Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 17 3月, 2008 1 次提交
  3. 20 7月, 2007 1 次提交
  5. 12 2月, 2007 1 次提交
  7. 17 10月, 2006 2 次提交
  9. 07 10月, 2006 1 次提交
    • J
      Various drivers' irq handlers: kill dead code, needless casts · c7bec5ab
      由 Jeff Garzik 提交于 
      - Eliminate casts to/from void*

- Eliminate checks for conditions that never occur.  These typically
  fall into two classes:

	1) Checking for 'dev_id == NULL', then it is never called with
	NULL as an argument.

	2) Checking for invalid irq number, when the only caller (the
	system) guarantees the irq handler is called with the proper
	'irq' number argument.
Signed-off-by: NJeff Garzik <jeff@garzik.org>
      c7bec5ab
  11. 05 10月, 2006 1 次提交
    • D
      IRQ: Maintain regs pointer globally rather than passing to IRQ handlers · 7d12e780
      由 David Howells 提交于 
      Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.

The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around.  On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).

Where appropriate, an arch may override the generic storage facility and do
something different with the variable.  On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.

Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions.  Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller.  A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.

I've build this code with allyesconfig for x86_64 and i386.  I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.

This will affect all archs.  Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:

	struct pt_regs *old_regs = set_irq_regs(regs);

And put the old one back at the end:

	set_irq_regs(old_regs);

Don't pass regs through to generic_handle_irq() or __do_IRQ().

In timer_interrupt(), this sort of change will be necessary:

	-	update_process_times(user_mode(regs));
	-	profile_tick(CPU_PROFILING, regs);
	+	update_process_times(user_mode(get_irq_regs()));
	+	profile_tick(CPU_PROFILING);

I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().

Some notes on the interrupt handling in the drivers:

 (*) input_dev() is now gone entirely.  The regs pointer is no longer stored in
     the input_dev struct.

 (*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking.  It does
     something different depending on whether it's been supplied with a regs
     pointer or not.

 (*) Various IRQ handler function pointers have been moved to type
     irq_handler_t.
Signed-Off-By: NDavid Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
      7d12e780
  13. 03 7月, 2006 1 次提交
  15. 01 7月, 2006 1 次提交
  17. 30 6月, 2006 1 次提交
  19. 28 6月, 2006 1 次提交
  21. 23 6月, 2006 1 次提交
  23. 04 5月, 2006 1 次提交
  25. 02 5月, 2006 1 次提交
  27. 11 4月, 2006 1 次提交
  29. 01 3月, 2006 1 次提交
  31. 28 2月, 2006 1 次提交
    • J
      [IA64] show "SN Devices" menu only if CONFIG_SGI_SN · 50e300de
      由 Jes Sorensen 提交于 
      Adrian> On architectures like i386, the "Multimedia Capabilities Port
Adrian> drivers" menu is visible, but it can't be visited since it
Adrian> contains nothing usable for CONFIG_SGI_SN=n.

Jes> Thats only a third of the patch, if you want to do that, you should
Jes> remove the redundant SGI_SN checks below.
Signed-off-by: NTony Luck <tony.luck@intel.com>
      50e300de
  33. 08 2月, 2006 1 次提交
  35. 02 2月, 2006 1 次提交
  37. 27 1月, 2006 1 次提交
  39. 15 1月, 2006 1 次提交
    • P
      [PATCH] Altix: ioc3 serial support · 2d0cfb52
      由 Patrick Gefre 提交于 
      Add driver support for a 2 port PCI IOC3-based serial card on Altix boxes:

