Always enable the service signal subclass mask bit in cr0, if pfault
is available. That way we use the normal cpu hotplug way to propagate
the subclass mask bit in cr0 instead of open coding it.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Choosing TMPFS_XATTR default N was switching off TMPFS_POSIX_ACL,
even if it had been Y in oldconfig; and Linus reports that PulseAudio
goes subtly wrong unless it can use ACLs on /dev/shm.

Make TMPFS_POSIX_ACL select TMPFS_XATTR (and depend upon TMPFS),
and move the TMPFS_POSIX_ACL entry before the TMPFS_XATTR entry,
to avoid asking unnecessary questions then ignoring their answers.
Signed-off-by: NHugh Dickins <hughd@google.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix this:

  drivers/video/mb862xx/mb862xx-i2c.c: In function 'mb862xx_i2c_wait_event':
  drivers/video/mb862xx/mb862xx-i2c.c:25: error: implicit declaration of function 'udelay'

caused by commit f8a6b1f4 ("video: mb862xx: add support for
controller's I2C bus adapter").
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/linux-2.6-nsfd:
  net: fix get_net_ns_by_fd for !CONFIG_NET_NS
  ns proc: Return -ENOENT for a nonexistent /proc/self/ns/ entry.
  ns: Declare sys_setns in syscalls.h
  net: Allow setting the network namespace by fd
  ns proc: Add support for the ipc namespace
  ns proc: Add support for the uts namespace
  ns proc: Add support for the network namespace.
  ns: Introduce the setns syscall
  ns: proc files for namespace naming policy.

Commit a71ae47a ("slub: Fix double bit unlock in debug mode")
removed the only goto to this label, resulting in

  mm/slub.c: In function '__slab_alloc':
  mm/slub.c:1834: warning: label 'unlock_out' defined but not used

fixed trivially by the removal of the label itself too.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (89 commits)
  bonding: documentation and code cleanup for resend_igmp
  bonding: prevent deadlock on slave store with alb mode (v3)
  net: hold rtnl again in dump callbacks
  Add Fujitsu 1000base-SX PCI ID to tg3
  bnx2x: protect sequence increment with mutex
  sch_sfq: fix peek() implementation
  isdn: netjet - blacklist Digium TDM400P
  via-velocity: don't annotate MAC registers as packed
  xen: netfront: hold RTNL when updating features.
  sctp: fix memory leak of the ASCONF queue when free asoc
  net: make dev_disable_lro use physical device if passed a vlan dev (v2)
  net: move is_vlan_dev into public header file (v2)
  bug.h: Fix build with CONFIG_PRINTK disabled.
  wireless: fix fatal kernel-doc error + warning in mac80211.h
  wireless: fix cfg80211.h new kernel-doc warnings
  iwlagn: dbg_fixed_rate only used when CONFIG_MAC80211_DEBUGFS enabled
  dst: catch uninitialized metrics
  be2net: hash key for rss-config cmd not set
  bridge: initialize fake_rtable metrics
  net: fix __dst_destroy_metrics_generic()
  ...

Fix up trivial conflicts in drivers/staging/brcm80211/brcmfmac/wl_cfg80211.c

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (75 commits)
  mmc: core: eMMC bus width may not work on all platforms
  mmc: sdhci: Auto-CMD23 fixes.
  mmc: sdhci: Auto-CMD23 support.
  mmc: core: Block CMD23 support for UHS104/SDXC cards.
  mmc: sdhci: Implement MMC_CAP_CMD23 for SDHCI.
  mmc: core: Use CMD23 for multiblock transfers when we can.
  mmc: quirks: Add/remove quirks conditional support.
  mmc: Add new VUB300 USB-to-SD/SDIO/MMC driver
  mmc: sdhci-pxa: Add quirks for DMA/ADMA to match h/w
  mmc: core: duplicated trial with same freq in mmc_rescan_try_freq()
  mmc: core: add support for eMMC Dual Data Rate
  mmc: core: eMMC signal voltage does not use CMD11
  mmc: sdhci-pxa: add platform code for UHS signaling
  mmc: sdhci: add hooks for setting UHS in platform specific code
  mmc: core: clear MMC_PM_KEEP_POWER flag on resume
  mmc: dw_mmc: fixed wrong regulator_enable in suspend/resume
  mmc: sdhi: allow powering down controller with no card inserted
  mmc: tmio: runtime suspend the controller, where possible
  mmc: sdhi: support up to 3 interrupt sources
  mmc: sdhi: print physical base address and clock rate
  ...

