Use the constants defined in include/dt-bindings/interrupt-controller/
to enhance readability.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Use standard GPIO constants to enhance the readability of DT GPIOs.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Replace /include/ by #include for OMAP2+ DT, in order to use the
C pre-processor, making use of #define features possible.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

GPMC controller on AM335x-EVM has a NAND flash connected to it.
This patch updates following in am335x-evm.dts:
- adds nandflash specific pin-mux configs
- adds nand node as child of GPMC contoller, with information about
  NAND flash interface, NAND partition table, ECC scheme, elm handle id.
- updates GPMC node for newer GPMC DT properties added in linux-3.10.
Signed-off-by: NPhilip Avinash <avinashphilip@ti.com>
Signed-off-by: NGupta, Pekon <pekon@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

ELM hardware engine is used for locating bit-flips in NAND data
This patch is required for working of hardware based NAND ECC schemes
with DT support.
Signed-off-by: NPhilip Avinash <avinashphilip@ti.com>
Acked-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NPekon Gupta <pekon@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

The IGEP COM Module has an 512MB NAND flash memory.

Add a device node for this NAND and its partition layout.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

The IGEPv2 board has an 512MB NAND flash memory.

Add a device node for this NAND and its partition layout.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

The IGEPv2 board has an SMSC LAN9221i ethernet chip connected to
the OMAP3 processor though the General-Purpose Memory Controller.

This patch adds a device node for the ethernet chip as a GPMC child
and all its dependencies (regulators, GPIO and pin muxs).
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

xdma_event_intr1.clkout2 pad can be used to source clock
from either 32K OSC or any of the PLL (except MPU) outputs.
On the existing AM335x based boards (EVM, EVM-SK and Bone),
this pad is used to feed the clock to audio codes.

So, this patch configures the pinmux to get clkout2 on the pad.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Add pin control binding for UART0 device nodes in all
board specific DT files.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Acked-by: NMatt Porter <mporter@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

With DT support, where naming convention is based on base-addr
and not id, so we should follow TRM/Spec numbering label.

This patch changes UART numbering as per TRM, as uart0-5.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Acked-by: NMatt Porter <mporter@ti.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Now gpio-leds driver is using devm_pinctrl_get_select_default()
api to set default pinmux configuration required for the
functionality of the driver, so this patch moves respective
pinctrl binding inside leds node.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Add pin control binding for I2C device nodes in all
board specific DT files (as per current usage),

EVM: Both i2c0 and i2c1
EVM-SK and Bone: Only i2c0
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Acked-by: NMatt Porter <mporter@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

The carveouts that have been reserved for multimedia usecases
are not being used currently by any driver and so have been
cleaned up. Memory will be allocated runtime through CMA for
enabling the multimedia usecases.
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

This patch makes legacy code on suspend/resume path being executed
conditionally, on non-DT platforms only, to fix suspend/resume of
DT-enabled systems, for which the code is inappropriate.
Signed-off-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
[olof: add #include <linux/of.h>]
Signed-off-by: NOlof Johansson <olof@lixom.net>

In prima2, some functions of checking DT is registered in initcall
level. If it doesn't match the compatible name of sirf, kernel
will panic. It blocks the usage of multiplatform on other verndor.

The error message is in below.

Knic - not syncing: unable to find compatible pwrc node in dtb
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.10.0-rc3-00006-gd7f26ea-dirty #86
[<c0013adc>] (unwind_backtrace+0x0/0xf8) from [<c0011430>] (show_stack+0x10/0x1)
[<c0011430>] (show_stack+0x10/0x14) from [<c026f724>] (panic+0x90/0x1e8)
[<c026f724>] (panic+0x90/0x1e8) from [<c03267fc>] (sirfsoc_of_pwrc_init+0x24/0x)
[<c03267fc>] (sirfsoc_of_pwrc_init+0x24/0x58) from [<c0320864>] (do_one_initcal)
[<c0320864>] (do_one_initcall+0x90/0x150) from [<c0320a20>] (kernel_init_freeab)
[<c0320a20>] (kernel_init_freeable+0xfc/0x1c4) from [<c026b9e8>] (kernel_init+0)
[<c026b9e8>] (kernel_init+0x8/0xe4) from [<c000e158>] (ret_from_fork+0x14/0x3c)
Signen-off-by: NHaojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

If the early MMU mapping of the UART happens to get booted out of the
TLB between the start of paging_init() and when we finally re-add the
UART at the very end of s3c_init_cpu(), we'll get a hang at bootup if
we've got early_printk enabled.  Avoid this hang by calling
debug_ll_io_init() early.

