Channel map positions FLH, FCH, FRH duplicate positions TFL, TFC, TFR.
Both are the speakers above the front speakers (CEA uses "high" and USB
audio uses "top" nomenclature).

Since the USB audio code has used the TFx positions since v3.8
(04324ccc, "ALSA: usb-audio: add channel map support") but the HDMI
code only just started using FxH in a5b7d510 ("ALSA: hda -
hdmi: Fix channel maps with less common speakers") which is not yet in
any released kernel, standardize on TFx instead.
Signed-off-by: NAnssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Since the recent fake ELD patches, we can remove the check for AMD
HDMI in hdmi_present_sense() and decide the return value from
eld_valid value.

Suggested by Anssi Hannula.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This fixes a race condition in case several monitors are being
repolled in parallel.
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

There is a small gap between the jack detection unsolicited event and
the time the ELD is updated.  When user-space queries the HDMI ELD
immediately after receiving the notification, it might fail because of
this gap.

For avoiding such a problem, this patch tries to delay the HDMI jack
detect notification until ELD information is fully updated.  The
workaround is imperfect, but good enough as a starting point.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The function name not_share_unassigned_cvt() is opposite to what it does.
This patch renames it to intel_not_share_assigned_cvt(), and addes comments
to explain why some Intel display codecs need this workaround.
Signed-off-by: NMengdong Lin <mengdong.lin@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

NVIDIA HDMI codecs do not seem to follow the Audio Sample Packet (ASP)
channel mapping (as set by verb F32h per HDA specification 7.3.3.41)
when playing back 2-channel audio (CEA CA 0x00).

Basically this means that specifying swapped channels for stereo audio
(FR,FL) does not take effect, and e.g. this command plays back on the
wrong channel:
speaker-test -c2 -Dhdmi:CARD=NVidia,DEV=0 -m FR,FL -s1

Multichannel audio is not affected.

This issue has been confirmed to exist on codec 0x10de0015 by me and on
0x10de0040 by Juho Teperi.

Disable 2ch FL/FR channel swapping on all NVIDIA HDMI codecs that use
the standard HDA channel mapping system. Since this is a very minor
functionality loss, we err on the side of disabling it for newer codecs
as well until any future testing confirms that this issue has been
fixed.
Signed-off-by: NAnssi Hannula <anssi.hannula@iki.fi>
Helped-by: NJuho Teperi <juho.teperi@iki.fi>
Cc: Aaron Plattner <aplattner@nvidia.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

For Valleyview display codec, if an unused pin chooses an assgined converter
selected by a used pin, playback on the unused pin can also give sound to the
output device of the used pin. It's because data flows from the same convertor
to the display port of the used pin. This issue is same as Haswell.

So this patch avoids using assinged convertors for unused pins.
The related function haswell_config_cvts() is renamed for code reuse.
Signed-off-by: NMengdong Lin <mengdong.lin@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

hdmi_setup_audio_infoframe() does not set up pin and infoframe if there
is no connected sink. If a sink is connected while audio playback is
already in progress, the pin and infoframe will not be properly set up,
causing no audio or wrongly mapped audio.

On Intel Haswell codecs the hdmi_setup_audio_infoframe() is already
called again from hdmi_present_sense() when an ELD appears because
transcoder:port mapping may have changed.

Make the call non-Haswell-specific so that audio will be properly set up
if the playback was started before a sink was connected.

Tested on non-Haswell Intel HDMI codec by plugging sink in during
playback.
Signed-off-by: NAnssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Recent AMD HDMI codecs (revision ID 3 and later, 0x100300 as reported by
procfs codec#0) have a configurable ramp-up/down functionality.

The documentation ( http://www.x.org/docs/AMD/AMD_HDA_verbs_v2.pdf )
specifies that 180 ("180/256 =~ 0.7") is recommended for PCM and 0 for
non-PCM.

Apply the recommended values according to provided S/PDIF AES0 settings
since ramp-up/down does not make sense for non-PCM.

v2: adapted to hdmi_ops infrastructure

* More note from Anssi:
actually, re-reading mails reveals that Olivier didn't find the
expected difference with this setting, except for "maybe slightly
slower startup with AES0=6" (i.e. value 0, which is unexpected).

