Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 18 2月, 2009 4 次提交
  3. 17 2月, 2009 3 次提交
  5. 13 2月, 2009 1 次提交
    • T
      ASoC: add additional controls to the CS4270 codec driver · d5e9ba1d
      由 Timur Tabi 提交于 
      Update the CS4270 codec driver to allow applications to use the mixer to
control Digital Loopback, Soft Ramp, Zero Cross, Popguard, and Auto-Mute.
Soft Ramp, Zero Cross, and Auto-Mute are disabled by the driver when it first
initializes the hardware, but these features either don't work or interfere
with normal ALSA behavior.  However, they can now be re-enabled by an
application if desired.

Remove CONFIG_SND_SOC_CS4270_HWMUTE and always allow ASoC to control the mute
bits.  The driver previously and erroneously assumed that these bits
control only external muting circuitry, but they also control internal
muting circuitry, so they should always be used.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
      d5e9ba1d
  7. 10 2月, 2009 2 次提交
  9. 06 2月, 2009 2 次提交
  11. 04 2月, 2009 2 次提交
  13. 03 2月, 2009 3 次提交
  15. 31 1月, 2009 1 次提交
  17. 30 1月, 2009 1 次提交
    • T
      ASoC: fix initialization order of the CS4270 codec driver · 04eb093c
      由 Timur Tabi 提交于 
      ASoC codec drivers typically serve two masters: the I2C bus and ASoC itself.
When a codec driver registers with ASoC, a probe function is called.  Most
codec drivers call ASoC first, and then register with the I2C bus in the ASoC
probe function.

However, in order to support multiple codecs on one board, it's easier if the
codec driver is probed via the I2C bus first.  This is because the call to
i2c_add_driver() can result in the I2C probe function being called multiple
times - once for each codec.  In the current design, the driver registers
once with ASoC, and in the ASoC probe function, it calls i2c_add_driver().
The results in the I2C probe function being called multiple times before the
driver can register with ASoC again.

The new design has the driver call i2c_add_driver() first.  In the I2C probe
function, the driver registers with ASoC.  This allows the ASoC probe function
to be called once per I2C device.

Also add code to check if the I2C probe function is called more than once,
since that is not supported with the current ASoC design.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
      04eb093c
  19. 29 1月, 2009 2 次提交
    • P
      ASoC: TWL4030: Add analog loopback support · 7393958f
      由 Peter Ujfalusi 提交于 
      This patch adds the analog loopback/bypass support for twl4030 codec.

Details for the implementation:
It seams that the analog loopback needs the DAC powered on on the channel,
where the loopback is selected. The switch for the DACs has been moved from
the DAPM_DAC to the "Analog XX Playback Mixer". In this way the DAC will be
powered while the audio playback is used or/and the loopback is enabled for
the channel.

The twl4030 codec powering has been reworked. Now the codec will be powered as
long as it does not receives the SND_SOC_BIAS_OFF event. The exceptions are
when the given change in the registers needs the codec power down/up cycle in
order to take effect. Otherwise the codec is on.

When the codec enters to STANDBY state and none of the loopback paths are
enabled, than the amplifiers, which are no in the DAPM path are forced to turn
off and the PLL is disabled. When playback/capture starts the disabled gains
are restored and the PLL is enabled.

When one of the loopback enabled in STANDBY mode, the disabled gains are
restored and the PLL is enabled also.

In short: the codec always goes to the lowest power state based on the
bias_level and the bypass_state.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
      7393958f
    • M
      ASoC: Fix null string usage with WM8753 DAIs · 9e70c1f0
      由 Mark Brown 提交于 
      The WM8753 driver multiplexes the DAI structures it exposes to the
outside world, leaving them uninitialised until the codec probes.  Since
the DAI name is used during the registration and setup process provide a
dummy name.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
      9e70c1f0
  21. 27 1月, 2009 6 次提交
  23. 24 1月, 2009 1 次提交
  25. 23 1月, 2009 4 次提交
  27. 21 1月, 2009 1 次提交
  29. 20 1月, 2009 1 次提交
  31. 17 1月, 2009 2 次提交
  33. 09 1月, 2009 3 次提交
  35. 08 1月, 2009 1 次提交