV_IDEDMA=n case.

* Pass requested transfer mode from ide_find_dma_mode() to ide_get_mode_mask()
  to avoid false warning from eighty_ninty_three().

* Use ide_find_dma_mode() to limit the user requested transfer mode in
  ide_rate_filter().  Also limit the requested mode by host max PIO mode.


Above changes make ide_rate_filter() to:

* Clip desired transfer mode down if it is invalid (values 0x0F, 0x13-0x19
  and 0x25-0x39, values > 0x46 were already clipped down, same for values
  0x25-0x39 but iff UDMA was not supported by the host).

* Clip desired transfer mode down if it is currently unsupported by IDE core
  (PIO6 and MWDMA3-4, the latter were already clipped down but iff UDMA was
  not supported by the host).

* Clip desired transfer mode down according to the host capabilities
  (UDMA modes were already clipped down but MWDMA/SWDMA/PIO weren't,
  also ->atapi_dma flag was not respected).

* Clip desired transfer mode down according to the device capabilities
  (except PIO modes for now which require mode work) - shouldn't be a
  problem since ide_set_xfer_rate() is called _after_ device has accepted
  given transfer mode.

and also result in a number of host driver specific bugfixes:

* icside
  - clip unsupported PIO5 mode down
  - fix unsupported/invalid modes being set in drive->current_speed

* ide-cris
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - clip DMA modes down for ATAPI devices
  - fix BUG() on unsupported/invalid modes

* au1xxx-ide
  - clip unsupported PIO5, SWDMA0-2 and MWDMA0-2
    (if BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA=n) modes down

* aec62xx
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - clip DMA modes down for ATAPI devices
  - fix 0x00 being programmed as PIO timing for unsupported/invalid modes
  - fix unsupported/invalid modes being set on the device

* alim15x3
  - clip DMA modes down for ATAPI devices (chipset revision == 0x20 only)
  - fix theoretical OOPS for 0x0F mode
  - fix unsupported/invalid modes being set on the device

* amd74xx
  - clip unsupported SWDMA0-2 (on COBRA_7401 revs <= 7) modes down
  - fix random PIO timings being set for unsupported/invalid modes
  - fix unsupported/invalid modes being set on the device

* atiixp
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix cached MWDMA mode being cleared for unsupported/invalid modes
  - fix PIO{0,2} timings being programmed for unsupported/invalid modes
  - fix theoretical OOPS for PIO5-6 and 0x0F modes
  - fix unsupported/invalid modes being set on the device

* cmd64x
  - clip unsupported SWDMA0-2 modes down

* cs5530
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix unsupported/invalid modes being set on the device
  - fix BUG() on unsupported/invalid modes
    (which happened if the device accepted the setting)

* cs5535
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix unsupported/invalid modes being set on the device
  - fix theoretical OOPS for PIO5-6 and 0x0F modes

* hpt34x
  - clip DMA modes down for ATAPI devices
  - fix invalid timings being programmed for unsupported/invalid modes
  - fix unsupported/invalid modes being set on the device

* hpt366
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix PIO0 timings being programmed for unsupported/invalid modes
  - fix DMA timings being cleared for MWDMA3-4 and 0x25-0x39 modes
  - fix unsupported/invalid modes being set on the device

* it8213
  - clip unsupported PIO5, SWDMA0-1 and MWDMA0 modes down

* it821x
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - clip DMA modes down for ATAPI devices
    (chipset in smart mode and revision 0x10 in pass-through mode)

* jmicron
  - clip unsupported SWDMA0-2 modes down
  - fix unsupported/invalid modes being set on the device

* pdc202xx_new
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix unsupported/invalid modes being set on the device

* pdc202xx_old
  - clip unsupported PIO5 mode down
  - fix incorrect timings being set for unsupported/invalid modes
  - fix unsupported/invalid modes being set on the device

* piix
  - clip unsupported PIO5, SWDMA0-1 and MWDMA0 modes down

* sc1200
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix unsupported/invalid modes being set on the device
  - fix BUG() on unsupported/invalid modes
    (which happened if the device accepted the setting)

* scc_pata
  - clip unsupported PIO5, SWDMA0-2 and MWDMA0-2 modes down

* serverworks
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix DMA/UDMA timings/settings being cleared for unsupported/invalid modes
  - fix unsupported/invalid modes being set on the device

* siimage
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - clip DMA modes down for ATAPI devices (SATA chipsets)

* sis5513
  - clip unsupported PIO5 mode down
  - fix BUG() on unsupported/invalid modes

* sl82c105
  - clip unsupported SWDMA0-2 modes down

* slc90e66
  - clip unsupported PIO5, SWDMA0-1 and MWDMA0 modes down

* tc86c001
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix PIO0 timings being programmed for PIO5/0x0F/SWDMA0-2/0x13-0x19 modes
  - fix invalid 0x00 DMA timing being programmed for MWDMA3-4/0x25-0x39 modes
  - fix unsupported/invalid modes being set on the device

* triflex
  - clip unsupported PIO5 mode down

* via82cxxx
  - fix random PIO timings being set for unsupported/invalid modes
  - fix unsupported/invalid modes being set on the device

* pmac
  - clip unsupported PIO5 and SWDMA0-2 modes down

* cmd640/ht6560b
  - clip DMA modes down (if CONFIG_BLK_DEV_IDEDMA=y)
  - fix PIO5 being clipped to PIO4 (if CONFIG_BLK_DEV_IDEDMA=n)

* opti621
  - clip DMA modes down (if CONFIG_BLK_DEV_IDEDMA=y)
  - clip unsupported PIO4 to PIO3 (if CONFIG_BLK_DEV_IDEDMA=n)


While at it:

* Use ide_rate_filter() in cs5520.c::cs5520_tune_chipset().