So maybe
a) it makes too unnoticiable a difference, or
b) only affects certain hardware (card and/or sink), or
c) ramp-up/down is only triggered with the MUTE bit of
   ATI_VERB_SET_MULTICHANNEL_xx which is also rev3+ specific,
   but is not presently used by the driver,
or something else.

So there's a significant chance setting ramp rate is useless for us ATM,
but probably does not do actual harm either.
Signed-off-by: NAnssi Hannula <anssi.hannula@iki.fi>
Tested-by: Olivier Langlois <olivier@trillion01.com> # v1
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

ATI/AMD HDMI codecs do not include standard HDA HDMI HBR support (which
is required for bitstreaming DTS-HD and Dolby TrueHD), instead they have
custom verbs for checking and enabling it.

Add support for the ATI/AMD HDMI HBR verbs.

The specification is available at:
http://www.x.org/docs/AMD/AMD_HDA_verbs_v2.pdf

v2: adapted to hdmi_ops infrastructure
Signed-off-by: NAnssi Hannula <anssi.hannula@iki.fi>
Tested-by: Peter Frühberger <fritsch@xbmc.org> # v1
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

ATI/AMD HDMI/DP codecs do not include standard HDA ELD (EDID-like data)
support.

In place of providing access to an ELD buffer, various vendor-specific
verbs are provided to provide the relevant information. Revision ID 3
and later (0x100300 as reported by procfs codec#X) have support for
providing more information than the previous revisions (but only if
supported by the display driver).

Generate ELD from the information provided by the vendor-specific verbs
on ATI/AMD codecs.

The specification is available at:
http://www.x.org/docs/AMD/AMD_HDA_verbs_v2.pdf

v2: moved code to hda_eld.c and cleaned it up
v3: adapted to hdmi_ops infrastructure
Signed-off-by: NAnssi Hannula <anssi.hannula@iki.fi>
Tested-by: Peter Frühberger <fritsch@xbmc.org> # v2
Tested-by: Olivier Langlois <olivier@trillion01.com> # v2
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

ATI/AMD codecs do not support all the standard HDA HDMI/DP functions,
instead various vendor-specific verbs are provided.

This commit addresses these missing functions:
- standard channel mapping support
- standard infoframe configuration support

ATI/AMD provides their own verbs that allow the following:
- setting CA for infoframe
- setting down-mix information for infoframe
- channel pair remapping
- individual channel remapping (revision ID 3+, 0x100300+)

The documentation for the verbs has now been released by AMD:
http://www.x.org/docs/AMD/AMD_HDA_verbs_v2.pdf

Add support for the ATI/AMD specific verbs and use them instead of the
generic methods on ATI/AMD codecs. This allows multi-channel PCM audio
to work.

Channel remapping is restricted to pairwise mapping on codecs with
revision ID 2 (0x100200 as reported by procfs codec#X) or lower. This
means cards up to Radeon HD7670 as far as I know. This will not affect
standard multi-channel modes since these codecs support automatic
FC-LFE swapping for HDMI.

ATI/AMD codecs do not advertise all of their supported rates, formats
and channel counts, therefore that information is forced accordingly so
that all HDMI 1.x PCM parameters are marked as supported.

Support for multiple ports is also added to patch_atihdmi so that
0x1002aa01 codecs with multiple ports will work properly when switched
back to that patch.

v2: splitted ELD emulation to a separate patch, tlv fixes
v3: adapted to the new hdmi_ops infrastructure, fixed rev3+ vendor id
Signed-off-by: NAnssi Hannula <anssi.hannula@iki.fi>
Tested-by: Peter Frühberger <fritsch@xbmc.org> # v2
Tested-by: Olivier Langlois <olivier@trillion01.com> # v2+rev3fix
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Upcoming AMD multichannel support requires many customized operations
(channel mapping, ELD, HBR) but can otherwise share most of its code
with the generic patch.

Add a local struct hdmi_ops containing customizable HDMI-specific
callbacks and move the current code to those callbacks. Functionality is
unaltered.
Signed-off-by: NAnssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

... which was introduced by the previous commit a4e9a38b, causing
build errors without CONFIG_PROC_FS.
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch adds codec ID (0x80862882) and module alias for
Valleyview2 display codec.
Signed-off-by: NMengdong Lin <mengdong.lin@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Since the lock is used primarily in patch_hdmi.c, it's better to move
it in the local struct instead of exporting in hda_eld.  The only
functions requiring the lock in hda_eld.c are proc accessors.  So in
this patch, the proc entry and its creation/deletion/accessors are
moved into patch_hdmi.c, together with the mutex lock to pin_spec
struct.