* 'kconfig-for-40' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
  xconfig: merge code path to conf_write()
  kconfig: do not record timestamp in .config
  gconfig: Hide unused left treeview when start up the interface
  gconfig: enable rules hint for main treeviews
  MAINTAINERS: Update KCONFIG entry
  kconfig-language: add to hints
  kconfig: Document the new "visible if" syntax
  kconfig: quiet commands when V=0
  kconfig: change update-po-config to reflect new layout of arch/um
  kconfig: make update-po-config work in KBUILD_OUTPUT
  kconfig: rearrange clean-files
  kconfig: change gconf to modify hostprogs-y like nconf and mconf
  kconfig: change qconf to modify hostprogs-y like nconf and mconf
  kconfig: only build kxgettext when needed
  nconfig: Silence unused return values from wattrset
  kconfig: Do not record timestamp in auto.conf and autoconf.h
  kconfig: get rid of unused flags
  kconfig: allow multiple inclusion of the same file
  kconfig: Avoid buffer underrun in choice input

* 'for-2.6.40' of git://git.kernel.org/pub/scm/linux/kernel/git/oleg/misc:
  signal: sys_pause() should check signal_pending()
  ptrace: ptrace_resume() shouldn't wake up !TASK_TRACED thread

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  hwmon: New driver for the SMSC EMC6W201
  hwmon: (abituguru) Depend on DMI
  hwmon: (it87) Use request_muxed_region
  hwmon: (sch5627) Trigger Vbat measurements
  hwmon: (sch5627) Add sch5627_send_cmd function
  i8k: Integrate with the hwmon subsystem
  hwmon: (max6650) Properly support the MAX6650
  hwmon: (max6650) Drop device detection
  Move ACPI power meter driver to hwmon
  hwmon: (f71882fg) Add support for F71808A
  hwmon: (f71882fg) Split has_beep in fan_has_beep and temp_has_beep
  hwmon: (asc7621) Drop duplicate dependency
  hwmon: (jc42) Change detection class
  hwmon: Add driver for AMD family 15h processor power information
  hwmon: (k10temp) Add support for Fam15h (Bulldozer)
  hwmon: Use helper functions to set and get driver data
  i8k: Avoid lahf in 64-bit code

* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile: (26 commits)
  arch/tile: prefer "tilepro" as the name of the 32-bit architecture
  compat: include aio_abi.h for aio_context_t
  arch/tile: cleanups for tilegx compat mode
  arch/tile: allocate PCI IRQs later in boot
  arch/tile: support signal "exception-trace" hook
  arch/tile: use better definitions of xchg() and cmpxchg()
  include/linux/compat.h: coding-style fixes
  tile: add an RTC driver for the Tilera hypervisor
  arch/tile: finish enabling support for TILE-Gx 64-bit chip
  compat: fixes to allow working with tile arch
  arch/tile: update defconfig file to something more useful
  tile: do_hardwall_trap: do not play with task->sighand
  tile: replace mm->cpu_vm_mask with mm_cpumask()
  tile,mn10300: add device parameter to dma_cache_sync()
  audit: support the "standard" <asm-generic/unistd.h>
  arch/tile: clarify flush_buffer()/finv_buffer() function names
  arch/tile: kernel-related cleanups from removing static page size
  arch/tile: various header improvements for building drivers
  arch/tile: disable GX prefetcher during cache flush
  arch/tile: tolerate disabling CONFIG_BLK_DEV_INITRD
  ...

Merge branch 'for-torvalds' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson

* 'for-torvalds' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
  mach-ux500: voltage domain regulators for DB8500
  cpufreq: make DB8500 cpufreq driver compile
  cpufreq: update DB8500 cpufreq driver
  mach-ux500: move CPUfreq driver to cpufreq subsystem
  mfd: add DB5500 PRCMU driver
  mfd: update DB8500 PRCMU driver
  mach-ux500: move the DB8500 PRCMU driver to MFD
  mach-ux500: make PRCMU base address dynamic
  mach-ux500: rename PRCMU driver per SoC
  mach-ux500: update ASIC version detection
  mach-ux500: update SoC and board IRQ handling
  mach-ux500: update the DB5500 register file
  mach-ux500: update the DB8500 register file

