This adds the low level irq tracing hooks to the powerpc architecture
needed to enable full lockdep functionality.

This is partly based on Johannes Berg's initial version.  I removed
the asm trampoline that isn't needed (thus improving performance) and
modified all sorts of bits and pieces, reworking most of the assembly,
etc...
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This adds stacktrace support for powerpc, which will be needed for
lockdep.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This moves various definitions used all over the place to parse stack
frames to ptrace.h so only one definition is needed.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Lockdep found out that we can occasionally take the device-tree
lock for reading from softirq time (from rtas_token called
by the rtas real time clock code called by the NTP code),
while we take it occasionally for writing without masking
interrupts. The combination of those two can thus deadlock.

While some of those cases of interrupt read lock could be fixed
(such as caching the RTAS tokens) I figured that taking the
lock for writing is so rare (device-tree modification) that we
may as well penalize that case and allow reading from interrupts.

Thus, this turns all the writers to take the lock with irqs
masked to avoid the situation.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

A) It's not modified and so it can be made const.  const is good.
B) If one has a function that was given a const pci_bus pointer and you
want to get a pointer to its pci_controller, you'll get a warning from gcc
when you use pci_bus_to_host().  This is the right way to stop that
warning.
Signed-off-by: NTrent Piepho <tpiepho@freescale.com>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Remove the __max_memory variable, as it is not referenced anywhere
in the tree besides some code in arch/ppc.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The xics code currently has a direct and lpar variant of
xics_host_map, the only difference being which irq_chip they use.  If
we remember which irq_chip we're using we can combine these two
routines.  That also allows us to have a single irq_host_ops instead
of two.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

pseries_mpic_init_IRQ() implements the same logic as the xics code did to
find the i8259 cascade irq.  Now that we've pulled that logic out into
pseries_setup_i8259_cascade() we can use it in the mpic code.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Remove the xics references from xics_setup_8259_cascade(), and merge the
good bits from the almost identical logic in pseries_mpic_init_IRQ().
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The code in xics.c to setup the i8259 cascaded irq handler is not really
xics specific, so move it into setup.c - we will clean this up further in
a subsequent patch.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Powerpc and ppc have some code in their bitops.h that is exactly the
same as asm-generic/bitops/find.h.  Include this header instead of the
private implementation.
Signed-off-by: NAlexander van Heukelum <heukelum@fastmail.fm>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Currently USB Host isn't functional on the MPC8315E boards, for two
reasons as described below.

MPC8315 Reference Manual says:
"The USB DR unit must have the same clock ratio as the encryption core
unit, unless one of them has its clock disabled."

The encryption core also drives I2C clock, so it is enabled and is equal
to 01. That means USBDRCM should be 01 here.

Plus, according to MPC8315E-RDB schematics, USB unit consumes CLK_IN
clock from the 24.00MHz oscillator, which means we must adjust REFSEL
bits as well.

p.s.
Idially we should rework whole 83xx/usb.c code, in two steps:
1. Move SCCR code to the U-Boot;
2. Implement fsl,usb-clock property in the device tree, so usb.c could
   decide what clock exactly to use on per-board basis.

Though, today we're not in a hurry since there is just one 8315e board
out there.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

MPC8568E has 64K byte MURAM, so the size should be 0x10000, not 0xc000.
Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

As suggested by Timur Tabi, we match on the old compat node ID for one
version and warn accordingly.  If we don't do this, we plunge people who
try to use an old DTB into silent boot death with no clear indication of
what the problem is.

This patch should be removed at the beginning of the 2.6.27 dev cycle.
It is only meant to ease the transition in the short term.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Cleanups as suggested by Stephen Rothwell and Dale Farnsworth, which
incudes marking a bunch of functions static and add a vendor prefix to
the compat node check for uniqueness.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The rheap allocation function, rh_alloc, could call kmalloc with GFP_KERNEL.
This can sleep, which means you couldn't hold a spinlock while called rh_alloc.
Change all kmalloc calls to use GFP_ATOMIC so that it won't sleep.  This is
safe because only small blocks are allocated.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

* remove #cpus from mpc8544ds.dts (not used anywhere else)
* remove memreserve from mpc8568mds.dts (not needed)
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

arch/powerpc/platforms/85xx/mpc85xx_ads.c: In function ‘init_ioports’:
arch/powerpc/platforms/85xx/mpc85xx_ads.c:168: warning: initialization discards qualifiers from pointer target type
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This adds in the device tree source for the SBC8641D, based
largely on the mpc8641_hpcn.dts.  The biggest differences are
the lack of a complex IRQ mapping (since no Uli/i8259 cascade)
and the different layout of devices on the localbus node.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This adds a sample defconfig for the Wind River SBC8641D
board, with SMP, PCI and NFS root enabled.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This adds support for the Wind River SBC8641D board, based
largely on the mpc86xx_hpcn support.  The biggest difference is
the lack of the Uli and the i8259 cascade, which simplifies things.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

1. Detect (and bail out on) more conditions that violate the
assumptions of the setup code -- we assume in such cases that the device
tree is correct and reflects what the firmware did.

2. The inbound memory mask calculation was wrong.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This is needed to probe nor and nand flashes on the localbus.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

global_dbcr0 needs to be a per cpu set of save areas instead of a single
global on all processors.

Also, we switch to using DBCR0_IDM to determine if the user space app is
being debugged as its a more consistent way.  In the future we should
support features like hardware breakpoint and watchpoints which will
have DBCR0_IDM set but not necessarily DBCR0_IC (single step).
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The kconfig entry can go away once arch/ppc and references to the config in
drivers are removed.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

qe_get_brg_clk() will be used by the fsl_gtm routines.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Headers should include prototypes they use, otherwise build will
break if we use it without explicitly including io.h:

  CC      arch/powerpc/sysdev/qe_lib/gtm.o
In file included from include/asm/qe.h:20,
                 from arch/powerpc/sysdev/qe_lib/gtm.c:18:
include/asm/immap_qe.h: In function ‘immrbar_virt_to_phys’:
include/asm/immap_qe.h:480: error: implicit declaration of function ‘virt_to_phys’
make[2]: *** [arch/powerpc/sysdev/qe_lib/gtm.o] Error 1
make[1]: *** [arch/powerpc/sysdev/qe_lib] Error 2

gtm.c needs qe.h (which includes immap_qe.h) to use qe_get_brg_clk().
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

qe_muram_offset is the reverse of the qe_muram_addr, will be
used for the Freescale QE USB Host Controller driver.

This patch also moves qe_muram_addr into the qe.h header, plus
adds __iomem hints to use with sparse.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Freescale UPM can be used to adjust localbus timings or to generate
orbitrary, pre-programmed "patterns" on the external Localbus signals.
This patch implements few routines so drivers could work with UPMs in
safe and generic manner.

So far there is just one user of these routines: Freescale UPM NAND
driver.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This is needed to support other localbus peripherals, such as
NAND on FSL UPM.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

- get rid of `model = "UCC"' in the ucc nodes
  It isn't used anywhere, so remove it. If we'll ever need something
  like this, we'll use compatible property instead.
- replace last occurrences of device-id with cell-index.
  Drivers are modified for backward compatibility's sake.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NLaurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>