The former proc info functions are exported so that they can be called
from patch_hdmi.c.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Some per_pin fields and ELD contents might be changed dynamically in
multiple ways where the concurrent accesses are still opened in the
current code.  This patch fixes such possible races by using eld->lock
in appropriate places.
Reported-by: NAnssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Currently hdmi_setup_audio_infoframe() reprograms the HDA channel
mapping only when the infoframe is not up-to-date or the non-PCM flag
has changed.

However, when just the channel map has been changed, the infoframe may
still be up-to-date and non-PCM flag may not have changed, so the new
channel map is not actually programmed into the HDA codec.

Notably, this failing case is also always triggered when the device is
already in a prepared state and a new channel map is configured while
changing only the channel positions (for example, plain
"speaker-test -c2 -m FR,FL").

Fix that by always programming the channel map in
hdmi_setup_audio_infoframe(). Tested on Intel HDMI.
Signed-off-by: NAnssi Hannula <anssi.hannula@iki.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Allow channel map debugging for both automatic and manual channel maps,
and print CA always when updating infoframe.
Signed-off-by: NAnssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Currently the available channel maps TLV only contains channel maps that
are limited to the traditional 7.1 speakers.

Since the other HDMI channel mapping functions have been fixed to
properly handle all CEA-861-E specified speakers, allow them to be
listed.
Signed-off-by: NAnssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

For some speakers and slots the CEA slot <-> speaker assignment depends
on the used CEA Channel Allocation value.

Therefore the from_cea_slot() and to_cea_slot() helpers currently only
work correctly for the regular 7.1 speakers.

Fix them to work with all speakers, taking the re-ordered CA index as
input and adapting use sites accordingly.

This change allows manual channel mapping to actually work for all CEA
allocated speakers. Additionally, this fixes incorrect channel map
reporting in automatic channel mapping mode when an affected speaker
position is used (e.g. 6.1 map which contains an RC speaker).
Signed-off-by: NAnssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

hdmi_manual_setup_channel_mapping() and hdmi_std_setup_channel_mapping
try to assign ALSA channels to HDMI channel slots and disable (i.e.
silence) other slots.

However, they try to disable a slot by using AC_VERB_SET_CHAN_SLOT with
parameter ((alsa_ch << 8) | 0xf), while the correct parameter is
((0xf << 8) | hdmi_slot), i.e. the slot should be unassigned, not the
ALSA channel.

Fix that by actually disabling the unused slots.

Note that this bug did not cause any (reported) issues because slots
incorrectly having audio are normally ignored by a receiver if the CEA
channel allocation used does not map that slot to any speaker.
Additionally, the converter channel count configuration limits the
number of actually active channels in any case.
Signed-off-by: NAnssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Currently the converter channel count is set to the number of actual
input channels. The audio infoframe channel count field is set
similarly.

However, sometimes the used channel map does not map all input channels
to outputs. Notably, 3 channel modes (e.g. 2.1) require a dummy input
channel so there are 4 input channels. According to the HDA
specification, converter channel count should be programmed according to
the number of _active_ channels.

On Intel HDMI codecs (but not on NVIDIA), setting the converter channel
to a higher value than there are actually mapped channels to HDMI slots
will cause no audio to be output at all.

Note that the effects of this issue are currently partially masked by
other bugs that prevent the driver from actually unmapping channels in
certain cases. For example, if a 4 channel stream is first created and
prepared, it gets a FL,FR,RL,RR mapping (ALSA->HDMI slot mapping 0->0,
1->1, 2->4, 3->5). If one thereafter assigns a FR,FL,FC mapping to it,
the driver will remap 2->3 but fail to unmap 2->4 and 3->5, so there are
still 4 active channels and the issue will not trigger in this case.
These bugs will be fixed separately.