Without this patch, you can reliably reproduce a hang when early
printk is enabled by adding flush_tlb_all() at the start of
exynos_init_io().  After this patch the hang goes away.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Printing low-level debug messages make an assumption that the specified
UART port has been preconfigured by the bootloader. Incorrectly
specified UART port results in system getting stalled while printing the
message "Uncompressing Linux... done, booting the kernel"
This UART port number is specified through S3C_LOWLEVEL_UART_PORT. Since
the UART port might different for different board, it is not possible to
specify it correctly for every board that use a common defconfig file.

Calling this print subroutine only when DEBUG_LL fixes the problem. By
disabling DEBUG_LL in default config file, we would be able to boot
multiple boards with different default UART ports.

With this current approach, we miss the print "Uncompressing Linux...
done, booting the kernel." when DEBUG_LL is not defined.
Signed-off-by: NTushar Behera <tushar.behera@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The ranges DT entry needed by the PCIe controller is defined at the
SoC .dtsi level. However, some boards have a NOR flash, and to support
it, they need to override the SoC-level ranges property to add an
additional range. Since PCIe and NOR support came separately, some
boards were not properly changed to include the PCIe range in their
ranges property at the .dts level.

This commit fixes those platforms.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

MPP_F6281_MASK would be previously be returned when on mv88f6282,
which would disallow some valid MPP configurations.

Commit 830f8b91 (arm: plat-orion: fix printing of "MPP config
unavailable on this hardware") made this problem visible as an invalid
MPP configuration is now correctly detected and not applied.
Signed-off-by: NNicolas Schichan <nschichan@freebox.fr>
Cc: <stable@vger.kernel.org> # v3.9.x
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

omap36xx_pwrdn_clk_enable_with_hsdiv_restore expects the parent hw of
the clock to be a clk_hw_omap. However, looking at cclock3xxx_data.c,
all concerned clock have parent defined as clk_divider.  Fix the
function to use clk_divider.  Tested with 3.9 on dm3730.
Signed-off-by: NJean-Philippe François <jp.francois@cynove.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Since the introduction of preemptible mmu_gather TLB fast mode has been
broken. TLB fast mode relies on there being absolutely no concurrency;
it frees pages first and invalidates TLBs later.

However now we can get concurrency and stuff goes *bang*.

This patch removes all tlb_fast_mode() code; it was found the better
option vs trying to patch the hole by entangling tlb invalidation with
the scheduler.

Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tony Luck <tony.luck@intel.com>
Reported-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

__my_cpu_offset is non-volatile, since we want its value to be cached
when we access several per-cpu variables in a row with preemption
disabled. This means that we rely on preempt_{en,dis}able to hazard
with the operation via the barrier() macro, so that we can't end up
migrating CPUs without reloading the per-cpu offset.

Unfortunately, GCC doesn't treat a "memory" clobber on a non-volatile
asm block as a side-effect, and will happily re-order it before other
memory clobbers (including those in prempt_disable()) and cache the
value. This has been observed to break the cmpxchg logic in the slub
allocator, leading to livelock in kmem_cache_alloc in mainline kernels.

This patch adds a dummy memory input operand to __my_cpu_offset,
forcing it to be ordered with respect to the barrier() macro.

Cc: <stable@vger.kernel.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The previous mask values for the legacy ARM CPU IDs were conflicting
with the CPU ID assignments for late-generation CPUs (like the
Qualcomm MSM/QSD or Broadcom Brahma-15 processors). This change
corrects the legacy ARM CPU ID value so that the jump table can
fall-through to the appropriate cache maintenance / MMU functions.
Signed-off-by: NMarc C <marc.ceeeee@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

In August 2012, Matthew Gretton-Dann checked a change into binutils
labelled "Error on obsolete & warn on deprecated registers", apparently as
part of ARMv8 support. Apparently, this was supposed to emit the message
"Warning: This coprocessor register access is deprecated in ARMv8" when
using certain mcr/mrc instructions and building for ARMv8. Unfortunately,
the message that is actually emitted appears to be '(null)', which is
less helpful in comparison.

Even more unfortunately, this is biting us on every single kernel
build with a new gas, because arch/arm/boot/compressed/head.S and some
other files in that directory are built with -march=all since kernel
commit 80cec14a "[ARM] Add -march=all to assembly file build in
arch/arm/boot/compressed" back in v2.6.28.

This patch reverts Russell's nice solution and instead marks the head.S
file to be built for armv7-a, which fortunately lets us build all
instructions in that file without warnings even on the broken binutils.

