78f1cd02 ("fix broken register writes")
does not work for Al Viro's r8169 (XID 18000000).
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Few (6) network drivers enable mwi explicitly. Fewer worry about a
failure.

It is not a fix but it should avoid some annoyance like
http://bugzilla.kernel.org/show_bug.cgi?id=15454Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Conrad Kostecki <conikost@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tg3: Fix INTx fallback when MSI fails

MSI setup changes the value of irq_vec in struct tg3 *tp.
This attribute must be taken into account and restored before
we try to do a new request_irq for INTx fallback.

In powerpc, the original code was leading to an EINVAL return within
request_irq, because the driver was trying to use the disabled MSI
virtual irq number instead of tp->pdev->irq.
Signed-off-by: NAndre Detsch <adetsch@br.ibm.com>
Acked-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Nothing stops the workqueue being left to run in parallel with close or a
few other operations. This causes double unmaps and the like.

See kerneloops.org #1041230 for an example
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

gianfar driver may pass NULL pointer to the of_translate_address(),
which may lead to a kernel oops. Fix this by using of_iomap(), which
is also much simpler and shorter.
Signed-off-by: NAnton Vorontsov <avorontsov@mvista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Old P1020RDB device trees were not specifing tbipa address for
MDIO nodes, which is now causing this kernel oops:

 ...
 eth2: TX BD ring size for Q[6]: 256
 eth2: TX BD ring size for Q[7]: 256
 Unable to handle kernel paging request for data at address 0x00000000
 Faulting instruction address: 0xc0015504
 Oops: Kernel access of bad area, sig: 11 [#1]
 ...
 NIP [c0015504] memcpy+0x3c/0x9c
 LR [c000a9f8] __of_translate_address+0xfc/0x21c
 Call Trace:
 [df839e00] [c000a94c] __of_translate_address+0x50/0x21c (unreliable)
 [df839e50] [c01a33e8] get_gfar_tbipa+0xb0/0xe0
 ...

The old device trees are buggy, though having a dead ethernet is
better than a dead kernel, so fix the issue by using of_iomap().

Also, a somewhat similar issue exist in the probe() routine, though
there the oops is only a possibility. Nonetheless, fix it too.
Signed-off-by: NAnton Vorontsov <avorontsov@mvista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add new driver to use tethering with an iPhone device. After initial submission,
apply fixes to fit the new driver into the kernel standards.

There are still a couple of minor (almost cosmetic-level) issues, but the driver
is fully functional right now.
Signed-off-by: NL. Alberto Giménez <agimenez@sysvalve.es>
Signed-off-by: NDiego Giagio <diego@giagio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I encountered an issue that not to link up on cxgb3 fabric.
I bisected and found that this regression was introduced by
0f07c4ee.

Correct to pass phy_addr to cphy_init() at t3_xaui_direct_phy_prep().
Signed-off-by: NHiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Acked-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix NULL pointer dereference in ks8851_tx_work by checking if dequeued
list is already empty before writing the packet to TX FIFO

 Unable to handle kernel NULL pointer dereference at virtual address 00000050
 PC is at ks8851_tx_work+0xdc/0x1b0
 LR is at wait_for_common+0x148/0x164
 pc : [<c01c0df4>]    lr : [<c025a980>]    psr: 20000013
 Backtrace:
  ks8851_tx_work+0x0/0x1b0
  worker_thread+0x0/0x190
  kthread+0x0/0x90
Signed-off-by: NAbraham Arce <x0066660@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update the stats counter calculation in 3c574_cs, similar
to the method used in 3c589_cs. This corrects the contents
of the counter on tests using a "Megahertz 574B" card.

[linux@dominikbrodowski.net: clean up commit message]
Signed-off-by: NAlexander Kurz <linux@kbdbabel.org>
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In ems_usb_probe(), a pointer is dereferenced after making sure it is NULL...

This patch replaces netdev->dev.parent with &intf->dev in dev_err() calls to
avoid this.
Signed-off-by: N"Hans J. Koch" <hjk@linutronix.de>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAlexander Kuznetsov <alr.kuznetsov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tx_queue is used as a temporary queue when not allowed to queue skb
directly to the hw device driver (which may sleep). Most paths flush
it before returning, but ppp_start() currently cannot. Make sure we
don't leave skbs pointing to a non-existent device.

Thanks to Michael Barkowski for reporting this problem.
Signed-off-by: NKrzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For 6000 series, the 2.4G HT40 band regulatory settings address in EEPROM
was off by 2.

