Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 08 3月, 2015 2 次提交
  3. 07 3月, 2015 2 次提交
  5. 05 3月, 2015 1 次提交
  7. 02 3月, 2015 2 次提交
  9. 21 2月, 2015 1 次提交
  11. 06 2月, 2015 1 次提交
  13. 27 1月, 2015 2 次提交
  15. 16 1月, 2015 3 次提交
  17. 14 1月, 2015 2 次提交
  19. 13 1月, 2015 1 次提交
  21. 16 12月, 2014 2 次提交
  23. 13 12月, 2014 1 次提交
    • C
      net/macb: add TX multiqueue support for gem · 02c958dd
      由 Cyrille Pitchen 提交于 
      gem devices designed with multiqueue CANNOT work without this patch.

When probing a gem device, the driver must first prepare and enable the
peripheral clock before accessing I/O registers. The second step is to read the
MID register to find whether the device is a gem or an old macb IP.
For gem devices, it reads the Design Configuration Register 6 (DCFG6) to
compute to total number of queues, whereas macb devices always have a single
queue.
Only then it can call alloc_etherdev_mq() with the correct number of queues.
This is the reason why the order of some initializations has been changed in
macb_probe().
Eventually, the dedicated IRQ and TX ring buffer descriptors are initialized
for each queue.

For backward compatibility reasons, queue0 uses the legacy registers ISR, IER,
IDR, IMR, TBQP and RBQP. On the other hand, the other queues use new registers
ISR[1..7], IER[1..7], IDR[1..7], IMR[1..7], TBQP[1..7] and RBQP[1..7].
Except this hardware detail there is no real difference between queue0 and the
others. The driver hides that thanks to the struct macb_queue.
This structure allows us to share a common set of functions for all the queues.

Besides when a TX error occurs, the gem MUST be halted before writing any of
the TBQP registers to reset the relevant queue. An immediate side effect is
that the other queues too aren't processed anymore by the gem.
So macb_tx_error_task() calls netif_tx_stop_all_queues() to notify the Linux
network engine that all transmissions are stopped.

Also macb_tx_error_task() now calls spin_lock_irqsave() to prevent the
interrupt handlers of the other queues from running as each of them may wake
its associated queue up (please refer to macb_tx_interrupt()).

Finally, as all queues have previously been stopped, they should be restarted
calling netif_tx_start_all_queues() and setting the TSTART bit into the Network
Control Register. Before this patch, when dealing with a single queue, the
driver used to defer the reset of the faulting queue and the write of the
TSTART bit until the next call of macb_start_xmit().
As explained before, this bit is now set by macb_tx_error_task() too. That's
why the faulting queue MUST be reset by setting the TX_USED bit in its first
buffer descriptor before writing the TSTART bit.

Queue 0 always exits and is the lowest priority when other queues are available.
The higher the index of the queue is, the higher its priority is.

When transmitting frames, the TX queue is selected by the skb->queue_mapping
value. So queue discipline can be used to define the queue priority policy.
Signed-off-by: NCyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      02c958dd
  25. 12 12月, 2014 1 次提交
  27. 10 12月, 2014 1 次提交
  29. 26 11月, 2014 1 次提交
  31. 20 10月, 2014 1 次提交
  33. 04 10月, 2014 1 次提交
  35. 27 9月, 2014 1 次提交
  37. 14 9月, 2014 1 次提交
  39. 25 7月, 2014 5 次提交
  41. 06 5月, 2014 5 次提交
  43. 25 4月, 2014 1 次提交
  45. 15 4月, 2014 1 次提交
  47. 08 4月, 2014 1 次提交