Without this patch, building anything results in:

arch/arm/boot/compressed/head.S: Assembler messages:
arch/arm/boot/compressed/head.S:565: Warning: (null)
arch/arm/boot/compressed/head.S:676: Warning: (null)
arch/arm/boot/compressed/head.S:698: Warning: (null)
arch/arm/boot/compressed/head.S:722: Warning: (null)
arch/arm/boot/compressed/head.S:726: Warning: (null)
arch/arm/boot/compressed/head.S:957: Warning: (null)
arch/arm/boot/compressed/head.S:996: Warning: (null)
arch/arm/boot/compressed/head.S:997: Warning: (null)
arch/arm/boot/compressed/head.S:1027: Warning: (null)
arch/arm/boot/compressed/head.S:1035: Warning: (null)
arch/arm/boot/compressed/head.S:1046: Warning: (null)
arch/arm/boot/compressed/head.S:1060: Warning: (null)
arch/arm/boot/compressed/head.S:1092: Warning: (null)
arch/arm/boot/compressed/head.S:1094: Warning: (null)
arch/arm/boot/compressed/head.S:1095: Warning: (null)
arch/arm/boot/compressed/head.S:1102: Warning: (null)
arch/arm/boot/compressed/head.S:1134: Warning: (null)
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: stable@vger.kernel.org
Cc: Matthew Gretton-Dann <matthew.gretton-dann@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The cpu_topology symbol is required by any driver using the topology
interfaces, which leads to a couple of build errors:

ERROR: "cpu_topology" [drivers/net/ethernet/sfc/sfc.ko] undefined!
ERROR: "cpu_topology" [drivers/cpufreq/arm_big_little.ko] undefined!
ERROR: "cpu_topology" [drivers/block/mtip32xx/mtip32xx.ko] undefined!

The obvious solution is to export this symbol.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NWill Deacon <will.deacon@arm.com>
Cc: stable@vger.kernel.org
Cc: Nicolas Pitre <nico@linaro.org>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Selecting this option produces:

  AS      arch/arm/boot/compressed/debug.o
arch/arm/boot/compressed/debug.S:4:33: fatal error: mach/debug-macro.S: No such file or directory
compilation terminated.
make[3]: *** [arch/arm/boot/compressed/debug.o] Error 1

The semihosting support cannot be modelled into a senduart macro as
it requires memory space for argument passing.  So the
CONFIG_DEBUG_LL_INCLUDE may not have any sensible value and the include
directive should be omitted.

While at it, let's add proper semihosting output support to the
decompressor.
Signed-off-by: NNicolas Pitre <nico@linaro.org>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Update the CMT clockevent rating from 125 to 80.

This resolves a boot-failure regression for kzm9g-reference in v3.10-rc1
introduced by f7db706b ("ARM: 7674/1: smp:
Avoid dummy clockevent being preferred over real").

The patch noted above reduces the rating of dummy clockevent from 400 to 100.
This patch reduces the rating of CMT so that it is once again less than that
of the dummy clockevent.
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

OMAP5 has 6 timers (GPTimers 5, 6, 8 to 11) that are capable of PWM.
The PWM capability property is missing from the node definitions of
couple of timers.

Add ti,timer-pwm attribute for timer 5, 6, 8 and 11.
Signed-off-by: NSuman Anna <s-anna@ti.com>
[benoit.cousson@linaro.org: Update changelog and subject to highlight
the fix]
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Earlier commits ensured proper muxing of pins related to proper
TWL6030 behavior: see commit 265a2bc8 (ARM: OMAP3: TWL4030: ensure
sys_nirq1 is mux'd and wakeup enabled) and commit 1ef43369 (ARM:
OMAP4: TWL: mux sys_drm_msecure as output for PMIC).

However these only fixed legacy boot and not DT boot.  For DT boot,
the default mux values need to be set properly in DT.

Special thanks to Nishanth Menon for the review and catching some
major flaws in earlier versions.

Tested on OMAP4430/Panda and OMAP4460/Panda-ES.

Cc: Nishanth Menon <nm@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NKevin Hilman <khilman@linaro.org>
Acked-by: NGrygorii Strashko <grygorii.strashko@ti.com>
[benoit.cousson@linaro.org: Slightly change the subject to align
board name with file name]
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

The gpmc driver is actually looking for "gpmc,num-cs" and
"gpmc,num-waitpins" properties in DT. The binding doc also states
this.
Correct the properties in the dts to provide the right values for the
gpmc driver.
Signed-off-by: NLars Poeschel <poeschel@lemonage.de>
Acked-by: NPeter Korsgaard <jacmet@sunsite.dk>
Acked-by: NPekon Gupta <pekon@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