This is a re-submission.  On the original submission I was asked to
organize the code so that the MIPS ioc3 ethernet and serial parts could be
used with this driver.  Stanislaw Skowronek was kind enough to provide the
shim layer for this - thanks Stanislaw.  This patch includes the shim layer
and the Altix PCI ioc3 serial driver.  The MIPS merged ioc3 ethernet and
serial support is forthcoming.
Signed-off-by: NPatrick Gefre <pfg@sgi.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
      2d0cfb52
  41. 22 6月, 2005 3 次提交
    • B
      [PATCH] ioc4: PCI bus speed detection · d4c477ca
      由 Brent Casavant 提交于 
      Several hardware features of SGI's IOC4 I/O controller chip require
timing-related driver calculations dependent upon the PCI bus speed.  This
patch enables the core IOC4 driver code to detect the actual bus speed and
store a value that can later be used by the IOC4 subdrivers as needed.
Signed-off-by: NBrent Casavant <bcasavan@sgi.com>
Acked-by: NPat Gefre <pfg@sgi.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
      d4c477ca
    • B
      [PATCH] ioc4: CONFIG split · e5d310b3
      由 Brent Casavant 提交于 
      The SGI IOC4 I/O controller chip drivers are currently all configured by
CONFIG_BLK_DEV_SGIIOC4.  This is undesirable as not all IOC4 hardware features
are needed by all systems.

This patch adds two configuration variables, CONFIG_SGI_IOC4 for core IOC4
driver support (see patch 1/3 in this series for further explanation) and
CONFIG_SERIAL_SGI_IOC4 to independently enable serial port support.
Signed-off-by: NBrent Casavant <bcasavan@sgi.com>
Acked-by: NPat Gefre <pfg@sgi.com>
Acked-by: NJeremy Higdon <jeremy@sgi.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
      e5d310b3
    • B
      [PATCH] ioc4: Core driver rewrite · 22329b51
      由 Brent Casavant 提交于 
      This series of patches reworks the configuration and internal structure
of the SGI IOC4 I/O controller device drivers.

These changes are motivated by several factors:

- The IOC4 chip PCI resources are of mixed use between functions (i.e.
  multiple functions are handled in the same address range, sometimes
  within the same register), muddling resource ownership and initialization
  issues.  Centralizing this ownership in a core driver is desirable.

- The IOC4 chip implements multiple functions (serial, IDE, others not
  yet implemented in the mainline kernel) but is not a multifunction
  PCI device.  In order to properly handle device addition and removal
  as well as module insertion and deletion, an intermediary IOC4-specific
  driver layer is needed to handle these operations cleanly.

- All IOC4 drivers are currently enabled by a single CONFIG value.  As
  not all systems need all IOC4 functions, it is desireable to enable
  these drivers independently.

- The current IOC4 core driver will trigger loading of all function-level
  drivers, as it makes direct calls to them.  This situation should be
  reversed (i.e. function-level drivers cause loading of core driver)
  in order to maintain a clear and least-surprise driver loading model.

- IOC4 hardware design necessitates some driver-level dependency on
  the PCI bus clock speed.  Current code assumes a 66MHz bus, but the
  speed should be autodetected and appropriate compensation taken.

This patch series effects the above changes by a newly and better designed
IOC4 core driver with which the function-level drivers can register and
deregister themselves upon module insertion/removal.  By tracking these
modules, device addition/removal is also handled properly.  PCI resource
management and ownership issues are centralized in this core driver, and
IOC4-wide configuration actions such as bus speed detection are also
handled in this core driver.

This patch:

The SGI IOC4 I/O controller chip implements multiple functions, though it is
not a multi-function PCI device.  Additionally, various PCI resources of the
IOC4 are shared by multiple hardware functions, and thus resource ownership by
driver is not clearly delineated.  Due to the current driver design, all core
and subordinate drivers must be loaded, or none, which is undesirable if not
all IOC4 hardware features are being used.

This patch reorganizes the IOC4 drivers so that the core driver provides a
subdriver registration service.  Through appropriate callbacks the subdrivers
can now handle device addition and removal, as well as module insertion and
deletion (though the IOC4 IDE driver requires further work before module
deletion will work).  The core driver now takes care of allocating PCI
resources and data which must be shared between subdrivers, to clearly
delineate module ownership of these items.
Signed-off-by: NBrent Casavant <bcasavan@sgi.com>
Acked-by: Pat Gefre <pfg@sgi.com
Acked-by: NJeremy Higdon <jeremy@sgi.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
      22329b51
  43. 17 4月, 2005 1 次提交
    • L
      Linux-2.6.12-rc2 · 1da177e4
      由 Linus Torvalds 提交于 
      Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!
      1da177e4