Now that each NAPI instance has its own producer ring, it no longer
makes sense to keep the producer ring structure external.  This patch
migrates the producer ring struct to tg3_napi and pivots the code to the
new implementation.
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TG3_IRQ_MAX_VECS should be seen as the maximum number of vectors that
any device could be expected to use.  tp->irq_max represents the maximum
number of vectors the current device can use.  This patch clarifies the
semantics of the code to match the above description.
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adjusts the driver to use the tg3_start_xmit_dma_bug()
transmit routine for all revisions of 5717 asic rev devices and then
allows the driver to attach to B0 and later devices.
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NCSI firmware does not accept APE events.  It relies on a "driver state"
location in shared memory to tell it what the driver's current state is.

This patch pivots the code to use the new driver state scheme.
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It was recently discovered that enabling TSS can lockup the device.
This patch disables the feature until a suitable workaround can be
found.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Earlier versions of tg3 devices had a problem where the read DMA FIFO
could be overrun in certain edge conditions.  The fix was to limit the
number of rx BDs the hardware would fetch at a time.  For later devices
(5761, 5784 and later ASIC revs), there is a hardware fix that must be
enabled to fix the same problem.  This patch adds that hardware fix.

There is a gap in the ASIC revision lineage where neither fix is
applied.  This is intentional as these ASIC revisions are not afflicted
by the bug.
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fresh skbs have ip_summed set to CHECKSUM_NONE (0)

We can avoid setting again skb->ip_summed to CHECKSUM_NONE in drivers.

Introduce skb_checksum_none_assert() helper so that we keep this
assertion documented in driver sources.

Change most occurrences of :

skb->ip_summed = CHECKSUM_NONE;

by :

skb_checksum_none_assert(skb);
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates the tg3 version to 3.113.
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch moves most of the phy related flag definitions over to the
phyflags member and changes the code accordingly.
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch deletes the link_config.phy_is_low_power flag and creates a
new phy_flags device member to store all phy related settings.  All the
code is converted accordingly.
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch replaces some instances of hardcoded phy register values with
preprocessor equivalents.
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds error reporting to the tg3_phydsp_write() function and
converts a few more locations to use this function over the inlined
equivalent.
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

smp_mb() inside tg3_tx_avail() is used twice in the normal
tg3_start_xmit() path (see illustration below).  The full memory
barrier is only necessary during race conditions with tx completion.
We can speed up the tx path by replacing smp_mb() in tg3_tx_avail()
with a compiler barrier.  The compiler barrier is to force the
compiler to fetch the tx_prod and tx_cons from memory.

In the race condition between tg3_start_xmit() and tg3_tx(),
we have the following situation:

tg3_start_xmit()                       tg3_tx()
    if (!tg3_tx_avail())
        BUG();

    ...

    if (!tg3_tx_avail())
        netif_tx_stop_queue();         update_tx_index();
        smp_mb();                      smp_mb();
        if (tg3_tx_avail())            if (netif_tx_queue_stopped() &&
            netif_tx_wake_queue();         tg3_tx_avail())

With smp_mb() removed from tg3_tx_avail(), we need to add smp_mb() to
tg3_start_xmit() as shown above to properly order netif_tx_stop_queue()
and tg3_tx_avail() to check the ring index.  If it is not strictly
ordered, the tx queue can be stopped forever.

This improves performance by about 3% with 2 ports running
bi-directional 64-byte packets.
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These devices were never released to the public.
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds code to determine the APE firmware type and report this
along with the firmware version.
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ASPM workaround setting obtained from NVRAM only works with devices
older than 5717.  This patch enforces the restriction.
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes the code to only manage the PCIe gphy power for
CPMU-less devices only.  The CPMU takes over management for newer
chips.
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The phy test register location has been repurposed for 5717+ devices.
This patch changes the code to avoid this location for these devices.
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch creates a TG3_FLG3_5717_PLUS flag to collectively describe
the set of changes in the ASIC that will apply to all future chip
revisions.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The TSS flag needs to be turned off during tg3_close().  If the device
fails to allocate more than one MSI-X vector the next time the device is
brought up, transmits will fail.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tg3 commit e7126997 entitled
"tg3: Preserve PCIe MPS setting for new devs" attempted to ensure the
PCIe link negotiated Maximum Payload Size (MPS) setting was 128 bytes
for all devices that didn't support higher speeds.  The 5784 device was
mistakenly added to this list when it shouldn't have.  This patch
removes the 5784 ASIC rev devices from that list.
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The phy_mii_ioctl() function unnecessarily throws away the original ifreq.
We need access to the ifreq in order to support PHYs that can perform
hardware time stamping.

