PE would be owned by userland, which probably request PE reset
done in host side. During the reset, we should drop the PCI
config accesses to the PE with help of flag EEH_PE_RESET.
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The names of PCI reset scopes aren't sychronized with firmware.
The patch fixes it.
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

As Anton suggested, the patch decreases the message level on EEH
initialization to avoid unnecessary messages if required. Also,
we have unified hint if any of needful RTAS calls is missed, and
then we can check /proc/device-tree to figure out the missed RTAS
calls.
Suggested-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Function pcibios_set_pcie_reset_state() can be used to do PCI
reset. PCI config access during the reset usually causes EEH
errors unexpectedly. In order to avoid the EEH error, the patch
blocks PCI config access during reset with the help of flag
EEH_PE_RESET, which is similar to what we did in EEH PE reset
path.
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The patch uses eeh_unfreeze_pe() to replace the logic clearing
frozen IO and DMA, in order to simplify the code.
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

When passing through PE to guest, that's possibly in frozen
state. The driver for the pass-through devices on guest side
can't be loaded successfully as reported. We already had one
gate in eeh_dev_open() to clear PE frozen state accordingly,
but that's not enough because the function is only called at
QEMU startup for once.

The patch adds another gate in eeh_pe_set_option() so that the
PE frozen state can be cleared at QEMU restart time.
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The function eeh_pci_enable() is called to apply various requests
to one particular PE: Enabling EEH, Disabling EEH, Enabling IO,
Enabling DMA, Freezing PE. When enabling IO or DMA on one specific
PE, we need check that IO or DMA isn't enabled previously. But
the condition used to do the check isn't completely correct because
one PE would be in DMA frozen state with workable IO path, or vice
versa.

The patch fixes the improper condition.
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The problem was reported by Carol: In the scenario of passing mlx4
adapter to guest, EEH error could be recovered successfully. When
returning the device back to host, the driver (mlx4_core.ko)
couldn't be loaded successfully because of error number -5 (-EIO)
returned from mlx4_get_ownership(), which hits offlined PCI device.
The root cause is that we missed to put the affected devices into
normal state on clearing PE isolated state right after PE reset.

The patch fixes above issue by putting the affected devices to
normal state when clearing PE isolated state in eeh_pe_state_clear().

Cc: stable@vger.kernel.org
Reported-by: NCarol L. Soto <clsoto@us.ibm.com>
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The frozen state on one specific PE is probably caused by error
injection, which is done with help of PAPR error injection registers.
According to the hardware spec, those registers should be cleared
automatically after one-shot frozen PE. However, that's not always
true, at least on P7IOC of Firebird-L. So we have to clear them
before doing PE reset to avoid recursive EEH errors at recovery
stage.
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The patch adds debugfs file (/sys/kernel/debug/powerpc/PCIxxxx/
err_injct), which accepts following formated string, to support
error injection. It will be used to support userland utility
"errinjct" in future.

  "pe_no:0:function:address:mask" - 32-bits PCI errors
  "pe_no:1:function:address:mask" - 64-bits PCI errors
Signed-off-by: NMike Qiu <qiudayu@linux.vnet.ibm.com>
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The patch introduces eeh_ops::err_inject(), which allows to inject
specified errors to indicated PE for testing purpose. The functionality
isn't support on pSeries platform. On PowerNV, the functionality
relies on OPAL API opal_pci_err_inject().
Signed-off-by: NMike Qiu <qiudayu@linux.vnet.ibm.com>
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The patch synchronizes firmware header file (opal.h) for PCI error
injection.
Signed-off-by: NMike Qiu <qiudayu@linux.vnet.ibm.com>
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

When passing through device, its PE might have been put into frozen
state. One obvious example would be: the passed PE is forced to be
offline because of hitting maximal allowed EEH errors in userland.
In that case, the frozen state won't be cleared and then the PE is
returned back to host, which might not have chance detecting and
recovering from it.

