After converting to generic pinconf binding, pinctrl-a10.h is now not
used at all.

Drop its inclusion for H3 DTSI.
Signed-off-by: NIcenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The skeleton.dtsi file is now deprecated, and do not exist in ARM64
environment.

Since we will soon reuse most part of H3 DTSI for H5, which is an ARM64
chip, drop skeleton.dtsi inclusion now.
Signed-off-by: NIcenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Since everybody copied my own mistake from the DT binding example,
let's address all the offenders in one swift go.

Most of them got the CPU interface size wrong (4kB, while it should
be 8kB), except for both keystone platforms which got the control
interface wrong (4kB instead of 8kB).

In a few cases where I knew for sure what implementation was used,
I've added the "arm,gic-400" compatible string. I'm 99% sure that
this is what everyone is using, but short of having the TRM for
all the other SoCs, I've left them alone.
Acked-by: NShawn Guo <shawnguo@kernel.org>
Acked-by: NTony Lindgren <tony@atomide.com>
Acked-by: NSantosh Shilimkar <ssantosh@kernel.org>
Acked-by: NKrzysztof Kozlowski <krzk@kernel.org>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NMatthias Brugger <matthias.bgg@gmail.com>
Acked-by: NHeiko Stuebner <heiko@sntech.de>
Reviewed-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Add the SPDIF transceiver controller block to the H3 dtsi.
Signed-off-by: NMarcus Cooper <codekipper@gmail.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add the SPDIF TX pin to the H3 dtsi.
Signed-off-by: NMarcus Cooper <codekipper@gmail.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Now that we support the audio codec found on the Allwinner H3 SoC, add
device nodes for it.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

In the past, all the MMC pins had

	allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;

which was actually a no-op. We were relying on U-boot to set the bias
pull up for us. These properties were removed as part of the fix up to
actually support no bias on the pins. During the transition some boards
experienced regular MMC time-outs during normal operation, while others
completely failed to initialize the SD card.

Given that MMC starts in open-drain mode and the pull-ups are required,
it's best to enable it for all the pin settings.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Now that we can handle the generic pinctrl bindings, convert our DT to it.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>

The allwinner,pull property set to NO_PULL was really considered our
default (and wasn't even changing the default value in the code).

Remove these properties to make it obvious that we do not set anything in
such a case.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>

The allwinner,drive property set to 10mA was really considered as our
default. Remove all those properties entirely to make that obvious.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>

In a previous commit, I made a copy/paste error in the pinmux
definitions of UART3: PG{13,14} instead of PA{13,14}. This commit takes
care of that. I have tested this commit on Orange Pi PC and Orange Pi
Plus, and it works for these boards.

Fixes: e3d11d3c ("dts: sun8i-h3: add pinmux definitions for
UART2-3")
Signed-off-by: NJorik Jonker <jorik@kippendief.biz>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The pin controllers also use the two oscillators for debouncing. Add them
to the DTs.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NChen-Yu Tsai <wens@csie.org>

H3 SPI subsystem is almost same as A31 SPI except buffer size, so those
DT properties are reusable.

Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: NMilo Kim <woogyom.kim@gmail.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

H3 supports two SPI controllers. Four pins (MOSI, MISO, SCLK, SS) are
configured through the pinctrl subsystem.

Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: NMilo Kim <woogyom.kim@gmail.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Use the new sun7i-a20-mmc compatible for the mmc controllers on sun7i
and newer.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

These peripherals can only be muxed to these pins, so they are
associated in the DTSI instead of the board files. This makes it very
easy to enable them using overlays or u-boot commands:

 => fdt set /soc/i2c@01c2ac00 status okay
Signed-off-by: NJorik Jonker <jorik@kippendief.biz>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

These are the only possible pins for these peripherals according to the
datasheet.
Signed-off-by: NJorik Jonker <jorik@kippendief.biz>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This was done to make UART1-3 on H3 consistent, and less complicated to
enable UART1-3 on the breakout header on the several H3 board (notably
Orange Pi's). This patch adds a bit of complexity for the existing Banana
Pi, which already had the RTS/CTS associated on UART1.