Two maverick drivers filter the ioctl commands passed to phy_mii_ioctl().
This is unnecessary since phylib will check the command in any case.
Signed-off-by: NRichard Cochran <richard.cochran@omicron.at>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates the tg3 version to 3.112.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the following checkpatch errors:

ERROR: do not use assignment in if condition
+	if ((mss = skb_shinfo(skb)->gso_size) != 0) {

ERROR: do not use assignment in if condition
+	if ((mss = skb_shinfo(skb)->gso_size) != 0) {

ERROR: space prohibited after that '!' (ctx:BxW)
+			if (! netif_carrier_ok(tp->dev) &&
 			    ^

ERROR: space required after that ',' (ctx:VxV)
+#define GET_REG32_LOOP(base,len)		\
                            ^

ERROR: "(foo*)" should be "(foo *)"
+		memcpy(data, ((char*)&val) + b_offset, b_count);

ERROR: do not use assignment in if condition
+		if ((err = tg3_do_mem_test(tp, mem_tbl[i].offset,
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch reverts commit 52cdf852,
entitled "tg3: Prevent a PCIe tx glitch".  The problem does not have
any visible side-effects and happens too early for the driver to do
anything about it.  The proper place for this code is within the
device's bootcode.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes the code so that the driver version can be reported
to the firmware in addition to the current use.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tg3 is coded to refuse to attach to 5717 serdes devices.  Now that the
hardware is better supported, we can relax this restriction.  This patch
also fixes a recently introduced bug which will cause serdes parallel
detection not to work with 5780 class devices.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The tg3_start_xmit_dma_bug() function was missing code to process IPv6
TSO packets.  This patch adds the missing support.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The interrupt coalescing setup code used the TG3_FLG2_USING_MSIX flag to
determine whether or not to configure the rx coalescing parameters.
This is incorrect for the single MSI-X vector case.  This patch changes
the code to look at the TG3_FLG3_ENABLE_RSS instead.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch reverts commit 2601d8a0.  A
spectacular set of coincidences made it look as though the table was
setup incorrectly.  The original version was correct.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Similar to commit 72dccb01 (bnx2: Update vlan_features)

In order to enable TSO on vlan devices, tg3 needs to update
dev->vlan_features.

Tested on HP NC326m (aka BCM5715S (rev a3))
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now core network is able to handle 64 bit netdevice stats on 32 bit
arches, we can provide them for tg3, since hardware maintains 64 bit
counters.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates the tg3 version to 3.111.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the 5719 PCI device and phy IDs.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the 5719 ASIC revision.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver sometimes needs to know which function number the current
device is.  This patch changes the code to use devfn over internal
register values.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 5717 serdes phy brings link up via parallel detection without any
additional help from the driver.  This patch changes the
tg3_setup_fiber_mii_phy() function to detect and allow the use of this
feature.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes the code to make it legal to allocate only one MSI-X
vector.  It also fixes a bug where the driver was not checking for error
return codes from pci_enable_msix().
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver was incorrectly programming the indirection table such that
rx traffic intended for the second ring went to the first ring, rx
traffic intended for the third ring went to the second ring, etc.  This
patch changes the code so that rx traffic is diverted to the proper
ring.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The rx resources for MSI-X interrupt vector 0 were not being freed
correctly.  This happens because the teardown loop continue's to the
next loop iteration if it detects the tx ring for that vector is not
setup, thus bypassing the rx teardown code.  This patch moves the
call to tg3_rx_prodring_free() earlier in the loop.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>