The general interrupt handler returns IRQ_HANDLED whether an IRQ
was handled or not.
Determine if an IRQ was handled and return the correct value.
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: NMichael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: NKamenee Arumugam <kamenee.arumugam@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

QSFP reset enables AOC transmitters by default. They should be off
before moving to high power mode to complete the setup. There is no
need to reset the QSFP during LNI failure as it was reset at link down.
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: NJakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: NSebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Offline.quietDuration was added in the 8051 firmware, and the driver
only turns off the AOC transmitters when offline.quiet is reached.
However, the AOC transmitters need to be turned off at the new state.
Therefore, turn off the AOC transmitters at any offline substates
including offline.quiet and offline.quietDuration, then recheck we
reached offline.quiet to support backwards compatibility.
Reviewed-by: NJakub Byczkowski <jakub.byczkowski@intel.com>
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NSebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Ratelimit error prints from sdma_interrupt function
that could swarm dmesg otherwise.
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NGrzegorz Morys <grzegorz.morys@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Do not track physical state separately from host_link_state.
Deduce physical state from host_link_state when required.
Change cache_physical_state to log_physical_state to make
sure host_link_state reflects hardwares physical state properly.
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NJakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Check xchg returned value for queuing link down entry
to guarantee proper atomic value reads.

Fixes: 626c077c ("IB/hfi1: Prevent link down request double queuing")
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NSebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Increase lid used in hfi1 driver to 32 bits. qib continues
to use 16 bit lids.
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: NDon Hiatt <don.hiatt@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

We introduce a struct hfi1_16b_header to support 16B headers.
16B bypass packets are received by the driver and processed
similar to 9B packets. Add basic support to handle 16B packets.
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDon Hiatt <don.hiatt@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

There is a mixture of mutex and spinlocks to protect receive context
(rcd/uctxt) information.  This is not used consistently.

Use the mutex to protect device receive context information only.
Use the spinlock to protect sub context information only.

Protect access to items in the rcd array with a spinlock and
reference count.

Remove spinlock around dd->rcd array cleanup.  Since interrupts are
disabled and cleaned up before this point, this lock is not useful.
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: NSebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: NMichael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The rcd array can be accessed from user context or during interrupts.
Protecting this with a mutex isn't a good idea because the mutex should
not be used from an IRQ.

Protect the allocation and freeing of rcd array elements with a
spinlock.
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: NSebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: NMichael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Do not track logical state separately from host_link_state. Deduce
logical state from host_link_state when required. Transitions in
set_link_state and goto_offline already make sure host_link_state
reflects hardware's logical state properly.
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NJakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Trivial fix to spelling mistake, rename variable 'continious'
to the correct spelling 'continuous'
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Acked-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Always initiate an offline transition request
when a link down occurs. The firmware will
use this request to confirm that the driver
has seen the link down message. A host version
is set to indicate this driver behavior to the
firmware.
Reviewed-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NSebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

When link interrupts occur, multiple link down requests
could be queued up when only one is needed. This could get
the hfi1 out of sync with its link partner during LNI.

Only allow one link down request to be queued at any one time.
Reviewed-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NSebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Currently, link down interrupts queue link entries
on a workqueue intended for sending events only.
Create a workqueue for queuing link events.
Reviewed-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NSebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Fix issue where a disabled port can be enabled by
inserting a cable. The port should be explicitly
enabled instead.
Reviewed-by: NMichael J. Ruhl <michael.j.ruhl@intel.com>
Reviewed-by: NJakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: NJan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

There is a window that allows other threads to read state of
'host_link_state' as a new, before the hardware actual state is set.
This patch closes the window by indicating a new state only after
hardware transition is complete.
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NAlex Estrin <alex.estrin@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

There is a window where the FM can read the buffer control table
and decide not to program buffers. When a port goes down, the code
clears the table and if it is not programmed, posted SDMA descriptors
will never complete due to no buffer credits.
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NAlex Estrin <alex.estrin@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

During PCIe initialization some registers' values from
PCI config space are saved in order to restore them later
(i.e. after reset). Restoring those value is done by a
function called restore_pci_variables, while saving them
is put directly into function hfi1_pcie_ddinit.
Move saving values to a separate function in the image
of restoring functionality.
Reviewed-by: NJakub Byczkowski <jakub.byczkowski@intel.com>
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NBartlomiej Dudek <bartlomiej.dudek@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Code structure is not consistent for if/else blocks and break
instructions in set_link_state for case HLS_UP_INIT. Physical
state uses break in case of an error and if/else blocks for
logical use cases. These blocks should be implemented consistently.
Reviewed-by: NJakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: NJan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The hfi1_rcvctrl() function receives an index which it then converts
to an rcd.  Since most functions have the rcd, use that instead.
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: NSebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: NMichael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The hfi1_<set|clear>_ctxt_<j|p>key functions take a context index and
look up the context based on that index.

Since the context index is being retrieved from the context, this
doesn't seem optimal.

Pass the context pointer for use, rather than the context index.
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NMichael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The array index for the rcd array is sized several different ways
throughout the code.