* Remove no longer needed checks from hpt366.c::hpt3{6,7}x_tune_chipset().
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      7670df73
    • B
      ide: add missing ide_rate_filter() calls to ->speedproc()-s · a8028fcb
      由 Bartlomiej Zolnierkiewicz 提交于 
      * Fix icside, cris-ide, au1xxx-ide, amd74xx, via82cxxx and pmac host drivers
  to use ide_rate_filter().

  This results in the following modes (from user requests) being clipped down:
  - invalid modes (values 0x46-0xFF)  [ for all hosts ]
  - unsupported by a host UDMA modes  [ for hosts which support UDMA]
  - all UDMA modes and MWDMA3-4 modes [ for hosts which don't support UDMA ]
  - invalid modes (values 0x25-0x39)  [ for hosts which don't support UDMA ]

* Host driver specific changes in behavior:

  icside:
    - no change

  cris-ide
    - clip unsupported UDMA3-6 modes down
    - fix BUG() on trying to set unsupported UDMA3-6 modes

  au1xxx-ide/pmac
    - clip unsupported UDMA modes down

  amd74xx/via82cxxx
    - clip unsupported UDMA modes down
    - fix random PIO timings being set for unsupported/invalid modes
    - fix unsupported/invalid modes being set on the device

* While at it remove no longer needed checks from pmac.c driver.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      a8028fcb
    • T
      ide: make jmicron match vendor and device class · bda7970c
      由 Tejun Heo 提交于 
      PATA part of all current JMB controllers behave the same way and
JMicron confirms that all future ones will stay compatible.  Matching
vendor and device class is enough.

For backward compatibility, jmicron still needs to match 361,3,5,6,8
DIDs regardless of device class if libata is not configured but won't
need further DID update from this point.

Bart: cosmetic fixes to jmicron_chipset
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Ethan Hsiao <ethanhsiao@jmicron.com>
Cc: Justin Tsai <justin@jmicron.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      bda7970c
    • S
      pdc202xx_new: switch to using pci_get_slot() (take 2) · 07047935
      由 Sergei Shtylyov 提交于 
      Switch to using pci_get_slot() in init_setup_pdc20270() to get to the mate chip
behind DC21150 bridge as there's no need for the driver itself to walk the list
of the PCI devices (and the driver didn't check the bus # of the found device).
While at it, make it emit warning about IRQ # being fixed up (just like hpt366.c
does) and "beautify" this whole function as well as init_setup_pdc20276()...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      07047935
    • S
      hpt366: MWDMA filter for SATA cards (take 2) · b4e44369
      由 Sergei Shtylyov 提交于 
      The Marvell bridge chips used on HighPoint SATA cards do not seem to support
the MWDMA modes (at least that could be seen in their so-called drivers :-),
so the driver needs to account for this -- to achieve this:

- add mdma_filter() method from the original patch by Bartlomiej Zolnierkiewicz
  with his consent;

- install the method for all chips to only return empty mask if a SATA drive
  is detected on HPT372{AN]/374 chips...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      b4e44369
    • S
      atiixp: SB700 contains more than one IDE channel · 7cfa7168
      由 Shane Huang 提交于 
      SB700 supports one physical IDE channel, but SB700 SATA controller
supports combined mode.  When the SATA combined mode is enabled,
two SATA ports (port4 and port5) share one IDE channel from IDE
controller, and PATA will share the other IDE channel.

Our previous patch adding SB700 IDE device ID only supports one
IDE channel, which contains bug.  The attached patch fixes the bug.
Signed-off-by: N"Shane Huang" <Shane.Huang@amd.com>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      7cfa7168
  9. 10 10月, 2007 1 次提交
    • J
      drivers/firmware: const-ify DMI API and internals · 1855256c
      由 Jeff Garzik 提交于 
      Three main sets of changes:

1) dmi_get_system_info() return value should have been marked const,
   since callers should not be changing that data.

2) const-ify DMI internals, since DMI firmware tables should,
   whenever possible, be marked const to ensure we never ever write to
   that data area.

3) const-ify DMI API, to enable marking tables const where possible
   in low-level drivers.

And if we're really lucky, this might enable some additional
optimizations on the part of the compiler.

The bulk of the changes are #2 and #3, which are interrelated.  #1 could
have been a separate patch, but it was so small compared to the others,
it was easier to roll it into this changeset.
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
      1855256c
  11. 12 9月, 2007 2 次提交