Commit [3469adb3: fix potential NULL pointer dereference] introduced
a check of msg_ind allocation, but omitted allocation of msg_ind->msg.
Moreover, it introduced two if statements, which looked a bit clunky.

This commit moves allocation code outside of the critical section so
there's no need to dance around mutex_unlock, and adds the missing
allocation check.
Signed-off-by: NMichal Nazarewicz <mina86@mina86.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Reviewed-by: NEyalX Shapira <eyal@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

RTS protection was turned on once aggregation was enabled but it
was never turned off. Remove turning on RTS protection in the LQ command
completely as TX_CMD_FLG_PROT_REQUIRE gets set in iwl_mvm_set_tx_cmd
for every Tx which is part of an aggregation. This would already cause
RTS protection to be used during aggregations.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Set the Tx/Rx highest long GI rates in the VHT Supported MCS Set
field according to the chip capabilties.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

MCS9 introduces some corner cases in the current rs
algorithm which may lead to non optimal throughput and
instability in the throughput. Until all the corner
cases are resolved disable MCS9 for Tx as a workaround
which yields better throughput results as MCS8 is much
more stable.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Fix a regression introduced in "iwlwifi: mvm: fix ht protection flags"
where an AP/IBSS MAC context could have been updated even before the
context was added to the FW. This fix avoids the following warning:

WARNING: ... at .../drivers/net/wireless/iwlwifi/mvm/mac-ctxt.c:1132
    iwl_mvm_mac_ctxt_changed+0x75/0x90 [iwlmvm]()
Changing inactive MAC 0c:8b:fd:01:1a:30/3
Modules linked in: [...]
Call Trace:
[<c16041fd>] dump_stack+0x41/0x52
[<c1041074>] warn_slowpath_common+0x84/0xa0
[<f80d8f45>] ? iwl_mvm_mac_ctxt_changed+0x75/0x90 [iwlmvm]
[<f80d8f45>] ? iwl_mvm_mac_ctxt_changed+0x75/0x90 [iwlmvm]
[<c1041133>] warn_slowpath_fmt+0x33/0x40
[<f80d8f45>] iwl_mvm_mac_ctxt_changed+0x75/0x90 [iwlmvm]
[<f80d517a>] iwl_mvm_bss_info_changed+0x22a/0x4b0 [iwlmvm]
[<c160831d>] ? mutex_unlock+0xd/0x10
[<f80d4678>] ? iwl_mvm_configure_filter+0x58/0x70 [iwlmvm]
[<f80d4f50>] ? iwl_mvm_mac_tx+0xc0/0xc0 [iwlmvm]
[<f8132d83>] ieee80211_bss_info_change_notify+0xa3/0x1d0 [mac80211]
[<f8149247>] ? ieee80211_del_virtual_monitor+0x127/0x1f0 [mac80211]
[<f8149cac>] ieee80211_do_open+0x12c/0xeb0 [mac80211]
[<c106c6de>] ? __raw_notifier_call_chain+0x1e/0x30
[<c106c70f>] ? raw_notifier_call_chain+0x1f/0x30
[<f814aa8d>] ieee80211_open+0x5d/0x60 [mac80211]
[<c1500c7b>] __dev_open+0xab/0x140
[<c160b39a>] ? _raw_spin_unlock_bh+0x2a/0x30
[<c1500f41>] __dev_change_flags+0x81/0x160
[<c10ab6fc>] ? __lock_is_held+0x3c/0x60
[<c15010d1>] dev_change_flags+0x21/0x60
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Reported-by: NJohannes Berg <johannes.berg@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

debufs.o appeared twice in the Makefile. Fix that.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Extract the scale action decision to a different function
in preparation of modifying it. While at it also convert
the scale action values from hardcoded values to a clear enum.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The logs are emitted in a flow in which there were retries
and the rates in the rate table entry didn't match the active
or search table. This doesn't indicate a problem and is
expected in most cases where there will be retries for some
reason. Remove the logs.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The new logic will attempt more rates with less retries
per rate. Also when starting off with MIMO it will
fallback to SISO with the same MCS and only then to Legacy.
Previously we fell back directly to Legacy.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The supported legacy rate mask is initialized when rs
is initialized based on the remote peer supported rates.
There's no need to re mask it repeatedly with the supported
remote peer rates.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Simplify the code a bit more by extracting the rates table
building logic into a separate function and handle setting
a fixed rate for debug in a separate flow.
Also avoid using and saving ucode rate format in different
places. Instead use rs_rate struct and convert to ucode format
only when filling the rates table in the LQ command.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Current firmware doesn't handle well uAPSD in P2P Client.
When it will be fixed, the firmware will set a TLV flag to notify
the driver that uAPSD is supported in P2P client mode.
Check this flag when sending power command for P2P client.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

It is not currently implemented for SDIO, and not required for other slave
buses as well.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Clear the FW_ERROR status before the common start_fw transport code.
Remove the transport specific clears.

After these patches the FW_ERROR flag is only set and cleared by common
transport code.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In case a sync command timeouts or Tx is stuck while a FW error
interrupt arrives, we might call iwl_op_mode_nic_error twice before
a restart has been initiated. This will cause a reprobe. Unify calls
to this function at the transport level and only call it on the first
FW error in a given by checking the transport FW error flag.