Fix the channel counts in the converter channel count field and in the
audio infoframe channel count field to match the actual number of active
channels.
Signed-off-by: NAnssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

hdmi_std_setup_channel_mapping() selects a Channel Allocation according
to the sink reported speaker mask, preferring the ALSA standard layouts.

If the channel allocation is not one of the ALSA standard layouts, the
ALSA channels are mapped directly to HDMI channels in order. However,
the function does not take into account that there a holes in the HDMI
channel map.

Additionally, the function tries to disable a slot by using
AC_VERB_SET_CHAN_SLOT with parameter ((alsa_ch << 8) | 0xf), while the
correct parameter is ((0xf << 8) | hdmi_slot), i.e. the slot should be
unassigned, not the ALSA channel.

Fix both of the issues for non-ALSA-default layouts.

Tested on Intel HDMI with a speaker mask of FL | FR | FC | RC, which
causes CA 0x06 to be selected for 4-channel audio, which causes
incorrect output (sound destined to RC goes to FC and FC goes nowhere)
without the patch.
Signed-off-by: NAnssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

hdmi_setup_fake_chmap() is supposed to set the reported channel map when
the channel map is not specified by the user.

However, the function indexes channel_allocations[] with a wrong value
and extracts the wrong nibble from hdmi_channel_mapping[], causing wrong
channel maps to be shown.

Fix those issues.

Tested on Intel HDMI to correctly generate various channel maps, for
example 3,4,14,15,7,8,5,6 (instead of incorrect 3,4,8,7,5,6,14,0) for
standard 7.1 channel audio. (Note that the side and rear channels are
reported as RL/RR and RLC/RRC, respectively, as per the CEA-861
standard, instead of the more traditional SL/SR and RL/RR.)

Note that this only fixes the layouts that only contain traditional 7.1
speakers (2.0, 2.1, 4.0, 5.1, 7.1, etc.). E.g. the rear center of 6.1
is still being shown wrongly due to an issue with from_cea_slot()
which will be fixed in a later patch.
Signed-off-by: NAnssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

BIOS can mark a pin as "no physical connection" if the port is used by an
integrated display which is not audio capable. And audio driver will overlook
such pins.

On Haswell, such a disconneted pin will keep muted and connected to the 1st
converter by default. But if the 1st convertor is assigned to a connected pin
for audio streaming. The muted disconnected pin can make the connected pin
no sound output.

So this patch avoids using assigned converters for all unused pins for Haswell,
including the disconected pins.
Signed-off-by: NMengdong Lin <mengdong.lin@intel.com>
Reviewed-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When Gfx driver reconnects a port and transcoder, the pin amplifier will
be muted. To enable sound, the pin amp need to be unmuted.

This patch
- moves pin amp unmuting from stream preparing to hdmi_setup_audio_infoframe().
  So if port:transcoder reconnection happens during stream playback, the ELDV
  unsol event can stil trigger pin's amp unmuting when re-setting up audio
  info frame.

- remove reading pin amp status before unmuting for speed-up, since pin amp
  should always be unmuted.

- rename haswell_verify_pin_D0() to haswell_verify_D0(), since the convertor
  power state is also fixed here.

This patch is mostly based on suggestion of David Henningsson.

Cc: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: NMengdong Lin <mengdong.lin@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

To apply Haswell specific fixings, this patch defines is_haswell() to check
whether a display audio codec is Haswell, to avoid explicitly checking Haswell
vendor ID everywhere.
Signed-off-by: NMengdong Lin <mengdong.lin@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When the transcoder:port mapping on Haswell HDMI/DP audio is changed
during the stream playback, the sound gets lost.  Typically this
problem is seen when the user switches the graphics mode from eDP+DP
to DP-only configuration, where CRTC 1 is used for DP in the former
while CRTC 0 is used for the latter.

The graphics controller notifies the change via the normal ELD update
procedure, so we get the intrinsic event.  For enabling the sound
again, the HDMI audio driver needs to reset the pin and set up the
audio infoframe again.

This patch achieves it by:
- keep the current status of channels and info frame setup in per_pin
  struct,
- check the reconnection in the intrinsic event handler,
- reset the pin and the re-invoke hdmi_setup_audio_infoframe()
  accordingly.

The hdmi_setup_audio_infoframe() function has been changed, too, so
that it can be invoked without passing the substream instance.