The UART2 hwmod structure is pointing to the EDMA channels of UART1,
which doesn't look right. This patch fixes this by making the UART2
hwmod structure to a new structure that lists the EDMA channels to be
used by the UART2.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: NVaibhav Hiremath <hvaibhav@ti.com>
[paul@pwsan.com: updated to apply]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

The KVM/ARM MMU code doesn't take care of invalidating TLBs before
freeing a {pte,pmd} table. This could cause problems if the page
is reallocated and then speculated into by another CPU.
Reported-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NChristoffer Dall <cdall@cs.columbia.edu>

Some ARM KVM VCPU ioctls require the vCPU to be properly initialized
with the KVM_ARM_VCPU_INIT ioctl before being used with further
requests. KVM_RUN checks whether this initialization has been
done, but other ioctls do not.
Namely KVM_GET_REG_LIST will dereference an array with index -1
without initialization and thus leads to a kernel oops.
Fix this by adding checks before executing the ioctl handlers.

 [ Removed superflous comment from static function - Christoffer ]

Changes from v1:
 * moved check into a static function with a meaningful name
Signed-off-by: NAndre Przywara <andre.przywara@linaro.org>
Signed-off-by: NChristoffer Dall <cdall@cs.columbia.edu>

The AXI clock mux should be as below:

00: periph;
01: pll2_pfd2_396m;
10: periph;
11: pll3_pfd1_540m;
Signed-off-by: NAnson Huang <b20788@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Stephen Warren reported the recent commit 78506f22 (add support for
extended FIFO-size of PL011-r1p5) breaks the serial port on the
BCM2835 ARM SoC.

A UART compatible with the ARM PL011-r1p5 should have 32-deep FIFOs.
The BCM2835 UART just looks like an ARM PL011-r1p5, but has 16-deep
FIFOs just like PL011-r1p4 or earlier revisions. As a workaround for
this compatibility issue, this patch overrides the HW UART periphid
register values with the actually compatible UART periphid 0x00241011
(r1p3 or r1p4).
Reported-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NJongsung Kim <neidhard.kim@lge.com>
Signed-off-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Commit a819c4f1 (ARM: OMAP3: PM: Only access IVA if one exists)
changed PM to not access IVA registers on omaps that don't have
them. Turns out we still need to idle iva2 as otherwise
iva2_pwrdm will stay on and block deeper idle states.

It seems that the only part of the reset that may not be needed
is the setting of the iva2 boot mode to idle. But as that register
seems to be there and is harmless if no iva2 is on the SoC, it's
probably safest to do the complete reset.
Acked-by: NMark A. Greer <mgreer@animalcreek.com>
Acked-by: NKevin Hilman <khilman@linaro.org>
Tested-by: NYegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This turns on a number of configs that are useful on the Chromebook, but also
good to have on in general:

* USB host and MMC drivers(!)
* I2C GPIO arbitration driver
* CYAPA trackpad driver
* simplefb
* CROS EC and keyboard drivers
* S5M8767 driver
* MAX77686 drivers
* MAX8997 driver
* DEVTMPFS + mount
* DM_CRYPT (as module)
* CRYPTOLOOP
* HIGHMEM
* PRINTK timestamps

This also turns off DEBUG_LL, and switches the hardcoded Samsung lowlevel
uart to uart 3 (which is only used to show the "uncompressing kernel"
message at boot, it seems).
Signed-off-by: NOlof Johansson <olof@lixom.net>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Tested-by: NTushar Behera <tushar.behera@linaro.org>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>

When adding CPU to the SMP group and enabling the coherency on this
CPU we must protect the register access.
The previous implementation claims to be atomic but doesn't provide
any protection against parallel access to the coherency fabric control
and configuration registers.

This patch fixes this by using the ldrex and strex mechanism.
This method should be used in all accesses to those registers.

[gregory.clement@free-electrons.com: fixed the commit's topic]
Signed-off-by: NNadav Haklai <nadavh@marvell.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

When creating the DT based boards-ts219.c the none DT ts219-setup.c
was used as a template. This includes a lateinit() call to initialize
the PCIe bus. The code makes use of machine_is_ts219() which is never
true on DT, so a FIXME was added and the code left as is. This was
unproblematic until b73690c8: "ARM: Kirkwood: Support basic
hotplug for PCI-E" which changes the way the PCIe bus is
initialized. The non-DT ts219-setup.c now crashes during boot.  The
lateinit() call in the DT boards-ts219.c is being called,
machine_is_ts219() is true and so the PCIe is initialized a second
time.

This patch removes the useless, and now clearly dangerous, code from
boards-ts219.c, making ts219-setup.c work again.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Cc: <stable@vger.kernel.org> # v3.9.x
Signed-off-by: NJason Cooper <jason@lakedaemon.net>