Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 23 9月, 2008 2 次提交
  3. 11 9月, 2008 2 次提交
  5. 10 9月, 2008 1 次提交
  7. 26 8月, 2008 1 次提交
  9. 19 8月, 2008 1 次提交
  11. 13 8月, 2008 1 次提交
    • T
      [IA64] Ensure cpu0 can access per-cpu variables in early boot code · 10617bbe
      由 Tony Luck 提交于 
      ia64 handles per-cpu variables a litle differently from other architectures
in that it maps the physical memory allocated for each cpu at a constant
virtual address (0xffffffffffff0000). This mapping is not enabled until
the architecture specific cpu_init() function is run, which causes problems
since some generic code is run before this point. In particular when
CONFIG_PRINTK_TIME is enabled, the boot cpu will trap on the access to
per-cpu memory at the first printk() call so the boot will fail without
the kernel printing anything to the console.

Fix this by allocating percpu memory for cpu0 in the kernel data section
and doing all initialization to enable percpu access in head.S before
calling any generic code.

Other cpus must take care not to access per-cpu variables too early, but
their code path from start_secondary() to cpu_init() is all in arch/ia64
Signed-off-by: NTony Luck <tony.luck@intel.com>
      10617bbe
  13. 05 8月, 2008 2 次提交
  15. 02 8月, 2008 1 次提交
    • T
      [IA64] Move include/asm-ia64 to arch/ia64/include/asm · 7f30491c
      由 Tony Luck 提交于 
      After moving the the include files there were a few clean-ups:

1) Some files used #include <asm-ia64/xyz.h>, changed to <asm/xyz.h>

2) Some comments alerted maintainers to look at various header files to
make matching updates if certain code were to be changed. Updated these
comments to use the new include paths.

3) Some header files mentioned their own names in initial comments. Just
deleted these self references.
Signed-off-by: NTony Luck <tony.luck@intel.com>
      7f30491c
  17. 27 7月, 2008 1 次提交
  19. 26 7月, 2008 2 次提交
    • S
      kprobes: improve kretprobe scalability with hashed locking · ef53d9c5
      由 Srinivasa D S 提交于 
      Currently list of kretprobe instances are stored in kretprobe object (as
used_instances,free_instances) and in kretprobe hash table.  We have one
global kretprobe lock to serialise the access to these lists.  This causes
only one kretprobe handler to execute at a time.  Hence affects system
performance, particularly on SMP systems and when return probe is set on
lot of functions (like on all systemcalls).

Solution proposed here gives fine-grain locks that performs better on SMP
system compared to present kretprobe implementation.

Solution:

 1) Instead of having one global lock to protect kretprobe instances
    present in kretprobe object and kretprobe hash table.  We will have
    two locks, one lock for protecting kretprobe hash table and another
    lock for kretporbe object.

 2) We hold lock present in kretprobe object while we modify kretprobe
    instance in kretprobe object and we hold per-hash-list lock while
    modifying kretprobe instances present in that hash list.  To prevent
    deadlock, we never grab a per-hash-list lock while holding a kretprobe
    lock.

 3) We can remove used_instances from struct kretprobe, as we can
    track used instances of kretprobe instances using kretprobe hash
    table.

Time duration for kernel compilation ("make -j 8") on a 8-way ppc64 system
with return probes set on all systemcalls looks like this.

cacheline              non-cacheline             Un-patched kernel
aligned patch 	       aligned patch
===============================================================================
real    9m46.784s       9m54.412s                  10m2.450s
user    40m5.715s       40m7.142s                  40m4.273s
sys     2m57.754s       2m58.583s                  3m17.430s
===========================================================

Time duration for kernel compilation ("make -j 8) on the same system, when
kernel is not probed.
=========================
real    9m26.389s
user    40m8.775s
sys     2m7.283s
=========================
Signed-off-by: NSrinivasa DS <srinivasa@in.ibm.com>
Signed-off-by: NJim Keniston <jkenisto@us.ibm.com>
Acked-by: NAnanth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Masami Hiramatsu <mhiramat@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      ef53d9c5
    • T
      [IA64] Wire up new system calls · 3e4d0cab
      由 Tony Luck 提交于 
      Six new system calls: signalfd4, eventfd2, epoll_create1,
dup3, pipe2 and inotify_init1.
Signed-off-by: NTony Luck <tony.luck@intel.com>
      3e4d0cab
  21. 25 7月, 2008 1 次提交
    • U
      flag parameters: pipe · ed8cae8b
      由 Ulrich Drepper 提交于 
      This patch introduces the new syscall pipe2 which is like pipe but it also
takes an additional parameter which takes a flag value.  This patch implements
the handling of O_CLOEXEC for the flag.  I did not add support for the new
syscall for the architectures which have a special sys_pipe implementation.  I
think the maintainers of those archs have the chance to go with the unified
implementation but that's up to them.

The implementation introduces do_pipe_flags.  I did that instead of changing
all callers of do_pipe because some of the callers are written in assembler.
I would probably screw up changing the assembly code.  To avoid breaking code
do_pipe is now a small wrapper around do_pipe_flags.  Once all callers are
changed over to do_pipe_flags the old do_pipe function can be removed.

The following test must be adjusted for architectures other than x86 and
x86-64 and in case the syscall numbers changed.