The patch adds more check when passing through device and clear the
PE frozen state if necessary.
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The PCI devices that have been passed through are enabled before
reset, we need restore to the enabled state after reset. Otherwise,
MMIO access might be issued to disabled devices after reset and
causes exceptional recursive EEH error.
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The patch adds one more option (EEH_OPT_FREEZE_PE) to set_option()
method to proactively freeze PE, which will be issued before resetting
pass-throughed PE to drop MMIO access during reset because it's
always contributing to recursive EEH error.
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The patch adds sysfs entry "eeh_pe_state". Reading on it returns
the PE's state while writing to it clears the frozen state. It's
used to check or clear the PE frozen state from userland for
debugging purpose.

The patch also replaces printk(KERN_WARNING ...) with pr_warn() in
eeh_sysfs.c
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

eeh_check_failure() is used to check frozen state of the PE which
owns the indicated I/O address. The argument "val" of the function
isn't used. The patch drops it and return the frozen state of the
PE as expected.

Cc: Vishal Mansur <vmansur@linux.vnet.ibm.com>
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Enable on DCACHE_WORD_ACCESS on ppc64le. It should work on
ppc64 and ppc32 but we need to do some testing first.

A somewhat reasonable testcase used to show the performance
improvement - a repeated stat of a 33 byte filename that
doesn't exist:

 #include <sys/types.h>
 #include <sys/stat.h>
 #include <unistd.h>

 #define ITERATIONS 10000000

 #define PATH "123456781234567812345678123456781"

 int main(void)
 {
 	unsigned long i;
 	struct stat buf;

 	for (i = 0; i < ITERATIONS; i++)
 		stat(PATH, &buf);

 	return 0;
 }

runs 27% faster on POWER8.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Use cmpb which compares each byte in two 64 bit values and
for each matching byte places 0xff in the target and 0x00
otherwise.

A simple hash_name microbenchmark:

http://ozlabs.org/~anton/junkcode/hash_name_bench.c

shows this version to be 10-20% faster than running the x86
version on POWER8, depending on the length.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

It is a rarely exercised case, so we want to have a test to ensure it
works as required.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Implement a bi-arch and bi-endian version of load_unaligned_zeropad.

Since the fallback case is so rare, a userspace test harness was used
to test this on ppc64le, ppc64 and ppc32:

http://ozlabs.org/~anton/junkcode/test_load_unaligned_zeropad.c

It uses mprotect to force a SEGV across a page boundary, and a SEGV
handler to lookup the exception tables and run the fixup routine.
It also compares the result against a normal load.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

No need for 3 functions when a single one will do.

Modify the function declaring macros to call the single function.

Reduces object code size a little:

$ size arch/powerpc/platforms/powernv/pci-ioda.o*
   text	   data	    bss	    dec	    hex	filename
  22303	   1073	   6680	  30056	   7568	arch/powerpc/platforms/powernv/pci-ioda.o.new
  22840	   1121	   6776	  30737	   7811	arch/powerpc/platforms/powernv/pci-ioda.o.old
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The return value is unnecessary and unused, so make the functions
void instead of int.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

When doing vfio passthrough a VF, the kernel will crash with following
message:

[  442.656459] Unable to handle kernel paging request for data at address 0x00000060
[  442.656593] Faulting instruction address: 0xc000000000038b88
[  442.656706] Oops: Kernel access of bad area, sig: 11 [#1]
[  442.656798] SMP NR_CPUS=1024 NUMA PowerNV
[  442.656890] Modules linked in: vfio_pci mlx4_core nf_conntrack_netbios_ns nf_conntrack_broadcast ipt_MASQUERADE ip6t_REJECT xt_conntrack bnep bluetooth rfkill ebtable_nat ebtable_broute bridge stp llc ebtable_filter ebtables ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw ip6table_filter ip6_tables iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_mangle iptable_security iptable_raw tg3 nfsd be2net nfs_acl ses lockd ptp enclosure pps_core kvm_hv kvm_pr shpchp binfmt_misc kvm sunrpc uinput lpfc scsi_transport_fc ipr scsi_tgt [last unloaded: mlx4_core]
[  442.658152] CPU: 40 PID: 14948 Comm: qemu-system-ppc Not tainted 3.10.42yw-pkvm+ #37
[  442.658219] task: c000000f7e2a9a00 ti: c000000f6dc3c000 task.ti: c000000f6dc3c000
[  442.658287] NIP: c000000000038b88 LR: c0000000004435a8 CTR: c000000000455bc0
[  442.658352] REGS: c000000f6dc3f580 TRAP: 0300   Not tainted  (3.10.42yw-pkvm+)
[  442.658419] MSR: 9000000000009032 <SF,HV,EE,ME,IR,DR,RI>  CR: 28004882  XER: 20000000
[  442.658577] CFAR: c00000000000908c DAR: 0000000000000060 DSISR: 40000000 SOFTE: 1
GPR00: c0000000004435a8 c000000f6dc3f800 c0000000012b1c10 c00000000da24000
GPR04: 0000000000000003 0000000000001004 00000000000015b3 000000000000ffff
GPR08: c00000000127f5d8 0000000000000000 000000000000ffff 0000000000000000
GPR12: c000000000068078 c00000000fdd6800 000001003c320c80 000001003c3607f0
GPR16: 0000000000000001 00000000105480c8 000000001055aaa8 000001003c31ab18
GPR20: 000001003c10fb40 000001003c360ae8 000000001063bcf0 000000001063bdb0
GPR24: 000001003c15ed70 0000000010548f40 c000001fe5514c88 c000001fe5514cb0
GPR28: c00000000da24000 0000000000000000 c00000000da24000 0000000000000003
[  442.659471] NIP [c000000000038b88] .pcibios_set_pcie_reset_state+0x28/0x130
[  442.659530] LR [c0000000004435a8] .pci_set_pcie_reset_state+0x28/0x40
[  442.659585] Call Trace:
[  442.659610] [c000000f6dc3f800] [00000000000719e0] 0x719e0 (unreliable)
[  442.659677] [c000000f6dc3f880] [c0000000004435a8] .pci_set_pcie_reset_state+0x28/0x40
[  442.659757] [c000000f6dc3f900] [c000000000455bf8] .reset_fundamental+0x38/0x80
[  442.659835] [c000000f6dc3f980] [c0000000004562a8] .pci_dev_specific_reset+0xa8/0xf0
[  442.659913] [c000000f6dc3fa00] [c0000000004448c4] .__pci_dev_reset+0x44/0x430
[  442.659980] [c000000f6dc3fab0] [c000000000444d5c] .pci_reset_function+0x7c/0xc0
[  442.660059] [c000000f6dc3fb30] [d00000001c141ab8] .vfio_pci_open+0xe8/0x2b0 [vfio_pci]
[  442.660139] [c000000f6dc3fbd0] [c000000000586c30] .vfio_group_fops_unl_ioctl+0x3a0/0x630
[  442.660219] [c000000f6dc3fc90] [c000000000255fbc] .do_vfs_ioctl+0x4ec/0x7c0
[  442.660286] [c000000f6dc3fd80] [c000000000256364] .SyS_ioctl+0xd4/0xf0
[  442.660354] [c000000f6dc3fe30] [c000000000009e54] syscall_exit+0x0/0x98
[  442.660420] Instruction dump:
[  442.660454] 4bfffce9 4bfffee4 7c0802a6 fbc1fff0 fbe1fff8 f8010010 f821ff81 7c7e1b78
[  442.660566] 7c9f2378 60000000 60000000 e93e02c8 <e8690060> 2fa30000 41de00c4 2b9f0002
[  442.660679] ---[ end trace a64ac9546bcf0328 ]---
[  442.660724]

The reason is current VF is not EEH enabled.

This patch introduces a macro to convert eeh_dev to eeh_pe. By doing so, it
will prevent converting with NULL pointer.
Signed-off-by: NWei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
CC: Michael Ellerman <mpe@ellerman.id.au>

V3 -> V4:
   1. move the macro definition from include/linux/pci.h to
      arch/powerpc/include/asm/eeh.h

V2 -> V3:
   1. rebased on 3.17-rc4
   2. introduce a macro
   3. use this macro in several other places

V1 -> V2:
   1. code style and patch subject adjustment
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

We can unindent the bulk of htab_dt_scan_page_sizes() by returning early
if the property is not found. That is nice in and of itself, but also
has the advantage of making it clear that we always return success once
we have found the ibm,segment-page-sizes property.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

"Helps debug funky firmware issues".