Before the fix, you'll see this in dmesg:
[79535.788877] ieee80211 phy8: U iwl_mod_ht40_chan_info HT40 Ch. 7 [2.4GHz]
WIDE (0x61 0dBm): Ad-Hoc not supported
[79535.788880] ieee80211 phy8: U iwl_mod_ht40_chan_info HT40 Ch. 11 [2.4GHz]
WIDE (0x61 0dBm): Ad-Hoc not supported

And after the fix:
[91132.688706] ieee80211 phy14: U iwl_mod_ht40_chan_info HT40 Ch. 7 [2.4GHz]
IBSS ACTIVE WIDE (0x6f 0dBm): Ad-Hoc supported
[91132.688709] ieee80211 phy14: U iwl_mod_ht40_chan_info HT40 Ch. 11 [2.4GHz]
IBSS ACTIVE WIDE (0x6f 0dBm): Ad-Hoc supported
Signed-off-by: NShanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

When an internal scan is started, nothing protects the
is_internal_short_scan variable which can cause crashes,
cf. https://bugzilla.kernel.org/show_bug.cgi?id=15667.
Fix this by making the short scan request use the mutex
for locking, which requires making the request go to a
work struct so that it can sleep.
Reported-by: NPeter Zijlstra <peterz@infradead.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

The following situation was observed in the field:
tap1 sends packets, tap2 does not consume them, as a result
tap1 can not be closed. This happens because
tun/tap devices can hang on to skbs undefinitely.

As noted by Herbert, possible solutions include a timeout followed by a
copy/change of ownership of the skb, or always copying/changing
ownership if we're going into a hostile device.

This patch implements the second approach.

Note: one issue still remaining is that since skbs
keep reference to tun socket and tun socket has a
reference to tun device, we won't flush backlog,
instead simply waiting for all skbs to get transmitted.
At least this is not user-triggerable, and
this was not reported in practice, my assumption is
other devices besides tap complete an skb
within finite time after it has been queued.

A possible solution for the second issue
would not to have socket reference the device,
instead, implement dev->destructor for tun, and
wait for all skbs to complete there, but this
needs some thought, probably too risky for 2.6.34.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Tested-by: NYan Vugenfirer <yvugenfi@redhat.com>
Acked-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a fix for bug 572201 @ bugs.debian.org

This patch fixes the TX_LIMIT feature flag. The previous logic check
for TX_LIMIT2 also took into account a device that only had TX_LIMIT
set.
Reported-by: NStephen Mulcahu <stephen.mulcahy@deri.org>
Reported-by: NBen Huchings <ben@decadent.org.uk>
Signed-off-by: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

smc91c92_cs:
  * define multicast_table as unsigned char
  * remove unnecessary "#ifndef final_version"
Signed-off-by: NKen Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tx ring buffers after tx_ring->next_to_use are volatile and could
change, possibly causing a crash.  Stop cleaning when we hit
tx_ring->next_to_use.
Signed-off-by: NTerry Loftin <terry.loftin@hp.com>
Acked-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Restrict Wake-on-LAN to first port on 82576 ET2 quad port NICs, as it is
only supported there.
Signed-off-by: NStefan Assmann <sassmann@redhat.com>
Acked-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add missing sg_init_table for sg_set_buf in virtio_net which
induced in defer skb patch.
Reported-by: NThomas Müller <thomas@mathtm.de>
Tested-by: NThomas Müller <thomas@mathtm.de>
Signed-off-by: NShirley Ma <xma@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current algorithm will sometimes "detect" that
more chains are enabled than are really present in
the device because, for unknown reasons, the ucode
sends up all-zeroes signal values.

The simplest way of solving this is to restrict the
active chains mask to the chains we know are really
present on the device.

This fixes a bug with some devices where, since sometimes
more chains are enabled than really present, the system would hang.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

For 4965, need to check it is valid qos frame before free, only valid
QoS frame has the tid used to free the packets.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix rx_pause management in myri10ge_set_pauseparam().
Signed-off-by: NBrice Goglin <brice@myri.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Resource size should be calculated as end - start + 1 because we start
counting at zero.  I changed the code to resource_size() to do the 
calculation.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

cnic_service_bnx2x() irq handler can be called during chip reset from
MTU change.  Need to check that the cnic's device state is up before
handling the irq.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If interface is down, mac address request are not sent to fw
but it is getting add in driver mac list.
Driver mac list should be in sync with fw i.e addresses communicated
to fw.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As reported in <https://bugzilla.kernel.org/show_bug.cgi?id=15355>, r6040_
multicast_list currently crashes. This is due a wrong maximum of multicast
entries. This patch fixes the following issues with multicast:

- number of maximum entries if off-by-one (4 instead of 3)

- the writing of the hash table index is not necessary and leads to invalid
values being written into the MCR1 register, so the MAC is simply put in a non
coherent state

- when we exceed the maximum number of mutlticast address, writing the
broadcast address should be done in registers MID_1{L,M,H} instead of
MID_O{L,M,H}, otherwise we would loose the adapter's MAC address
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the enable_radio being uninitialized, ath_radio_enable() might be
called twice, which can leave some hardware in an undefined state.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

smc91c92_cs:
 *cvt_ascii_address returns 0, if success.
 *call free_netdev, if we can't find hardware address.
Signed-off-by: NKen Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We used to free all the Tx queues memory when interface is brought
down and reallocate them again in interface up. This requires
order-4 allocation for txq->cmd[]. In situations like s2ram, this
usually leads to allocation failure in the memory subsystem. The
patch fixed this problem by allocating the Tx queues memory only at
the first time. Later iwl_down/iwl_up only initialize but don't
free and reallocate them. The memory is freed at the device removal
time. BTW, we have already done this for the Rx queue.

