pdev is used later on by dev_printk() so must be set.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Callers may stop the SSP core requesting the interrupt so it can't be
freed unconditionally.  Also use NO_IRQ like we should.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The initial patch from Lothar, and Lennert make it into a cleaner
one, modified and tested on PXA320 by Eric Miao.

This patch moves the L2 cache operations out of proc-xsc3.S into
dedicated outer cache support code.

CACHE_XSC3L2 can be deselected so no L2 cache specific code will be
linked in, and that L2 enable bit will not be set, this applies to
the following cases:

    a. _only_ PXA300/PXA310 support included and no L2 cache wanted
    b. PXA320 support included, but want L2 be disabled

So the enabling of L2 depends on two things:

    - CACHE_XSC3L2 is selected
    - and L2 cache is present

Where the latter is only a safeguard (previous testing shows it works
OK even when this bit is turned on).

IXP series of processors with XScale3 cannot disable L2 cache for the
moment since they depend on the L2 cache for its coherent memory, so
IXP may always select CACHE_XSC3L2.

Other L2 relevant bits are always turned on (i.e. the original code
enclosed by #if L2_CACHE_ENABLED .. #endif), as they showed no side
effects. Specifically, these bits are:

   - OC bits in TTBASE register (table walk outer cache attributes)
   - LLR Outer Cache Attributes (OC) in Auxiliary Control Register
Signed-off-by: NLothar WaÃ&lt;9f&gt;mann <LW@KARO-electronics.de>
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

     And also reserve 32 IRQs for the two GPIO expanders.
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NEric Miao <eric.miao@marvell.com>
Cc: Sergey Podstavin <spodstavin@ru.mvista.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NEric Miao <eric.miao@marvell.com>
Cc: Sergey Podstavin <spodstavin@ru.mvista.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

A pxa3xx_set_nand_info() is also introduced to set the PXA3xx NAND
driver specific platform_data structure pointer.
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Cc: Sergey Podstavin <spodstavin@ru.mvista.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

So processor specific clock sources can be defined in pxa300.c
and pxa320.c.
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Some boards want to change low power state of pins on-the-fly, this
function helps to facilitate that operation instead of switching
back-n-forth between two configurations with pxa2xx_mfp_config().
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Tested-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NEric Miao <eric.miao@marvell.com>
Tested-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

pxa320_init_mfp() is simple enough to be embedded into pxa320_init()
to simplify the code a bit.
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Some boards use UART other than FFUART for the console, E.g. Marvell
PXA3xx Form Factor Platform (aka Littleton) uses STUART. This patch
modifies the uncompress.h so that display of the uncompress message
is routed to the STUART.
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Setting PKWR bits on those pins will make the resuming from
low power state to fail.
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The correct macro name when a driver is built as a module is
CONFIG_*_MODULE instead of CONFIG_*_MODULES. This patch fixes
this in several places.
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

	unnecessary menu level
Signed-off-by: NDmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NDmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add a function to dynamically allocate and register pxa2xx-spi platform
devices, to be used by PXA2xx and PXA3xx based systems. Switch pcm027 and
lubbock to use it.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Acked-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The Zylonite has an AC97 subsystem on it so register the AC97 controller
device.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

As well as moving all the device declarations to a single one in devices.c
this causes all platforms to register the I/O and interrupt resources for
the AC97 controller.

Cc: eric miao <eric.miao@marvell.com>
Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Jürgen Schindele <linux@schindele.name>
Cc: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The pxa2xx_udc.c driver is renamed to pxa25x_udc.c (the platform
driver name changes from pxa2xx-udc to pxa25x-udc) and the
platform driver name of pxa27x_udc.c is fixed to pxa27x-udc.
pxa_device_udc in devices.c is split into pxa25x and pxa27x flavors
and the pxa27x_device_udc is enabled in pxa27x.c.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Acked-by: NNicolas Pitre <nico@cam.org>
Acked-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Including from Ian Molton:

Fixes for mistakes left over from the PXA2{5,7}X UDC split.
Signed-off-by: NIan Molton <spyro@f2s.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

	is handled in board code
Signed-off-by: NDmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Provide a set of functions to control state of pins dedicated to IrDA.
Signed-off-by: NDmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NDmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

pxa_set_cken() is now unused, remove it.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

We need to support more than one name+device for a struct clk for a
small number of peripherals.  We do this by re-using struct clk alias
to another struct clk - IOW, if we find that the entry we're using is
an alias, we return the aliased entry not the one we found.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Warn people when using pxa2xx-gpio.h as it is only here for backwards
compatibility. The new mfp-pxa2[57]x.h and the relevant API should be used
instead.
Signed-off-by: NStefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Both i2c-pxa.c and irq.c still include pxa2xx-gpio.h although is is not
needed anymore.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Acked-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds exit and remove handlers to pxafb so that it can be loaded
and unloaded as a module.
Signed-off-by: NJaya Kumar <jayakumar.lkml@gmail.com>
Acked-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NEric Miao <eric.miao@marvell.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

PCM990 boards can be assembled with either a Sharp STN or a NEC TFT LCD. This
patch adds support for these displays and for the backlight, using the pwm_bl
driver.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

magician has a GPIO that modifies the brightness level additionally to
the PWM duty value. This patch makes use of the pwm_bl notify callback
to present userspace with a single brightness scale.
This gets rid of the pxa_set_cken calls and direct PWM register access.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Make the return of pwm_request() be more informative than just
being NULL on error by using PTR_ERR() to respond with an
approriate error.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This allows platform code to manipulate GPIOs and brightness level as
needed.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Acked-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>