This header file exists only for some hacks to adapt alsa-driver
tree.  It's useless for building in the kernel.  Let's move a few
lines in it to sound/core.h and remove it.
With this patch, sound/driver.h isn't removed but has just a single
compile warning to include it.  This should be really killed in
future.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Added AC_VERB_GET_DIGI_CONVERT_2 and renamed AC_VERB_GET_DIGI_CONVERT to
AC_VERB_GET_DIGI_CONVERT_1 to stay consistent with the SET variants. Added
AC_VERB_GET_GPIO_UNSOLICITED_RSP_MASK, AC_VERB_SET_GPIO_UNSOLICITED_RSP_MASK,
and AC_PINCAP_LR_SWAP. The missing fields were listed in the ALC883 datasheet
rev 1.3.
Signed-off-by: NAndrew Paprocki <andrew@ishiboo.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Check the value ranges in ctl put callbacks properly so that
invalid values won't be stored or written to registers.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Some small improvements on autocfg stuff:
- sort HP pins by sequence number, too
- move sole mic pin to AUTO_PIN_MIC instead of AUTO_PIN_FRONT_MIC
- ditto for line-in pin
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Added the missing STAC9228 DMIC support.
Also added a new vendor id tag for IDT.
Signed-off-by: NMatthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

The recent addition of checking PINCAP for EAPD seems to break some
systems due to unexpected response from the codec chip.  We shouldn't
issue GET_PINCAP verb to non-PIN widgets.  Now checks the widget type
before checking EAPD bit.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

AD1986A has a hardware problem that it cannot share a stream with
multiple pins properly.  The problem occurs e.g. when a volume is changed
during playback.
So far, hda-intel driver unconditionally assigns the stream to multiple
output pins in copy-front mode, and this should be avoided for AD1986A
codec.
The original fix patch was by zhejiang <zhe.jiang@intel.com>.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Fixed the build error from patch_sigmatel.c when built without
CONFIG_SND_HDA_GENERIC by defining a dummy function to return error.
Also, clean up hda_codec.c by removing unneeded ifdefs (the compiler
will optimize out).
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Fix the output of Gateway laptops with STAC9200 codec chip.
They require the EAPD control for some pins.  These pins shouldn't be
powered down.
To enable EAPD control, a new model 'gateway' was added to STAC9200.
The known PCI SSIDs are included in the quirk list.
The fix was originally suggested by Brian Hinz, in ALSA bug#2948.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Added zero checks in input-mux helper functions to avoid Oops.
Some devices may have no input pins while the driver registers
control elements calling these functions.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Added CONFIG_SND_AC97_POWER_SAVE_DEFAULT and CONFIG_SND_HDA_POWER_SAVE_DEFAULT
Kconfig options as the default values for power-saving mode of AC97 and
HD-audio drivers, respectively.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

When modem is disabled in the BIOS, detection of the number of codecs
always fails after booting if STATESTS is not cleared first.
This patch fixes this problem and also adds an error check in a place
where a read error would lead to a very large number of pointless loops.
Signed-off-by: NDanny Tholen <obiwan@mailmij.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Comment in hda_intel.c states that 'the explicit resume is needed only
when POWER_SAVE isn't set', but this is not true.
There is no code that will automaticly power up the codec on resume,
but only code that powers it up when user accesses it. So if user
leaves a sound playing, codec will not be powered
To fix that I check if there are any codecs that should be powered
codec->power_count, and if so I power them up together with main
controller.
Signed-off-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

codec->power_transition is supposed to be true while codec is going
to be shut off if in the mean time somebody calls snd_hda_power_up,
hda_power_work will not shut down the codec, but nether will clear
codec->power_transition, thus it stays on forever. Fix this.
Signed-off-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

gcc-3.x doesn't like forward inlining:
  CC [M]  sound/pci/hda/hda_codec.o
sound/pci/hda/hda_codec.c: In function 'snd_hda_codec_free':
sound/pci/hda/hda_codec.c:517: sorry, unimplemented: inlining failed in call to 'free_hda_cache': function body not available
sound/pci/hda/hda_codec.c:534: sorry, unimplemented: called from here
sound/pci/hda/hda_codec.c:517: sorry, unimplemented: inlining failed in call to 'free_hda_cache': function body not available
sound/pci/hda/hda_codec.c:535: sorry, unimplemented: called from here
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Avoid unnecessary work scheduling for power-off.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Added flush_scheduled_work() in snd_hda_codec_free() to make sure that
the all work is gone.  Also, optimized the condition to schedule the
delayed work in snd_hda_power_down().
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

In the power-saving mode, the suspend is done dynamically at power-down.
So we don't have to call suspend stuff explicitly if it's already
powered down.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

codec->patch_ops.init can be NULL.  Check before calling it.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