After:
  Starting Linux PPC64 #108 SMP Wed Aug 6 19:04:51 EST 2014
  -----------------------------------------------------
  ppc64_pft_size    = 0x1a
  phys_mem_size     = 0x200000000
  cpu_features      = 0x17fc7a6c18500249
    possible        = 0x1fffffff18700649
    always          = 0x0000000000000040
  cpu_user_features = 0xdc0065c2 0xee000000
  mmu_features      = 0x5a000001
  firmware_features = 0x00000001405a440b
  htab_hash_mask    = 0x7ffff
  -----------------------------------------------------
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

At boot we display a bunch of low level settings which can be useful to
know, and can help to spot bugs when things are fundamentally
misconfigured.

At the moment they are very widely spaced, so that we can accommodate
the line:

  ppc64_caches.dcache_line_size = 0xYY

But we only print that line when the cache line size is not 128, ie.
almost never, so it just makes the display look odd usually.

The ppc64_caches prefix is redundant so remove it, which means we can
align things a bit closer for the common case. While we're there
replace the last use of camelCase (physicalMemorySize), and use
phys_mem_size.

Before:
  Starting Linux PPC64 #104 SMP Wed Aug 6 18:41:34 EST 2014
  -----------------------------------------------------
  ppc64_pft_size                = 0x1a
  physicalMemorySize            = 0x200000000
  ppc64_caches.dcache_line_size = 0xf0
  ppc64_caches.icache_line_size = 0xf0
  htab_address                  = 0xdeadbeef
  htab_hash_mask                = 0x7ffff
  physical_start                = 0xf000bar
  -----------------------------------------------------

After:
  Starting Linux PPC64 #103 SMP Wed Aug 6 18:38:04 EST 2014
  -----------------------------------------------------
  ppc64_pft_size    = 0x1a
  phys_mem_size     = 0x200000000
  dcache_line_size  = 0xf0
  icache_line_size  = 0xf0
  htab_address      = 0xdeadbeef
  htab_hash_mask    = 0x7ffff
  physical_start    = 0xf000bar
  -----------------------------------------------------

This patch is final, no bike shedding ;)
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

We are enabling USB unconditionally which results in following build failure

drivers/built-in.o: In function `tb_drom_read':
(.text+0x1b62b70): undefined reference to `usb_speed_string'
make: *** [vmlinux] Error

Enable USB only if USB_SUPPORT is set to avoid such failures
Signed-off-by: NPranith Kumar <bobby.prani@gmail.com>
Acked-by: NAlistair Popple <alistair@popple.id.au>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Fix the following build failure

drivers/built-in.o: In function `nhi_init':
nhi.c:(.init.text+0x63390): undefined reference to `ehci_init_driver'

by adding a dependency on USB_EHCI_HCD which supplies the ehci_init_driver().

Also we need to depend on USB_OHCI_HCD similarly
Signed-off-by: NPranith Kumar <bobby.prani@gmail.com>
Acked-by: NAlistair Popple <alistair@popple.id.au>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

this patches changes some error handling logics in numa_setup_cpu(),
when cpu node is not found, so:

if the cpu is possible, but not present, -1 is kept in numa_cpu_lookup_table,
so later, if the cpu is added, we could set correct numa information for it.

if the cpu is present, then we set the first online node to
numa_cpu_lookup_table instead of 0 ( in case 0 might not be an online node? )

Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: NLi Zhong <zhong@linux.vnet.ibm.com>
Acked-by: NNishanth Aravamudan <nacc@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

As Nish suggested, it makes more sense to init the numa node informatiion
for present cpus at boottime, which could also avoid WARN_ON(1) in
numa_setup_cpu().

With this change, we also need to change the smp_prepare_cpus() to set up
numa information only on present cpus.

For those possible, but not present cpus, their numa information
will be set up after they are started, as the original code did before commit
2fabf084.

Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: NLi Zhong <zhong@linux.vnet.ibm.com>
Acked-by: NNishanth Aravamudan <nacc@linux.vnet.ibm.com>
Tested-by: NCyril Bur <cyril.bur@au1.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

With commit 2fabf084 ("powerpc: reorder per-cpu NUMA information's
initialization"), during boottime, cpu_numa_callback() is called
earlier(before their online) for each cpu, and verify_cpu_node_mapping()
uses cpu_to_node() to check whether siblings are in the same node.