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin: (37 commits)
  Blackfin: use new common PERCPU_INPUT define
  MAINTAINERS: Fix Analog Devices mailinglist address
  Blackfin: boards: update ASoC resources after machine driver overhaul
  Blackfin: work around anomaly 05000480
  Blackfin: fix addr type with bfin_write_{or,and} helpers
  Blackfin: convert /proc/sram to seq_file
  Blackfin: switch /proc/gpio to seq_file
  Blackfin: fix indentation with bfin_read() helper
  Blackfin: convert old cpumask API to new one
  Blackfin: don't touch task->cpus_allowed directly
  Blackfin: don't touch cpu_possible_map and cpu_present_map directly
  Blackfin: bf548-ezkit/bf561-ezkit: update nor flash layout
  Blackfin: initial perf_event support
  Blackfin: update anomaly lists to latest public info
  Blackfin: use on-chip reset func with newer parts
  Blackfin: bf533-stamp/bf537-stamp: drop ad1980 from defconfigs
  Blackfin: optimize MMR reads during startup a bit
  Blackfin: bf537: demux port H mask A and emac rx ints
  Blackfin: bf537: fix excessive gpio int demuxing
  Blackfin: bf54x: drop unused pm gpio handling
  ...

* 'rmobile-latest' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (34 commits)
  ARM: mach-shmobile: mackerel: add renesas_usbhs support for USB1
  ARM: mach-shmobile: Correct the G4EVM SDHI0 I/O range.
  ARM: arch-shmobile: sh7372: add renesas_usbhs irq support
  ARM: mach-shmobile: sh73a0: mark DMA slave ID 0 as invalid
  ARM: mach-shmobile: mark DMA slave ID 0 as invalid
  ARM: mach-shmobile: Enable DMAEngine for SDHI on AG5EVM
  ARM: mach-shmobile: Enable DMAEngine for MMCIF on AG5EVM
  ARM: mach-shmobile: sh73a0 DMA Engine support for SY-DMAC
  dmaengine: shdma: Update SH_DMAC_MAX_CHANNELS to 20
  dmaengine: shdma: Fix SH_DMAC_MAX_CHANNELS handling
  dmaengine: shdma: Make second memory window optional
  ARM: mach-shmobile: Tidy up after SH7372 pm changes.
  ARM: mach-shmobile: sh7372 Core Standby CPUIdle
  ARM: mach-shmobile: CPUIdle support
  ARM: mach-shmobile: sh7372 Core Standby Suspend-to-RAM
  ARM: mach-shmobile: Suspend-to-RAM support
  mailmap: Add entry for Damian Hobson-Garcia.
  ARM: switch mackerel to dynamically manage the platform camera
  ARM: mach-shmobile: Add SDHI support for AG5EVM and sh73a0
  ARM: arch-shmobile: Use multiple irq vectors for SDHI
  ...

commit 9ec26907 ("timerfd: Manage cancelable timers in timerfd")
introduced a CONFIG_HIGHRES_TIMERS (should be CONFIG_HIGH_RES_TIMERS)
typo, which caused applications depending on CLOCK_REALTIME timers to
become sluggy due to the fact that the time base of the realtime
timers was not updated when the wall clock time was set.

This causes anything from 100% CPU use for some applications to odd
delays and hickups.
Reported-bisected-and-tested-by: NAnca Emanuel <anca.emanuel@gmail.com>
Tested-by: NLinus Torvalds <torvalds@linux-foundation.org>
Fatfingered-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Improves the documentation about how IGMP resend parameter
works, fix two missing checks and coding style issues.
Signed-off-by: NFlavio Leitner <fbl@redhat.com>
Acked-by: NRick Jones <rick.jones2@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This soft lockup was recently reported:

[root@dell-per715-01 ~]# echo +bond5 > /sys/class/net/bonding_masters
[root@dell-per715-01 ~]# echo +eth1 > /sys/class/net/bond5/bonding/slaves
bonding: bond5: doing slave updates when interface is down.
bonding bond5: master_dev is not up in bond_enslave
[root@dell-per715-01 ~]# echo -eth1 > /sys/class/net/bond5/bonding/slaves
bonding: bond5: doing slave updates when interface is down.

