Basic XDP drop support for ixgbe. Uses READ_ONCE/xchg semantics on XDP
programs instead of RCU primitives as suggested by Daniel Borkmann and
Alex Duyck.

v2: fix the build issues seen w/ XDP when page sizes are larger than 4K
    and made minor fixes based on feedback from Jakub Kicinski
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Acked-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A recent firmware change fixed an issue to acquire the PHY semaphore before
accessing PHY registers. This led to a case where  SW can issue a device
reset clearing the MDIO registers. This patch makes SW acquire the PHY
semaphore before issuing a device reset.
Signed-off-by: NPaul Greenwalt <paul.greenwalt@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

I just found that when we had changed the Rx path to check for length
instead of the DD bit we introduced an issue in ixgbe_dump since we were no
longer clearing the status bits.

To correct this I am updating ixgbe_dump to look for the length bits in the
descriptor since that is what we are using in the Rx path.

Fixes: c3630cc4 ("ixgbe: Use length to determine if descriptor is done")
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch increases the headroom allocated when using build_skb on a
system with 4K pages.  Specifically the breakdown of headroom versus cache
size is as follows:
    L1 Cache Size           Headroom
    64                      192
    64, NET_IP_ALIGN == 2   194
    128                     128
    128, NET_IP_ALIGN == 2  130
    256                     512
    256, NET_IP_ALIGN == 2  258

I stopped at supporting only a cache line size of 256 as that was the
largest cache size I could find supported in the kernel.

With this we are guaranteeing at least 128 bytes of headroom to spare in
the frame.  This should be enough for us to insert a couple of IPv6 headers
if needed which is likely enough room for anything XDP should need.

I'm leaving the padding for systems with pages larger than 4K unmodified
for now.  XDP currently isn't really setup to work on those types of
systems so we can cross that bridge when we get there.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We did not have a check in place for MMNGC.MNG_VETO when setting up link
on X550EM_X KR devices which resulted in link loss for the BMC when
loading the driver.

This patch adds a check for ixgbe_check_reset_blocked() in setup_link()
since in that case there is no PHY reset function.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove the Marvell 1145 PHY define as we have never had a device that
supports it and have no plan to in the future.  The existence of this
define has caused confusing on whether or not this PHY was supported
by ixgbe.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Avoid setting adapter->num_vfs early in the init code path when
using the max_vfs module parameter by passing it to ixgbe_enable_sriov()
as a function parameter.

This fixes an issue where if we failed to allocate vfinfo in
__ixgbe_enable_sriov() the driver will crash with NULL pointer in
ixgbe_disable_sriov() when attempting to free the vfinfo struct based
on adapter->num_vfs. Also it cleans up the assignment of adapter->num_vfs
since now it will only be set in __ixgbe_enable_sriov() and cleared in
ixgbe_disable_sriov().
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since we exit at the end of the block, we can save a level of
indentation by performing an early return, and make the next several
sections of code more legible, with fewer 80 character line breaks.

Also moved allocating vfinfo at the beginning and the notification
for enabling SRIOV at the end of the function when we know that it
will succeed.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the code allocating memory for list of MAC addresses that
the VFs can use for MACVLAN into its own function.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add default setting for mac->ops.setup_link on x550em_a MAC types.
This fixes a link issue on KR parts.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We forgot to indicate some of the supported speed on the X553
backplane.  This patch attempts to correct for that.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch add support for X552 XFI backplane interface.  The XFI
backplane requires a custom tuned link.  HW/FW owns the link config
for XF backplane and SW must not interfere with it.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The initial patches supporting X553 sgmii forgot some details.  This patch
should cover those missing spots.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The KX4 PHY is configured by the NVM.  Currently, the driver is overwriting
the config; remove the code associated with KX4 configuration.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NKrishneil Singh  <krishneil.k.singh@intel.com>

As pr_cont output can be interleaved by other processes,
using pr_cont should be avoided where possible.

Miscellanea:

- Use a temporary pointer to hold the next descriptions and
  consolidate the pr_cont uses
- Use the temporary buffer to hold the 8 u32 register values and
  emit those in a single go
- Coalesce formats and logging neatening around those changes
- Fix a defective output for the rx ring entry description when
  also emitting rx_buffer_info data

This reduces overall object size a tiny bit too.

