Re-use bitmap_fill() instead of open coded loop for setting an area of
bits in a bitmap.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

There is no point in keeping an address in the file since it's subject
to change.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Simply join string literals back for better maintenance and debugging.

No functional changes intended.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The PNP ACPI driver parses ACPI interrupt resource but not
GpioInt resource. When the firmware passes GpioInt resource
for IRQ the PNP ACPI driver ignores it and hence the interrupt for
the particular driver will not work.
One such example is 8042 keyboard which uses PNP driver for obtaining
the interrupt resource. On Intel Braswell project GpioInt is used
instead of interrupt resource and the keyboard driver fails to
register interrupt.
Fix the issue by parsing GpioInt resource type.
Signed-off-by: NJagadish Krishnamoorthy <jagadish.krishnamoorthy@intel.com>
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>
[Fixed a parenthesis coding style thing]
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The helper does retrieve pointer to struct acpi_resource_gpio from
struct acpi_resource if it represents GpioInt() resource.

It will be used by PNP code later on.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This allows ACPI GPIO code to modify flags based on
ACPI GpioIo() / GpioInt() resources.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The helper function acpi_gpio_to_gpiod_flags() will be used later to configure
pin properly whenever it's requested.

While here, introduce a checking error code returned by gpiod_configure_flags()
and bail out if it's not okay.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Documentation lacks of explanation how we actually use device properties
for GPIO resources.

Add a section to the documentation about that.
Suggested-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

If we pass connection ID to the both functions and at the same time
acpi_can_fallback_to_crs() returns false we will get different results,
i.e. the number of GPIO resources returned by acpi_gpio_count() might be
not correct.

Fix this by calling acpi_can_fallback_to_crs() in acpi_gpio_count()
before trying to fallback.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The commit 10cf4899 ("gpiolib: tighten up ACPI legacy gpio lookups")
prevents to getting same resource twice if the driver asks twice using
different connection ID.

But the whole idea of fallback might bring some problems. Imagine the case when
we have two versions of BIOS/hardware where in one _DSD is introduced along
with GPIO resources, but the other one uses just plain GPIO resource for
another purpose

Case 1:

    Device (DEVX)
    {
        ...
        Name (_CRS, ResourceTemplate ()
        {
            GpioIo (Exclusive, PullUp, 0, 0, IoRestrictionInputOnly,
                    "\\_SB.GPO0", 0, ResourceConsumer) {15}
        })
        Name (_DSD, Package ()
        {
            ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
            Package ()
            {
                Package () {"some-gpios", Package() {^DEVX, 0, 0, 0 }},
            }
        })
    }

Case 2:

    Device (DEVX)
    {
        ...
        Name (_CRS, ResourceTemplate ()
        {
            GpioIo (Exclusive, PullUp, 0, 0, IoRestrictionInputOnly,
                    "\\_SB.GPO0", 0, ResourceConsumer) {27}
        })
    }

To prevent the possible misconfiguration tighten up even more GPIO ACPI lookups
for case without connection ID provided.

In the past the issue had been triggered by "use mctrl_gpio helpers" series
[1,2].

[1] commit 4ef03d32 ("tty/serial/8250: use mctrl_gpio helpers")
[2] https://patchwork.kernel.org/patch/9283745/

Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Bastien Nocera <hadess@hadess.net>
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Check that we don't ask for output direction on GpioInt resource
in cases with or without _DSD defined.
Reviewed-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

By some reason acpi_find_gpio() and acpi_gpio_count() have compared
connection ID to "gpios" when tries to check if suffix is needed or not.

Don't do any assumptions about what connection ID can be and, when defined,
use it only with suffix as it's done in the device tree version.
Reviewed-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This is preparatory patch for enabling GPIO ACPI to configure a pin
accordingly.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add documentation of new GPIO specifiers indicating if the state of an
output pin should be maintained during sleep/low-power mode.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The Arizona devices only maintain the state of output GPIOs whilst the
CODEC is active, this can cause issues if the CODEC suspends whilst
something is relying on the state of one of its GPIOs. However, in
many systems the CODEC GPIOs are used for audio related features
and thus the state of the GPIOs is unimportant whilst the CODEC is
suspended. Often keeping the CODEC resumed in such a system would
incur a power impact that is unacceptable.

Allow the user to select whether a GPIO output should keep the
CODEC resumed, by adding a flag through the second cell of the GPIO
specifier in device tree.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add new flags to allow users to specify that they are not concerned with
the status of GPIOs whilst in a sleep/low power state.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Commit 4c0facdd ("gpio: core: Decouple open drain/source flag with
active low/high") decoupled the open collector outputs from active
low/high but did not update the documentation.

Update the device tree documentation to correctly reflect this new
separation between the two concepts.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Since the commit "gpio: mvebu: switch to regmap for register access" the
driver use the regmap. Explicitly select the REGMAP_MMIO symbol to fix
build error.
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Broadcom Vulcan (ARCH_VULCAN) has been discontinued and will be deleted
soon. So, update the GPIO_XLP Kconfig entry to remove the ARCH_VULCAN
dependency.

Also update the documentation to note that Cavium ThunderX2 uses this
driver.
Signed-off-by: NJayachandran C <jnair@caviumnetworks.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The mvebu gpio driver can also be used on arm64 mvebu SoC such as the
Armada 7K/8K. This commit allows to build the driver for them (when only
ARCH_MVEBU is defined)
Reviewed-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

In order to be able to use this driver with the Armada 7K/8K SoCs, we
need to use the regmap to access the registers. Indeed for these new SoCs,
the gpio node will be part of a syscon.

[gregory.clement@free-electrons.com:
 - fixed merge conflcit from 4.10 to 4.12-rc1
 - added a commit log]
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This commit sorts alphabetically the header files.
Reviewed-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The comment does not match the driver, which actually supports
automatic assignment. Fix this by updating the comment.
Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The driver supports using mcp23xxx as interrupt controller, so
let's drop all comments stating otherwise.
Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This moves irq property handling from spi/i2c specific code into
the generic mcp23s08_probe_one. This is possible because the
device properties are named equally.

As a side-effect this drops support for setting the properties via
pdata, which has no mainline users. If boardcode wants to enable
the chip as interrupt controller it can attach the device properties
instead.
Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Simplify spi pdata handling, so that it uses pdata when available
and falls back to reading device properties otherwise.
Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Simplify i2c pdata handling, so that it uses pdata when available
and falls back to reading device properties otherwise.
Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Switching to devm_gpiochip_add_data simplifies the driver's
cleanup routine and safes a few loc.
Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Let's remove a few lines of code by using managed memory for mcp
variable.
Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

i2c-core and spi-core already assign the irq, so we
can drop the additional call from the mcp driver.
Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The driver compiles & works perfectly fine without OF_GPIO on x86,
so lets drop the dependency.
Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Instead of using custom caching, this switches to regmap based
caching. Before the conversion the debugfs file used uncached
values, so that it was easily possible to see power-loss related
problems. The new code will check and recover at this place.

The patch will also ensure, that irqs are not cleared by checking
register status in debugfs.
Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

mcp23s08 support configuration of the pullups using the
pinconf framework. This removes the custom pullup configuration
from platform data, which has no upstream users.
Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

mcp23xxx device have configurable 100k pullup resistors. This adds
support for enabling them using pinctrl's pinconf interface.
Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Tested-by: NEnric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This moves the mcp23s08 driver from gpio to pinctrl. Actual
pinctrl support for configuration of the pull-up resistors
follows in its own patch.
Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: NSylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>