Helps debug multi-VIF scenarios.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some stats for /proc/net/wireless (and wext in general) are not
being set.  This patch addresses a few of those with values easily
obtained from mac80211 core.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Old messages didn't mention the device in question.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reverts commit 5a254ffe.

The commit failed to take into account that allocated wireless devices
(wiphys) are not added into the device list upon allocation, but only
when they are registered. Therefore, it opened up a race between
allocating and registering a name, so that if two processes allocate and
register concurrently ("alloc, alloc, register, register" rather than
"alloc, register, alloc, register") the code will attempt to use the
same name twice.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add required suspend/resume support to prevent the SDIO
core from removing our card completely during system suspend.
Signed-off-by: NOhad Ben-Cohen <ohad@wizery.com>
Tested-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>

Enable runtime PM for the wl1271 SDIO device.

We request power whenever the WLAN interface is brought up,
and release it after the WLAN interface is taken down.

As a result, power is released immediately after probe returns,
since at that point power has not been explicitly requested yet
(i.e. the WLAN interface is still down).
Signed-off-by: NOhad Ben-Cohen <ohad@wizery.com>
Acked-by: NLuciano Coelho <luciano.coelho@nokia.com>
Tested-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>

6000g2 devices need to have temperature offset calibration. The runtime
uCode needs to receive the calibration results just like BB and LO
calibration. To do this, driver reads the offset value from NVM and send
it to uCode after runtime uCode is alive.
Signed-off-by: NShanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn driver uses the IWL_MAX_STANDARD_PHY_CALIBRATE_TBL_SIZE
as the chain noise reset calibration index and
IWL_MAX_STANDARD_PHY_CALIBRATE_TBL_SIZE+1 as the chain noise gain
calibration index, if not specified by the TLV value in the new
firmware format.

However, this is broken if we need to add more calibrations like
the temperature offset calibration because we increased
IWL_MAX_STANDARD_PHY_CALIBRATE_TBL_SIZE by 1.

To fix this issue, define IWL_DEFAULT_STANDARD_PHY_CALIBRATE_TBL_SIZE
and use it as the calibration index instead. We still keep the
IWL_MAX_STANDARD_PHY_CALIBRATE_TBL_SIZE as a sanity check for
the TLV value given by ucode.
Signed-off-by: NShanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

For experimental uCode, it should work with the driver
if driver has experimental uCode support option enabled;
remove the API version checking.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The recent scanning code shuffle accidentally
moved the SCAN_HW bit setting _after_ the PAN
parameters are modified, which means that they
don't take the scan into account -- fix that.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The function is used exactly once, and the caller
doesn't even need the special check, it can be
simplified to a simple bit check.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

A number of declarations in iwl-core.h should
be in agn specific files, and also rename the
iwl-calib.h file to iwl-agn-calib.h to better
reflect that it belongs to agn.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Since all devices share the same operation here,
there's no need to call it indirectly.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The set_pwr_src operation is only ever used from
within the same sub-driver that it is declared
in, so it can just be called directly instead of
being an operation. Also, it is never called to
set the power source to V_aux, so change the two
functions accordingly (but keep the V_aux code
for documentation purposes in a comment).
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

This operation is only ever called from set_hw_params,
which is also already based on the config/ops, so that
there's no need to have a separate set_ct_kill op and
we can just call the right ct_threshold function.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The iwl_dump_fh function is only used
by the agn module, so it can be there
instead of being exported by the core.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The iwl_dump_csr function is only used
within the agn module, so it can be
moved there instead of being exported
by the core.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The iwl_toggle_tx_ant function is only used
by agn code, so it can be moved into the
agn module instead of being exported from
the core.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Code and data related to agn bitrates can be
part of the agn module rather than being in
the core module.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

A number of exports, especially related to
thermal throttling, are unnecessary because
the code lives in the same module that it
is used in, so remove them.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The code to print out TX failure reasons is
AGN specific, so it can be in the AGN module.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

By duplicating a little bit of code between 3945
and agn, we can move a lot of code into an agn
specific station management file and thus reduce
the amount of code in core that is dead to 3945.

before:
   text	   data	    bss	    dec	    hex	filename
 212886	   3872	     96	 216854	  34f16	iwlcore.ko
 620542	  10448	    304	 631294	  9a1fe	iwlagn.ko
 314013	   3264	    196	 317473	  4d821	iwl3945.ko

after:
   text	   data	    bss	    dec	    hex	filename
 202857	   3872	     92	 206821	  327e5	iwlcore.ko
 629102	  10448	    308	 639858	  9c372	iwlagn.ko
 314240	   3264	    196	 317700	  4d904	iwl3945.ko

delta:
 -10029   iwlcore.ko
   8560   iwlagn.ko
    227   iwl3945.ko

so it's a net win even if you have both loaded,
likely because a lot of EXPORT_SYMBOLs go away.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

All drivers share the same implementation, so
there's no need to call this via a function
pointer nor to export it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Rename iwl_mac_beacon_update to iwlcore_beacon_update
and make the calling convention a bit different. The
old name with _mac_ indicated that it was a mac80211
callback, but that's no longer true.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The core module doesn't need to carry around
the code for chain settings that is used for
HT drivers (agn) only.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

There's no need to go via the indirect function
call from within the 3945 subdriver.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The different drivers need to do different things
after a scan, so create a post_scan hook to allow
them to do this.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

iwl_commit_rxon really should be named
iwlagn_commit_rxon, so rename it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The following commit removed DISABLE_REGWRITE_BUFFER ops. The unnecessary
REGWRITE_BUFFER_FLUSH was not removed properly which is causing failure on
hw reset.

Author: Felix Fietkau <nbd@openwrt.org>
Date:   Tue Oct 5 12:03:42 2010 +0200

    ath9k_hw: clean up register write buffering
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There's no need for the WDS peer address
to not be const, so make it const.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Bill Jordan's patch to allow setting the WDS
peer crossed with my patch removing all the
boilerplate code in nl80211, and consequently
he didn't make use of it yet. Fix that.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The recent scan overhaul broke locking
because now we can jump to code that
attempts to unlock, while we don't have
the mutex held. Fix this by holding the
mutex around all the relevant code.
Reported-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the NVS/INI-parameters for the driver/firmware there is the FEM
(front end module) selection option, which may configure the hardware FEM
via autodetection or manual selection. So far, there has been support for
manual selection only.

Add support for FEM autodetection.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Merge branch 'wireless-next-2.6' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-2.6

This reverts commit 5ed3bc72.

It turns-out that not all drivers are calling ieee80211_tx_status from a
compatible context.  Revert this for now and try again later...
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reverts commit 030725d2.

This commit relies on commit 5ed3bc72
("mac80211: use netif_receive_skb in ieee80211_tx_status callpath")
Unfortunately not all drivers are calling ieee80211_tx_status from a
compatible context, so that commit needs to be reverted in 2.6.36.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Adding MODULE_FIRMWARE define for 130 series of devices
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

130 series device should use firmware name with 130 in it.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>