The patch is mostly based on the work by Mengdong Lin.

Cc: Mengdong Lin <mengdong.lin@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

hdmi_channel_allocation() tries to find a HDMI channel allocation that
matches the number channels in the playback stream and contains only
speakers that the HDMI sink has reported as available via EDID. If no
such allocation is found, 0 (stereo audio) is used.

Using CA 0 causes the audio causes the sink to discard everything except
the first two channels (front left and front right).

However, the sink may be capable of receiving more channels than it has
speakers (and then perform downmix or discard the extra channels), in
which case it is preferable to use a CA that contains extra channels
than to use CA 0 which discards all the non-stereo channels.

Additionally, it seems that HBR (HD) passthrough output does not work on
Intel HDMI codecs when CA is set to 0 (possibly the codec zeroes
channels not present in CA). This happens with all receivers that report
a 5.1 speaker mask since a HBR stream is carried on 8 channels to the
codec.

Add a fallback in the CA selection so that the CA channel count at least
matches the stream channel count, even if the stream contains channels
not present in the sink speaker descriptor.

Thanks to GrimGriefer at OpenELEC forums for discovering that changing
the sink speaker mask allowed HBR output.

Reported-by: GrimGriefer
Reported-by: Ashecrow
Reported-by: NFrank Zafka <kafkaesque1978@gmail.com>
Reported-by: NPeter Frühberger <fritsch@xbmc.org>
Signed-off-by: NAnssi Hannula <anssi.hannula@iki.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch adds two fields to unsolicited response, according to spec HDA040-A:
- Device Entry (bit 20:15)
- Inactive (bit 2)
and show the info in debug message.
Signed-off-by: NMengdong Lin <mengdong.lin@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch is only to allow codec proc file to expose devices list/select info
for Haswell codec pins.

Since Haswell Gfx driver cannot support DP1.2 MST now, so all pins' device list
is empty, meaning no pin is multi-streaming capaple.
Signed-off-by: NMengdong Lin <mengdong.lin@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Without the dynamic minor assignment, HDMI codec may have less PCM
instances than the number of pins, which eventually leads to Oops.
Reported-by: NStratos Karafotis <stratosk@semaphore.gr>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Vendor ID 0x10de0060 is used by a yet-to-be-named GPU chip.
Reviewed-by: NAndy Ritger <aritger@nvidia.com>
Signed-off-by: NAaron Plattner <aplattner@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Hdmi driver may not receive intrinsic event from gfx side when
it's in runtime suspend mode. There's no ELD info when exit from
runtime suspend. This patch avoid missing ELD info.
Signed-off-by: NWang Xingchao <xingchao.wang@linux.intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NWang Xingchao <xingchao.wang@linux.intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

... instead of open codes.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

For Intel Haswell HDMI codecs, the pins choose converter 0 by default.
This would cause conflict when playing audio on unused pins,the pin with
physical device connected would get audio data too.
i.e. Pin 0/1/2 default choose converter 0, pin 1 has HDMI monitor connected.
when play audio on Pin 0 or pin 2, pin 1 could get audio data too.

This patch configure unused pins to choose different converter.
Signed-off-by: NWang Xingchao <xingchao.wang@linux.intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When a selection to a converter MUX is changed in hdmi_pcm_open(), it
should be cached so that the given connection can be restored properly
at PM resume.  We need just to replace the corresponding
snd_hda_codec_write() call with snd_hda_codec_write_cache().

Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Haswell converters maybe in wrong power state before usage.
i.e. only converter 0 is in D0, converter 1/2 are in D3.
When pin choose converter 1/2, there's no audio output, this
cause dependency when playing differnt stream on pins.

AUD_PWRST  ConvertorA_Widget_Power_State_Current        D0
AUD_PWRST  ConvertorA_Widget_Power_State_Requsted       D0
AUD_PWRST  ConvertorB_Widget_Power_State_Current        D3
AUD_PWRST  ConvertorB_Widget_Power_State_Requested      D3
AUD_PWRST  ConvC_Widget_PwrSt_Curr                      D3
AUD_PWRST  ConvC_Widget_PwrSt_Req                       D3

This patch check converter's power state and set D0 if it's in D3 mode.
Signed-off-by: NWang Xingchao <xingchao.wang@linux.intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>