While at it, remove the privately defined iwl_nic_error from PCIE code
and use the common callback instead.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

iwl_nvm_init() return value wasn't checked in some
path, which resulted in the following panic (if
there was some issue with the nvm):

Unable to handle kernel NULL pointer dereference at virtual address 00000004
pgd = d0460000
[00000004] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP
Modules linked in: iwlmvm(+) iwlwifi mac80211 cfg80211 compat [last unloaded: compat]
PC is at iwl_mvm_mac_setup_register+0x12c/0x460 [iwlmvm]
LR is at 0x2710
pc : [<bf50dd4c>]    lr : [<00002710>]    psr: 20800013
sp : d00cfe18  ip : 0000081e  fp : d006b908
r10: d0711408  r9 : bf532e64  r8 : d006b5bc
r7 : d01af000  r6 : bf39cefc  r5 : d006ab00  r4 : d006b5a4
r3 : 00000001  r2 : 00000000  r1 : d006a120  r0 : d006b860
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This pointer was not used anywhere.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Move rs_program_fix_rate right before it's caller where we're
already in the context of an ifdef CPTCFG_MAC80211_DEBUGFS so
we can get rid of the extra ifdefs surrounding the original
location.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Stop Tx and commands from arriving to the transport layer when a FW
error has occurred. A HW recovery should take place before. Remove
transport specific checks of the same nature (note that not all
transports were protected).
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The same bits are employed in all transport layers. Put the status
field in the common transport layer. This allows us to employ them
in common transport code.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The stop_hw trans callback is not well defined. It is missing in many
cleanup flows and the division of labor between stop_device/stop_hw
is cumbersome. Remove stop_hw and use stop_device to perform both.
Implement this for all current transports.

PCIE needs some extra configuration the op-mode is leaving to configure
RF kill. Expose this explicitly as a new op_mode_leave trans callback.
Take the call to stop_device outside iwl_run_mvm_init_ucode, this
makes more sense and WARN when we want to run the INIT firmware while
it has run already.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The documentation for smps_requests is unclear, rewrite it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Configure the phy context to the minimum required
bandwidth, given by ctx->min_def.

Tuning to a narrower bandwidth should reduce the
noise level and consume less power.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Configure the fw to filter multicast according to
the addresses given by mac80211.

Note that bssid should be given even if we want
to pass all the multicast frames.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This is more related to phy contexts than to mac context.
Move this function to there.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This allows to tweak the power parameters per vif.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Enable power save on P2P client interface only if it is the
only bound interface.
Avoid using uAPSD if P2P client is associated to GO that uses
opportunistic power save. This is due to current FW limitation.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When monitor interface is activated device power save needs
to be disabled.
Re-consider power management status on other active
interfaces when monitor interface is bound or unbound.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

FW still does not support power management on multiple MAC interfaces.
Currently the driver enforce this limitation by disabling PM if second
interface is added. Change this behavior to allow PM on a single interface
even if other interfaces exist but not bound to any specific PHY.
PM will be enabled if only one single interface is bound.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

FW implements protective algorithm to identify AP's improper uAPSD
behavior. FW sends misbehaving AP notification in this case.
Add this notification handling. Avoid using uAPSD in next association
to the exactly same AP. Refactor iwl_mvm_power_build_cmd() to move
uAPSD related code to a separate function.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

If the device is MIMO and VHT capable it supports Tx STBC.
Unlike HT, any chip that supports VHT also support STBC so
no need for a config parameter.
Using num_of_ants multiple times warranted caching it.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

It was set to zero which reflects support of a single STS.
Set according to the number of Rx antennas which correctly
reflects the number of STSs the STA can receive in a VHT NDP.
This improves beamforming and has been tested to improve Rx
throughput.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Not all chips support STBC so allow this to be
another config parameter per chip type. If STBC
is supported then publish it in the HT caps.

Since 7260/7265/3160 chips support it - set the stbc
support bit.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This patch adds a cipher scheme support to extend a set of
the supported ciphers. The driver reads a cipher scheme list TLV
from FW image and passes it to mac80211 on hw registration.
After the cipher schemes are registered the driver handles key
installation and Tx/Rx calls related to the new ciphers.
Signed-off-by: NMax Stepanov <Max.Stepanov@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Send firmware a Smart FIFO Configuration host command to allow
interrupt coalescing. The smart FIFO is enabled when there is
only one bound interface (other than  p2p devices which are
ignored) and it is of type station, and activated while the
station is associated.

Smart Fifo allows aggragations of DMA transactions and by that
causes processor and memory controller to stay for a longer time
on lower c-states, thus saving platform power.
Firmware relies on driver to activate and disable it.
Signed-off-by: NLilach Edelstein <lilach.edelstein@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add VHT MCS/NSS set support for nl80211_set_tx_bitrate_mask().
This should be used mainly for test purpose, to check
different MCS/NSS VHT combinations.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Allow to read management keys stored in a station's gtk key
array with a get_key function.
Signed-off-by: NMax Stepanov <Max.Stepanov@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Verify that a pairwise key index value on ieee80211_get_key call
doesn't exceed the boundaries of the pairwise key array.
Signed-off-by: NMax Stepanov <Max.Stepanov@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>