The RTS/CTS for UART2-3 could be defined in the same way, but since
there is no actual use case for them at the moment, they are left out.
Signed-off-by: NJorik Jonker <jorik@kippendief.biz>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

These are the pinmux definitions for UART2-3 on H3. These UARTs can only
be muxed to these pins, so _a and @0 do not really make sense. I have
left out RTS/CTS, since these are rarely used. These can easily be
enabled using an additional pinmux set.
Signed-off-by: NJorik Jonker <jorik@kippendief.biz>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMilo Kim <woogyom.kim@gmail.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Now that we have a different clock representation, switch to it.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NMichael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20160629190535.11855-15-maxime.ripard@free-electrons.com

Add uart1 pins for 4 pin (RX/TX/RTS/CTS) mode.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Move uart0 pins to sort the list of pin settings in alphabetical order.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add nodes describing the H3's usbphy and usb host controller nodes.
Signed-off-by: NReinder de Haan <patchesrdh@mveas.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add a node describing the usb-clks found on the H3.
Signed-off-by: NReinder de Haan <patchesrdh@mveas.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add a pinctrl node for mmc2 in 8 bits mode on H3 SoCs.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The H3 ir receiver is completely compatible with the one found in the A31.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add the corresponding device node for R_PIO on H3 to the dtsi. Support
for the controller was added in earlier commit.
Signed-off-by: NKrzysztof Adamski <k@japko.eu>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

APB0 is bearly mentioned in H3 User Manual and it is only setup in the
Allwinners kernel dump for CIR. I have verified experimentally that the
gate for R_PIO exists and works, though. There are probably other gates
there but I don't know their order right now and I don't have access to
their peripherals on my board to test them.

After some experiments and reviewing how this is organized on other
sunxi SoCs, I couldn't actually find any way to disable clocks for R_PIO
and they are working properly without doing anything so I assume they
are connected straight to the 24Mhz oscillator for now.
Signed-off-by: NKrzysztof Adamski <k@japko.eu>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

pinctrl-sunxi uses 3 cells to describe interrupt, not 2. It's bank
number, pin number and flags.
Signed-off-by: NKrzysztof Adamski <k@japko.eu>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Allwinner H3 is a home entertainment system oriented SoC with
four Cortex-A7 cores and a Mali-400MP2 GPU.
Signed-off-by: NJens Kuske <jenskuske@gmail.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Some boards, such as tablets, have regulators providing power to parts
of the display pipeline, like signal converters and LCD panels.

Add labels to the simplefb device nodes so that we can reference them
in the board dts files to add regulator supply properties.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

When the gpio interrupt bindings where changed to add a bank to the
specifier list, the r_pio nodes of A23/A31/A33 where not updated to
match and neither was the pio node of the A80, this fixes this.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The NMI interrupt controller is in charge of the NMI pin exposed by
the SoC to the PMIC. The PMIC signals interrupts through this.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This patch adds a device node for the Reduced Serial Bus (RSB)
controller and the defacto pinmux setting to the A23/A33 dtsi.

Since there is only one possible pinmux setting for RSB, just
set it in the dtsi.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The AHB1 gates were assumed to be identical between the A23 and the A33,
which turned out to be wrong. Move the A23 gates definition to the A23
DTSI.
Reported-by: NChen-Yu Tsai <wens@csie.org>
Reviewed-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The PWM controller has 2 outputs, with one usable pin for each.

Add a pinmux setting for the first channel. This is often used
for backlight dimming on tablets.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

A23/A33 have a PWM controller that is compatible to the one on the A20.
Add a device node for it.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The A23 and A33 gates have a non continuous set of clock IDs that are
valid. Add the clock-indices property to the DT to express this.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NMichael Turquette <mturquette@baylibre.com>

The current DTs were setting the cell size to 2, but used the default xlate
function that was assuming an interrupt cell size of 1, leading to the
second part of the cell (the flags) being ignored, while we were having an
inconsistent binding between the interrupts and gpio (that could also be
used as interrupts).

That "binding" doesn't work either with newer SoCs that have multiple irq
banks.

Now that we fixed the pinctrl driver to handle this like it should always
have been handled, convert the DT users, and while we're at it, remove the
size-cells property of PIO that is completely useless.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>