BUG: soft lockup - CPU#12 stuck for 60s! [bash:6444]
CPU 12:
Modules linked in: bonding autofs4 hidp rfcomm l2cap bluetooth lockd sunrpc
be2d
Pid: 6444, comm: bash Not tainted 2.6.18-262.el5 #1
RIP: 0010:[<ffffffff80064bf0>]  [<ffffffff80064bf0>]
.text.lock.spinlock+0x26/00
RSP: 0018:ffff810113167da8  EFLAGS: 00000286
RAX: ffff810113167fd8 RBX: ffff810123a47800 RCX: 0000000000ff1025
RDX: 0000000000000000 RSI: ffff810123a47800 RDI: ffff81021b57f6f8
RBP: ffff81021b57f500 R08: 0000000000000000 R09: 000000000000000c
R10: 00000000ffffffff R11: ffff81011d41c000 R12: ffff81021b57f000
R13: 0000000000000000 R14: 0000000000000282 R15: 0000000000000282
FS:  00002b3b41ef3f50(0000) GS:ffff810123b27940(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 00002b3b456dd000 CR3: 000000031fc60000 CR4: 00000000000006e0

Call Trace:
 [<ffffffff80064af9>] _spin_lock_bh+0x9/0x14
 [<ffffffff886937d7>] :bonding:tlb_clear_slave+0x22/0xa1
 [<ffffffff8869423c>] :bonding:bond_alb_deinit_slave+0xba/0xf0
 [<ffffffff8868dda6>] :bonding:bond_release+0x1b4/0x450
 [<ffffffff8006457b>] __down_write_nested+0x12/0x92
 [<ffffffff88696ae4>] :bonding:bonding_store_slaves+0x25c/0x2f7
 [<ffffffff801106f7>] sysfs_write_file+0xb9/0xe8
 [<ffffffff80016b87>] vfs_write+0xce/0x174
 [<ffffffff80017450>] sys_write+0x45/0x6e
 [<ffffffff8005d28d>] tracesys+0xd5/0xe0

It occurs because we are able to change the slave configuarion of a bond while
the bond interface is down.  The bonding driver initializes some data structures
only after its ndo_open routine is called.  Among them is the initalization of
the alb tx and rx hash locks.  So if we add or remove a slave without first
opening the bond master device, we run the risk of trying to lock/unlock a
spinlock that has garbage for data in it, which results in our above softlock.

Note that sometimes this works, because in many cases an unlocked spinlock has
the raw_lock parameter initialized to zero (meaning that the kzalloc of the
net_device private data is equivalent to calling spin_lock_init), but thats not
true in all cases, and we aren't guaranteed that condition, so we need to pass
the relevant spinlocks through the spin_lock_init function.

Fix it by moving the spin_lock_init calls for the tx and rx hashtable locks to
the ndo_init path, so they are ready for use by the bond_store_slaves path.

Change notes:
v2) Based on conversation with Jay and Nicolas it seems that the ability to
enslave devices while the bond master is down should be safe to do.  As such
this is an outlier bug, and so instead we'll just initalize the errant spinlocks
in the init path rather than the open path, solving the problem.  We'll also
remove the warnings about the bond being down during enslave operations, since
it should be safe

v3) Fix spelling error
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
Reported-by: jtluka@redhat.com
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: nicolas.2p.debian@gmail.com
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit e67f88dd (dont hold rtnl mutex during netlink dump callbacks)
missed fact that rtnl_fill_ifinfo() must be called with rtnl held.

Because of possible deadlocks between two mutexes (cb_mutex and rtnl),
its not easy to solve this problem, so revert this part of the patch.

It also forgot one rcu_read_unlock() in FIB dump_rules()

Add one ASSERT_RTNL() in rtnl_fill_ifinfo() to remind us the rule.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
CC: Patrick McHardy <kaber@trash.net>
CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the PCI ID of Fujitsu 1000base-SX NIC to tg3 driver.
Tested to detect the card, MAC and serdes, not tested with link at the
moment since I have no fiber switch here. I did not add new constants to
the pci_ids.h header file since these constants are used only here.
Signed-off-by: NMeelis Roos <mroos@linux.ee>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit eeaeb068 (sch_sfq: allow big packets and be fair),
sfq_peek() can return a different skb that would be normally dequeued by
sfq_dequeue() [ if current slot->allot is negative ]

Use generic qdisc_peek_dequeued() instead of custom implementation, to
get consistent result.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
CC: Jarek Poplawski <jarkao2@gmail.com>
CC: Patrick McHardy <kaber@trash.net>
CC: Jesper Dangaard Brouer <hawk@diku.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

[2nd try ... 1st attempt didn't make it to netdev mailing list]

A quick google search reveals that people with this card are blacklisting it
in the initramfs and in the module blacklist based on a statement that it
is unsupported. Since the older Digium is also unsupported I'm pretty
confident that this newer card is also not supported.

lspci -xxx -vv shows

04:07.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface
        Subsystem: Device b100:0003
P.