Use the user interface size (u16) as the standard size and update the
necessary code to reflect this.

u16 is large enough for the largest amount of supported contexts.
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NMichael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

When the debugpat kernel boot flag is turned on the following
traces are printed:

[ 1884.793168] x86/PAT: Overlap at 0x90000000-0x92000000
[ 1884.803510] x86/PAT: reserve_memtype added [mem 0x91200000-0x9127ffff],
track uncached-minus, req write-combining, ret uncached-minus
[ 1884.818167] hfi1 0000:05:00.0: hfi1_0: WC Remapped RcvArray:
ffffc9000a980000

The ioremap_wc() clearly is not returning a write combining mapping due
to an overlap where the RcvArray is mapped in a uncached mapping prior
to creating the proposed write combining mapping.

The patch replaces the single base register for uncached CSRs that
used to overlap the RcvArray with two mappings.   One, kregbase1, from the
bar0 up to the RcvArray and another, kregbase2, from the end of the
RcvArray to the pio send buffer space.  A new dd field, base2_start,
is used to convert the zero-based offset in the CSR routines to the
correct kregbase1/kregbase2 mapping.  A single direct write of the
RcvArray CSRs is replaced with hfi1_put_tid() to insure correct access
using the new disjoint mapping.

Additionally, the kregend field is deleted since it is only ever written.

patdebug now shows the RcvArray as write combining:
[   35.688990] x86/PAT: reserve_memtype added [mem 0x91200000-0x9127ffff],
track write-combining, req write-combining, ret write-combining

To insulate from any potential issues with write combining, all
writeq are now flushed in hfi1_put_tid() and rcv_array_wc_fill().
Reviewed-by: NMitko Haralanov <mitko.haralanov@intel.com>
Reviewed-by: NAshutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Ensure that return values from kernel PCI config access
API calls in HFI driver are checked and react properly if
they are not expected (i.e. not successful).
Reviewed-by: NJakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: NBartlomiej Dudek <bartlomiej.dudek@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

As the code stands today the array access in remap_intr() is OK. To
future proof the code though we should explicitly check to ensure the
index value is not outside of the valid range. This is not a straight
forward calculation so err on the side of caution.
Reviewed-by: NMichael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

This patch adds a trace for putting a TID and
for writing the RcvArray CSR.

The CSR access template can be easily extended for additional
CSR readq/writeq calls.
Reviewed-by: NAshutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Change QSFP cable error events logging levels from info to error.
Reviewed-by: NJakub Byczkowski <jakub.byczkowski@intel.com>
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NJan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Fix info array of host message flags by adding entry
for link width downgrade and reverse values for
BC SMA and BC PWR_MSG messages
Reviewed-by: NJakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: NBartlomiej Dudek <bartlomiej.dudek@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Ensure states returned to the Fabric Manager are consistent with
the OPA specification by caching the physical state along with the
logical state.
Reviewed-by: NStuart Summers <john.s.summers@intel.com>
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Reviewed-by: NAndrzej Kotlowski <andrzej.kotlowski@intel.com>
Signed-off-by: NJakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Spell receive correctly in OPA_LINKDOWN_REASON_RCV_ERROR
Reviewed-by: NMichael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

As the code stands today the array access in remap_intr() is OK. To
future proof the code though we should explicitly check to ensure the
index value is not outside of the valid range. This is not a straight
forward calculation so err on the side of caution.
Reviewed-by: NMichael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

pci_enable_msix_range() and pci_disable_msix() have been deprecated.
Updating to the new pci_alloc_irq_vectors() interface.
Reviewed-by: NSebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: NMichael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

We move many common IB fields into the hfi1_packet structure and
set them up in a single function. This allows us to set the fields
in a single place and not deal with them throughout the driver.
Reviewed-by: NBrian Welty <brian.welty@intel.com>
Reviewed-by: NDasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDon Hiatt <don.hiatt@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Keep VL15 credits at 0 during LNI, before link-up. Store
VL15 credits value during verify cap interrupt and set
in after link-up. This addresses an issue where VL15 MAD
packets could be sent by one side of the link before
the other side is ready to receive them.
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: NDean Luick <dean.luick@intel.com>
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NJakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Context initialization mixes base context init with sub context init.
This is bad because contexts can be reused, and on reuse, reinit things
that should not re-initialized.

Normalize comments and function names to refer to base context and
sub context (not main, shared or slaves).

Separate the base context initialization from sub context initialization.

hfi1_init_ctxt() cannot return an error so changed to a void and remove
error message.
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NMichael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

In the close path the context is removed from the device array, and then
the clear pkey function is called.  The pkey function trys to get the
context from the device array, but because it was removed the clearing
does not occur.

Rework pkey clear function to work as expected.  Update the function
variable to reflect the correct size and name of the hw_context.
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NMichael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

To improve the readability of function prototypes, give the parameters
names.
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NMichael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

In goto_offline() function pstate is masked by 0xff when compared
to PLS_OFFLINE state. Mask should be 0xf0, since upper 4 bits
specify the "major" state.
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: NEaswar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: NJakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Add missing braces around else blocks in a few places to make checkpatch
happy.

Fixes: 77241056 ("IB/hfi1: add driver files")
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>