This fixed bug https://bugzilla.kernel.org/show_bug.cgi?id=15551Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Acked-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

When collecting tx data for non-aggregation packets in rate scaling, if
the tx data matches "other table", it still uses current table to update
the stats and calculate average throughput in function rs_collect_tx_data().
This can mess up the rate scaling data structure and cause a kernel panic
in a BUG_ON statement in rs_rate_scale_perform().

To fix this bug, we pass table pointer instead of window pointer (pointed
to by table pointer) to function rs_collect_tx_data() so that the table
being used is consistent.
Signed-off-by: NShanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: NHenry Zhang <hongx.c.zhang@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

Below warning is triggered sometimes at module removal time when
CONFIG_DMA_API_DEBUG is enabled. This should be caused by we didn't
unmap pending commands (enqueued, but no complete notification
received) for the Tx command queue.

[ 1583.107469] ------------[ cut here ]------------
[ 1583.107539] WARNING: at lib/dma-debug.c:688
dma_debug_device_change+0x13c/0x180()
[ 1583.107617] Hardware name: ...
[ 1583.107664] pci 0000:04:00.0: DMA-API: device driver has pending DMA
allocations while released from device [count=1]
[ 1583.107713] Modules linked in: ...
[ 1583.111661] Pid: 16970, comm: modprobe Tainted: G        W
2.6.34-rc1-wl #33
[ 1583.111727] Call Trace:
[ 1583.111779]  [<c02a281c>] ? dma_debug_device_change+0x13c/0x180
[ 1583.111833]  [<c02a281c>] ? dma_debug_device_change+0x13c/0x180
[ 1583.111908]  [<c0138e11>] warn_slowpath_common+0x71/0xd0
[ 1583.111963]  [<c02a281c>] ? dma_debug_device_change+0x13c/0x180
[ 1583.112016]  [<c0138ebb>] warn_slowpath_fmt+0x2b/0x30
[ 1583.112086]  [<c02a281c>] dma_debug_device_change+0x13c/0x180
[ 1583.112142]  [<c03e6c33>] notifier_call_chain+0x53/0x90
[ 1583.112198]  [<c03e1ebe>] ? down_read+0x6e/0x90
[ 1583.112271]  [<c015b229>] __blocking_notifier_call_chain+0x49/0x70
[ 1583.112326]  [<c015b26f>] blocking_notifier_call_chain+0x1f/0x30
[ 1583.112380]  [<c031931c>] __device_release_driver+0x8c/0xa0
[ 1583.112451]  [<c03193bf>] driver_detach+0x8f/0xa0
[ 1583.112538]  [<c0318382>] bus_remove_driver+0x82/0x100
[ 1583.112595]  [<c0319ad9>] driver_unregister+0x49/0x80
[ 1583.112671]  [<c024feb2>] ? sysfs_remove_file+0x12/0x20
[ 1583.112727]  [<c02aa292>] pci_unregister_driver+0x32/0x80
[ 1583.112791]  [<fc13a3c1>] iwl_exit+0x12/0x19 [iwlagn]
[ 1583.112848]  [<c017940a>] sys_delete_module+0x15a/0x210
[ 1583.112870]  [<c015a5db>] ? up_read+0x1b/0x30
[ 1583.112893]  [<c029600c>] ? trace_hardirqs_off_thunk+0xc/0x10
[ 1583.112924]  [<c0295ffc>] ? trace_hardirqs_on_thunk+0xc/0x10
[ 1583.112947]  [<c03e6a1f>] ? do_page_fault+0x1ff/0x3c0
[ 1583.112978]  [<c03e36f6>] ? restore_all_notrace+0x0/0x18
[ 1583.113002]  [<c016aa70>] ? trace_hardirqs_on_caller+0x20/0x190
[ 1583.113025]  [<c0102d58>] sysenter_do_call+0x12/0x38
[ 1583.113054] ---[ end trace fc23e059cc4c2ced ]---
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

Fix formatting on r8169 printk

Brandon Philips noted that I had a spacing issue in my printk for the
last r8169 patch that made it quite ugly.  Fix that up and add the PFX
macro to it as well so it looks like the other r8169 printks
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDimitris Michailidis <dm@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDimitris Michailidis <dm@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDimitris Michailidis <dm@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDimitris Michailidis <dm@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDimitris Michailidis <dm@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDimitris Michailidis <dm@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>