It skips the checking for siblings that are not online yet. So the only
check done here is for the bootcpu, which is online at that time. But
the per-cpu numa_node cpu_to_node() uses hasn't been set up yet (which
will be set up in smp_prepare_cpus()).

So I saw something like following reported:
[    0.000000] CPU thread siblings 1/2/3 and 0 don't belong to the same
node!

As we don't actually do the checking during this early stage, so maybe
we could directly call numa_setup_cpu() in do_init_bootmem().

Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: NLi Zhong <zhong@linux.vnet.ibm.com>
Acked-by: NNishanth Aravamudan <nacc@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The size field of the op.type word is now the total number of bytes
to be loaded or stored.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This extends the instruction emulation done by analyse_instr() and
emulate_step() to handle a few more instructions that are found in
the kernel.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This splits out the instruction analysis part of emulate_step() into
a separate analyse_instr() function, which decodes the instruction,
but doesn't execute any load or store instructions.  It does execute
integer instructions and branches which can be executed purely by
updating register values in the pt_regs struct.  For other instructions,
it returns the instruction type and other details in a new
instruction_op struct.  emulate_step() then uses that information
to execute loads, stores, cache operations, mfmsr, mtmsr[d], and
(on 64-bit) sc instructions.

The reason for doing this is so that the KVM code can use it instead
of having its own separate instruction emulation code.  Possibly the
alignment interrupt handler could also use this.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

In commit e6a6928c "of/fdt: Convert FDT functions to use libfdt",
the kernel stopped supporting old flat device tree formats. The minimum
supported version is now 0x10.

There was a checking function added, early_init_dt_verify(), but it's
not called on powerpc.

The result is, if you boot with an old flat device tree, the kernel will
fail to parse it correctly, think you have no memory etc. and hilarity
ensues.

We can't really fix it, but we can at least catch the fact that the
device tree is in an unsupported format and panic(). We can't call
BUG(), it's too early.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

On PowerNV platforms, when a CPU is offline, we put it into nap mode.
It's possible that the CPU wakes up from nap mode while it is still
offline due to a stray IPI.  A misdirected device interrupt could also
potentially cause it to wake up.  In that circumstance, we need to clear
the interrupt so that the CPU can go back to nap mode.

In the past the clearing of the interrupt was accomplished by briefly
enabling interrupts and allowing the normal interrupt handling code
(do_IRQ() etc.) to handle the interrupt.  This has the problem that
this code calls irq_enter() and irq_exit(), which call functions such
as account_system_vtime() which use RCU internally.  Use of RCU is not
permitted on offline CPUs and will trigger errors if RCU checking is
enabled.

To avoid calling into any generic code which might use RCU, we adopt
a different method of clearing interrupts on offline CPUs.  Since we
are on the PowerNV platform, we know that the system interrupt
controller is a XICS being driven directly (i.e. not via hcalls) by
the kernel.  Hence this adds a new icp_native_flush_interrupt()
function to the native-mode XICS driver and arranges to call that
when an offline CPU is woken from nap.  This new function reads the
interrupt from the XICS.  If it is an IPI, it clears the IPI; if it
is a device interrupt, it prints a warning and disables the source.
Then it does the end-of-interrupt processing for the interrupt.

The other thing that briefly enabling interrupts did was to check and
clear the irq_happened flag in this CPU's PACA.  Therefore, after
flushing the interrupt from the XICS, we also clear all bits except
the PACA_IRQ_HARD_DIS (interrupts are hard disabled) bit from the
irq_happened flag.  The PACA_IRQ_HARD_DIS flag is set by power7_nap()
and is left set to indicate that interrupts are hard disabled.  This
means we then have to ignore that flag in power7_nap(), which is
reasonable since it doesn't indicate that any interrupt event needs
servicing.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

I ran some tests to compare hash_64 using shifts and multiplies.
The results:

POWER6:	~2x slower
POWER7: ~2x faster
POWER8: ~2x faster

Now we have a proper config option, select
CONFIG_ARCH_HAS_FAST_MULTIPLIER on POWER7 and POWER8.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This allows the user to build a kernel targeted at POWER8
(ie gcc -mcpu=power8).
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

When removing a cpu, this patch makes sure that values
gotten from or passed to firmware are in the correct
endian format.
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>