The controller power wasn't turned on properly at resume due to the
power-saving patch.  Now fixed.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Added CONFIG_SND_HDA_POWER_SAVE kconfig.  It's an experimental option
to achieve an aggressive power-saving.  With this option, the driver
will turn on/off the power of each codec and controller chip dynamically
on demand.
The patch introduces a new module option 'power_save'.  It specifies
the second of time-out for automatic power-down.  As default, it's
10 seconds.  Setting 0 means to suppress the power-saving feature.
The codec may have analog-input loopbacks, which are usually represented
by mixer elements such as 'Mic Playback Switch' or 'CD Playback Switch'.
When these are on, we cannot turn off the mixer and the codec chip has
to be kept on.  For bookkeeping these states, a new codec-callback is
introduced.
For the bus-controller side, a new callback pm_notify is introduced,
which can be used to turn on/off the contoller appropriately.
Note that this power-saving might cause slight click-noise at
power-on/off.  Also, it might take some time to wake up the codec, and
might even drop some tones at the very beginning.  This seems to be the
side-effect of turning off the controller chip.
This turn-off of the controller can be disabled by undefining
HDA_POWER_SAVE_RESET_CONTOLLER in hda_intel.c.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Added snd_hda_codec_amp_stereo() function that changes both of stereo
channels with the same mask and value bits.  It simplifies most of
amp-handling codes.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

So far, the driver looked the table of snd_kcontrol_new used for creating
mixer elements and forces to call each of its put callbacks in PM resume
code.  This is too ugly and hackish.
Now, the resume is simplified using the codec amp and command register
caches.  The driver simply restores the values that have been written
in the cache table.  With this simplification, most codec support codes
don't require any special resume callback.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

This patch adds the cache for codec command registers.
snd_hda_codec_write_cache() and snd_hda_sequence_write_cache() do
the write operations with caching, which values can be resumed via
snd_hda_codec_resume_cache().
The patch introduces only the framework, and no codec code is using
this cache yet.  It'll be implemented in the following patch.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Rewrite the code to handle amp cache and hash tables to be more
generic.  This routine will be used by the register caches in the
next patch.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Some functions in hda_codec.c are called from patch ops, which are
kept in the codec instance even after initialization.  Thus they
shouldn't be marked as __devinit.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Create kernel configs to choose the codec support codes to build.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Added callbacks for a generic bind-control of mixer elements.
This can be used for creating a mixer element controlling multiple
widgets at the same time.  Two macros, HDA_BIND_VOL() and HDA_BIND_SW(),
are introduced for creating bind-volume and bind-switch, respectively.
It taks the mixer element name and struct hda_bind_ctls pointer, which
contains the real control callbacks in ops field and long array for
private_value of each bound widget.
All widgets have to be the same type (i.e. the same amp capability).
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Added a hwdep interface for each codec (enabled per kconfig).
This interface can be used for reading/writing HD-audio verbs
and other purposes as future extensions.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Clean up codes using the new common snd_ctl_boolean_*_info() callbacks.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

STAC922x provides the capture boost level up to 4, but actually it
works only up to 2.  Since the range of the mixer is automatically
defined from amp-capability bits, we need to override the value
beforehand.  snd_hda_override_amp_caps() is introduced for this
purpose.
The function patch_stac922x() calls this for NID 0x12 (Mux Capture
Volume).  This should fix another recording problem on Intel Macs.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

In some cases, mixer elements return -EINVAL because it couldn't
obtain proper amp_cap bits.  The patch improves the robustness,
trying the amp_cap query again in such a case.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Some verb tables (such as an Asus VT sent by IDT) contain only speaker
outs in the default pin configs, and no line-outs. In such a case the
speaker sequence numbers have to be used to order the speaker out
pins, just as is being done for line-out pins. Then, when speaker-outs
are copied to line-outs, the line-outs will be ordered properly.
Signed-off-by: NSteve Longerbeam <stevel@embeddedalley.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Prefer the name of audio codecs as the mixer name even if
modem codecs are probed before the audio codecs.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Added line_out_type field to auto_pin_cfg struct to provide the
pin type of default line_outs.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Fix the auto-configuration of 8-channel devices.  The sequence numbers
of usual 7.1 outputs are: 0/1/2/4 = Front/CLFE/Rear/Side
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Trivial code clean-ups to follow the standard coding styles.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Merge hda-codec module to a single hda-intel module since this is the
only user right now.  Although hda-codec stuff is designed to be used
universally from different controller drivers, currently only one
controller interface (and compatibles) are used.  So, let's merge them
to a single module to save memory.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Allow opening the dedicated SPDIF stream while running on analog dup
mode.  Then the SPDIF stream is once reset and assigned for the new
stream.  It's useful for exclusive SPDIF output like AC3/DTS.
(In the former version, you had to close once the analog stream to
 play the exclusive digital stream.)
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Added the support of 96kHz sample rate back.  Although the rate isn't
listed in the ACC_PAR_PCM bits but si3054 codecs do support this rate
explicitly.  Now fixed the deteciton code not to check this extra bit.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>