----8<----
The Asterisk Voice Card, DIGIUM TDM400P is unsupported by the netjet driver.
Blacklist it like the Digium X100P/X101P card.
Signed-off-by: NPrarit Bhargava <prarit@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On ARM, memory accesses through packed pointers behave in unexpected
ways in GCC releases 4.3 and higher; see https://lkml.org/lkml/2011/2/2/163
for discussion.

In this particular case, 32-bit I/O registers are accessed bytewise,
causing incorrect setting of the DMA address registers which in turn
leads to an error interrupt storm that brings the system to a halt.

Since the mac_regs structure does not need any packing anyway, this patch
simply removes the attribute to fix the issue.
Signed-off-by: NUlrich Hecht <uli@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Konrad reports:
[    0.930811] RTNL: assertion failed at /home/konrad/ssd/linux/net/core/dev.c (5258)
[    0.930821] Pid: 22, comm: xenwatch Not tainted 2.6.39-05193-gd762f438 #1
[    0.930825] Call Trace:
[    0.930834]  [<ffffffff8143bd0e>] __netdev_update_features+0xae/0xe0
[    0.930840]  [<ffffffff8143dd41>] netdev_update_features+0x11/0x30
[    0.930847]  [<ffffffffa0037105>] netback_changed+0x4e5/0x800 [xen_netfront]
[    0.930854]  [<ffffffff8132a838>] xenbus_otherend_changed+0xa8/0xb0
[    0.930860]  [<ffffffff8157ca99>] ? _raw_spin_unlock_irqrestore+0x19/0x20
[    0.930866]  [<ffffffff8132adfe>] backend_changed+0xe/0x10
[    0.930871]  [<ffffffff8132875a>] xenwatch_thread+0xba/0x180
[    0.930876]  [<ffffffff810a8ba0>] ? wake_up_bit+0x40/0x40
[    0.930881]  [<ffffffff813286a0>] ? split+0xf0/0xf0
[    0.930886]  [<ffffffff810a8646>] kthread+0x96/0xa0
[    0.930891]  [<ffffffff815855a4>] kernel_thread_helper+0x4/0x10
[    0.930896]  [<ffffffff815846b3>] ? int_ret_from_sys_call+0x7/0x1b
[    0.930901]  [<ffffffff8157cf61>] ? retint_restore_args+0x5/0x6
[    0.930906]  [<ffffffff815855a0>] ? gs_change+0x13/0x13

This update happens in xenbus watch callback context and hence does not already
hold the rtnl. Take the lock as necessary.
Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Tested-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If an ASCONF chunk is outstanding, then the following ASCONF
chunk will be queued for later transmission. But when we free
the asoc, we forget to free the ASCONF queue at the same time,
this will cause memory leak.
Signed-off-by: NWei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the device passed into dev_disable_lro is a vlan, then repoint the dev
poniter so that we actually modify the underlying physical device.
Signed-of-by: NNeil Horman <nhorman@tuxdriver.com>
CC: davem@davemloft.net
CC: bhutchings@solarflare.com
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Migrate is_vlan_dev() to if_vlan.h so that core networkig can use it
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
CC: davem@davemloft.net
CC: bhutchings@solarflare.com
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CMD19 -- The offical way to validate bus widths from the JEDEC spec
does not work on all platforms.  Some platforms that use PCI/PCIe
to connect their SD controllers are known to fail.

If the quirk MMC_BUS_WIDTH_TEST is not defined we try to figure out
the bus width by reading the ext_csd at different bus widths and
compare this against the ext_csd read in 1 bit mode.  If no ext_csd
is available we default to 1 bit operations.

Code has been tested on mmp2 against 8 bit eMMC and Transcend 2GB
card that is known to not work in 4 bit mode.  The physical pins
on the card are not present to support 4 bit operation.
Signed-off-by: NPhilip Rakity <prakity@marvell.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Fixes bugs in Auto-CMD23 feature enable decision. Auto-CMD23
should be enabled if host is >= v3, and SDMA is not in use.