$ size drivers/net/ethernet/intel/ixgbe/*.o*
   text	   data	    bss	    dec	    hex	filename
  62167	    728	     12	  62907	   f5bb	drivers/net/ethernet/intel/ixgbe/ixgbe_main.o.new
  62273	    728	     12	  63013	   f625	drivers/net/ethernet/intel/ixgbe/ixgbe_main.o.old
Signed-off-by: NJoe Perches <joe@perches.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When DCB is enabled, add checks to ensure creation of number of VF's is
valid based on the traffic classes configured by the device.
Signed-off-by: NUsha Ketineni <usha.k.ketineni@intel.com>
Tested-by: NRonald Bynoe <ronald.j.bynoe@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There was a typo that I had left in the code comments for the igb and ixgbe
functions that enabled build_skb support.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The configurable priority to traffic class mapping and the user specified
queue ranges are used to configure the traffic class, overriding the
hardware defaults when the 'hw' option is set to 0. However, when the 'hw'
option is non-zero, the hardware QOS defaults are used.

This patch makes it so that we can pass the data the user provided to
ndo_setup_tc. This allows us to pull in the queue configuration if the
user requested it as well as any additional hardware offload type
requested by using a value other than 1 for the hw value.

Finally it also provides a means for the device driver to return the level
supported for the offload type via the qopt->hw value. Previously we were
just always assuming the value to be 1, in the future values beyond just 1
may be supported.
Signed-off-by: NAmritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.

As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On architectures that have a cache line size larger than 64 Bytes we start
running into issues where the amount of headroom for the frame starts
shrinking.

The size of skb_shared_info on a system with a 64B L1 cache line size is
320.  This increases to 384 with a 128B cache line, and 512 with a 256B
cache line.

In addition the NET_SKB_PAD value increases as well consistent with the
cache line size.  As a result when we get to a 256B cache line as seen on
the s390 we end up 768 bytes used by padding and shared info leaving us
with only 1280 bytes to use for data storage.  On architectures such as
this we should default to using 3K Rx buffers out of a 8K page instead of
trying to do 1.5K buffers out of a 4K page.

To take all of this into account I have added one small check so that we
compare the max_frame to the amount of actual data we can store.  This was
already occurring for igb, but I had overlooked it for ixgbe as it doesn't
have strict limits for 82599 once we enable jumbo frames.  By adding this
check we will automatically enable 3K Rx buffers as soon as the maximum
frame size we can handle drops below the standard Ethernet MTU.

I also went through and fixed one small typo that I found where I had left
an IGB in a variable name due to a copy/paste error.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently ixgbe_set_rxfh() updates the rss_key copy in the driver
memory, but does not push the new value into the h/w. This commit
add a new helper for the latter operation and call it in
ixgbe_set_rxfh(), so that the h/w rss key value can be really
updated via ethtool.
Signed-off-by: NPaolo Abeni <pabeni@redhat.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix typos and add the following to the scripts/spelling.txt:

  applys||applies

The "applyes" in drivers/video/fbdev/aty/radeon_monitor.c is a different
pattern but it was fixed in this commit.  The "This functions" in the
same line was fixed as well.

Link: http://lkml.kernel.org/r/1481573103-11329-24-git-send-email-yamada.masahiro@socionext.comSigned-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch makes it so that we don't need to bother with clearing the
memory out for the descriptor rings.  The general idea is to only free
buffers associated with buffers in use which are located between the
next_to_clean and next_to_use or next_to_alloc values.  Everything outside
of those regions can be safely ignored since they should have no buffers
associated with them.

The advantage to doing things this way is that is should speed up bring-up
and tear-down of the rings.  Specifically we can avoid the 512 or more
cycles required to memset the rings in tear-down.  In the bring-up phase we
then clear the memory as a part of initialization.  The general idea is
that the clearing in initialization can act as a prefetch of sorts for the
buffer info structures so they are in the local CPU when we go to populate
them.  This should help to improve overall time needed to perform a
suspend/resume.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds build_skb support to the Rx path.  There are several
advantages to this change.

1.  It avoids the memcpy and skb->head allocation for small packets which
    improves performance by about 5% in my tests.
2.  It avoids the memcpy, skb->head allocation, and eth_get_headlen
    for larger packets improving performance by about 10% in my tests.
3.  For VXLAN packets it allows the full header to be in skb->data which
    improves the performance by as much as 30% in some of my tests.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since there are potential drawbacks to the new Rx allocation approach I
thought it best to add a "chicken bit" so that we can turn the feature off
if in the event that a problem is found.