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
#include <fcntl.h>
#include <stdio.h>
#include <unistd.h>
#include <sys/syscall.h>

#ifndef __NR_pipe2
# ifdef __x86_64__
#  define __NR_pipe2 293
# elif defined __i386__
#  define __NR_pipe2 331
# else
#  error "need __NR_pipe2"
# endif
#endif

int
main (void)
{
  int fd[2];
  if (syscall (__NR_pipe2, fd, 0) != 0)
    {
      puts ("pipe2(0) failed");
      return 1;
    }
  for (int i = 0; i < 2; ++i)
    {
      int coe = fcntl (fd[i], F_GETFD);
      if (coe == -1)
        {
          puts ("fcntl failed");
          return 1;
        }
      if (coe & FD_CLOEXEC)
        {
          printf ("pipe2(0) set close-on-exit for fd[%d]\n", i);
          return 1;
        }
    }
  close (fd[0]);
  close (fd[1]);

  if (syscall (__NR_pipe2, fd, O_CLOEXEC) != 0)
    {
      puts ("pipe2(O_CLOEXEC) failed");
      return 1;
    }
  for (int i = 0; i < 2; ++i)
    {
      int coe = fcntl (fd[i], F_GETFD);
      if (coe == -1)
        {
          puts ("fcntl failed");
          return 1;
        }
      if ((coe & FD_CLOEXEC) == 0)
        {
          printf ("pipe2(O_CLOEXEC) does not set close-on-exit for fd[%d]\n", i);
          return 1;
        }
    }
  close (fd[0]);
  close (fd[1]);

  puts ("OK");

  return 0;
}
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: NUlrich Drepper <drepper@redhat.com>
Acked-by: NDavide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      ed8cae8b
  23. 22 7月, 2008 1 次提交
    • A
      sysdev: Pass the attribute to the low level sysdev show/store function · 4a0b2b4d
      由 Andi Kleen 提交于 
      This allow to dynamically generate attributes and share show/store
functions between attributes. Right now most attributes are generated
by special macros and lots of duplicated code. With the attribute
passed it's instead possible to attach some data to the attribute
and then use that in shared low level functions to do different things.

I need this for the dynamically generated bank attributes in the x86
machine check code, but it'll allow some further cleanups.

I converted all users in tree to the new show/store prototype. It's a single
huge patch to avoid unbisectable sections.

Runtime tested: x86-32, x86-64
Compiled only: ia64, powerpc
Not compile tested/only grep converted: sh, arm, avr32
Signed-off-by: NAndi Kleen <ak@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      4a0b2b4d
  25. 18 7月, 2008 3 次提交
  27. 17 7月, 2008 2 次提交
  29. 01 7月, 2008 2 次提交
  31. 26 6月, 2008 3 次提交
  33. 25 6月, 2008 2 次提交
  35. 12 6月, 2008 3 次提交
    • A
      [IA64] Update check_sal_cache_flush to use platform_send_ipi() · 3463a93d
      由 Alex Chiang 提交于 
      check_sal_cache_flush is used to detect broken firmware that drops
pending interrupts.

The old implementation schedules a timer interrupt for itself in
the future by getting the current value of the Interval Timer
Counter + 1000 cycles, waits for the interrupt to be pended, calls
SAL_CACHE_FLUSH, and finally checks to see if the interrupt is
still pending.

This implementation can cause problems for virtual machine code if
the process of scheduling the timer interrupt takes more than 1000
cycles; the virtual machine can end up sleeping for several hundred
years while waiting for the ITC to wrap around.

The fix is to use platform_send_ipi. The processor will still send
an interrupt to itself, using the IA64_IPI_DM_INT delivery mode,
which causes the IPI to look like an external interrupt. The rest
of the SAL_CACHE_FLUSH + checking to see if the interrupt is still
pending remains unchanged.

This fix has been boot tested successfully on:

	- intel tiger2
	- hp rx6600
	- hp rx5670

The rx5670 has known buggy firmware, where SAL_CACHE_FLUSH drops
pending interrupts. A boot test on this machine showed this message
on the console:

SAL: SAL_CACHE_FLUSH drops interrupts; PAL_CACHE_FLUSH will be used instead

Which proves that the self-inflicted IPI approach is viable. And
as expected, the other tested platforms correctly did not display
the warning.
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>
      3463a93d
    • F
      ACPI: handle invalid ACPI SLIT table · 39b8931b
      由 Fenghua Yu 提交于 
      This is a SLIT sanity checking patch.  It moves slit_valid() function to
generic ACPI code and does sanity checking for both x86 and ia64.  It sets up
node_distance with LOCAL_DISTANCE and REMOTE_DISTANCE when hitting invalid
SLIT table on ia64.  It also cleans up unused variable localities in
acpi_parse_slit() on x86.
Signed-off-by: NFenghua Yu <fenghua.yu@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLen Brown <len.brown@intel.com>
      39b8931b
    • S
      [IA64] perfmon: fix async exit bug · 83014699
      由 stephane eranian 提交于 
      Move the cleanup of the async queue to the close callback from the flush
callback. This avoids losing asynchronous overflow notifications when
the file descriptor is shared by multiple processes and one terminates.
Signed-off-by: NStephane Eranian <eranian@gmail.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>
      83014699
  37. 29 5月, 2008 1 次提交
  39. 28 5月, 2008 8 次提交