USE_ADMA | USE_SDMA | Auto-CMD23
---------+----------+-----------
    0    |    0     |     1
---------+----------+-----------
    0    |    1     |     0
---------+----------+-----------
    1    |    0     |     1
---------+----------+-----------
    1    |    1     |     1
Signed-off-by: NAndrei Warkentin <andreiw@motorola.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Enables Auto-CMD23 support where available (SDHCI 3.0 controllers)
Signed-off-by: NAndrei Warkentin <andreiw@motorola.com>
Tested-by: NArindam Nath <arindam.nath@amd.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

SD cards operating at UHS104 or better support SET_BLOCK_COUNT.
Signed-off-by: NAndrei Warkentin <andreiw@motorola.com>
Reviewed-by: NArindam Nath <arindam.nath@amd.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Implements support for multiblock transfers bounded
by SET_BLOCK_COUNT (CMD23).
Signed-off-by: NAndrei Warkentin <andreiw@motorola.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

CMD23-prefixed instead of open-ended multiblock transfers
have a performance advantage on some MMC cards.
Signed-off-by: NAndrei Warkentin <andreiw@motorola.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

With this change, you can (and should) build with ARCH=tilepro for the
current 32-bit chips.  Building with ARCH=tile continues to work, but
we've renamed the defconfig file to tilepro_defconfig for consistency.
Signed-off-by: NChris Metcalf <cmetcalf@tilera.com>

* 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
  export_report: use warn() to issue WARNING, so they go to stderr
  export_report: sort SECTION 2 output
  export_report: do collectcfiles work in perl itself
  kbuild: make versioncheck work in KBUILD_OUTDIR
  kbuild: make includecheck work in KBUILD_OUTDIR
  kbuild: make headerdep work in KBUILD_OUTDIR
  kbuild: add targets to PHONY
  kbuild: don't warn about include/linux/version.h not including itself
  eradicate bashisms in scripts/patch-kernel

* 'packaging' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
  kbuild: Create a kernel-headers RPM
  rpm-pkg: Fix when current directory is a symlink
  Replace '-' in kernel version with '_'

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (23 commits)
  ceph: fix cap flush race reentrancy
  libceph: subscribe to osdmap when cluster is full
  libceph: handle new osdmap down/state change encoding
  rbd: handle online resize of underlying rbd image
  ceph: avoid inode lookup on nfs fh reconnect
  ceph: use LOOKUPINO to make unconnected nfs fh more reliable
  rbd: use snprintf for disk->disk_name
  rbd: cleanup: make kfree match kmalloc
  rbd: warn on update_snaps failure on notify
  ceph: check return value for start_request in writepages
  ceph: remove useless check
  libceph: add missing breaks in addr_set_port
  libceph: fix TAG_WAIT case
  ceph: fix broken comparison in readdir loop
  libceph: fix osdmap timestamp assignment
  ceph: fix rare potential cap leak
  libceph: use snprintf for unknown addrs
  libceph: use snprintf for formatting object name
  ceph: use snprintf for dirstat content
  libceph: fix uninitialized value when no get_authorizer method is set
  ...

This is a new driver for the SMSC EMC6W201 hardware monitoring device.
The device is functionally close to the EMC6D100 series, but is
register-incompatible.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Tested-by: NHarry G McGavran Jr <w5pny@arrl.net>
Tested-by: NJeff Rickman <jrickman@myamigos.us>
Acked-by: NGuenter Roeck <guenter.roeck@ericsson.com>

The abituguru drivers are only built on X86, where DMI support is now
enabled by default. So let these drivers depend on DMI, for the
following gains:
* Robustness and safety. Detection of these devices is weak and uses
  non-standard methods, it should really be limited to Abit boards
  unless the user explicitly asks otherwise.
* Code simplicity. The code is easier to read without ifdefs.
* Better build testing coverage. Now there's only one way to build the
  drivers, so no risk of build failure on exotic systems.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Acked-by: NAlistair John Strachan <alistair@devzero.co.uk>
Acked-by: NHans de Goede <hdegoede@redhat.com>

Serialize access to the hardware by using "request_muxed_region" macro
defined by Alan Cox. Call to this macro will hold off the requestor if
the resource is currently busy. "superio_enter" will return an error
if call to "request_muxed_region" fails. Rest of the code change is to
ripple an error return from superio_enter to the top level.
Signed-off-by: NNat Gurumoorthy <natg@google.com>
Acked-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>