It also provides a means of validating the legacy Rx path in the event that
we are forced to fall back.  At some point in the future when we are
convinced we don't need it anymore we might be able to drop the legacy-rx
flag.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for providing a buffer with headroom and tailroom
to allow for shared info, NET_SKB_PAD, and NET_IP_ALIGN.  With this
combined with the DMA changes we can start using build_skb to build frames
around an incoming Rx buffer instead of having to memcpy the headers.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We are going to be expanding the number of Rx paths in the driver.  Instead
of duplicating all that code I am pulling it apart into separate functions
so that we don't have so much code duplication.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change makes it so that we use the length of the packet instead of the
DD status bit to determine if a new descriptor is ready to be processed.
The obvious advantage is that it cuts down on reads as we don't really even
need the DD bit if going from a 0 to a non-zero value on size is enough to
inform us that the packet has been completed.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In order to support build_skb with jumbo frames it will be necessary to use
3K buffers for the Rx path with 8K pages backing them.  This is needed on
architectures that implement 4K pages because we can't support 2K buffers
plus padding in a 4K page.

In the case of systems that support page sizes larger than 4K the 3K
attribute will only be applied to FCoE as we can fall back to using just 2K
buffers and adding the padding.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Batch the page count updates instead of doing them one at a time.  By doing
this we can improve the overall performance as the atomic increment
operations can be expensive due to the fact that on x86 they are locked
operations which can cause stalls.  By doing bulk updates we can
consolidate the stall which should help to improve the overall receive
performance.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for DMA_ATTR_SKIP_CPU_SYNC and
DMA_ATTR_WEAK_ORDERING.  By enabling both of these for the Rx path we are
able to see performance improvements on architectures that implement either
one due to the fact that page mapping and unmapping only has to sync what
is actually being used instead of the entire buffer.  In addition by
enabling the weak ordering attribute enables a performance improvement for
architectures that can associate a memory ordering with a DMA buffer such
as Sparc.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

On some platforms, syncing a buffer for DMA is expensive. Rather than
sync the whole 2K receive buffer, only synchronise the length of the
frame, which will typically be the MTU, or a much smaller TCP ACK.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch consolidates the code for the ixgbe driver so that it is more
inline with what is already in igb.  The general idea is to just
consolidate functions that represent logical steps in the Rx process so we
can later update them more easily.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Update the driver version to reflect the new devices that it
supports.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since dcbnl_ops is global, it should be prefixed by ixgbe_
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Though not advertised through ethtool, if the link partner advertises a
2.5Gb or 5Gb connection, and the adapter supports it, allow the speed to be
used.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In linux-4.5, busy polling was implemented in core
NAPI stack, meaning that all custom implementation can
be removed from drivers.

Not only we remove lot's of code, we also remove one lock
operation in fast path, and allow GRO to do its job.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The network stack no longer uses the last_rx member of struct net_device
since the bonding driver switched to use its own private last_rx in
commit 9f242738 ("bonding: use last_arp_rx in slave_last_rx()").

However, some drivers still (ab)use the field for their own purposes and
some driver just update it without actually using it.

Previously, there was an accompanying comment for the last_rx member
added in commit 4dc89133 ("net: add a comment on netdev->last_rx")
which asked drivers not to update is, unless really needed. However,
this commend was removed in commit f8ff080d ("bonding: remove
useless updating of slave->dev->last_rx"), so some drivers added later
on still did update last_rx.

Remove all usage of last_rx and switch three drivers (sky2, atp and
smc91c92_cs) which actually read and write it to use their own private
copy in netdev_priv.

Compile-tested with allyesconfig and allmodconfig on x86 and arm.

Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Acked-by: NEric Dumazet <edumazet@google.com>
Reviewed-by: NJay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Relax ordering(RO) is one feature of 82599 NIC, to enable this feature can
enhance the performance for some cpu architecure, such as SPARC and so on.
Currently it only supports one special cpu architecture(SPARC) in 82599
driver to enable RO feature, this is not very common for other cpu architecture
which really needs RO feature.
This patch add one common config CONFIG_ARCH_WANT_RELAX_ORDER to set RO feature,
and should define CONFIG_ARCH_WANT_RELAX_ORDER in sparc Kconfig firstly.
Signed-off-by: NMao Wenan <maowenan@huawei.com>
Reviewed-by: NAlexander Duyck <alexander.duyck@gmail.com>
Reviewed-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.

Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>