Replace an unnecessary subtraction with a bitwise AND when determining the
value of ext_tcode in fw_fill_transaction() to save a cpu cycle or two in a
somewhat critical path.
Signed-off-by: NJarod Wilson <jwilson@redhat.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

read_rom() obtained a fresh new fw_device.generation for each read
transaction.  Hence it was able to continue reading in the middle of the
ROM even if a bus reset happened.  However the device may have modified
the ROM during the reset.  We would end up with a corrupt fetched ROM
image then.

Although all of this is quite unlikely, it is not impossible.
Therefore we now restart reading the ROM if the bus generation changed.

Note, the memory barrier in read_rom() is still necessary according to
tests by Jarod Wilson, despite of the ->generation access being moved up
in the call chain.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

This is essentially what I've been beating on locally, and I've yet to hit
another config rom read failure with it.
Signed-off-by: NJarod Wilson <jwilson@redhat.com>

fw_device.node_id and fw_device.generation are accessed without mutexes.
We have to ensure that all readers will get to see node_id updates
before generation updates.

Fixes an inability to recognize devices after "giving up on config rom",
https://bugzilla.redhat.com/show_bug.cgi?id=429950Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Reviewed by Nick Piggin <nickpiggin@yahoo.com.au>.

Verified to fix 'giving up on config rom' issues on multiple system and
drive combinations that were previously affected.
Signed-off-by: NJarod Wilson <jwilson@redhat.com>
Signed-off-by: NKristian Høgsberg <krh@redhat.com>

We have to use the fw_device.generation here, not the fw_card.generation,
because the generation must never be newer than the node ID when we emit
a transaction.  This cannot be guaranteed with fw_card.generation.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Verified in concert with subsequent memory barriers patch to fix 'giving
up on config rom' issues on multiple system and drive combinations that
were previously affected.
Signed-off-by: NJarod Wilson <jwilson@redhat.com>

There was a small window where a login or reconnect job could use an
already updated card generation with an outdated node ID.  We have to
use the fw_device.generation here, not the fw_card.generation, because
the generation must never be newer than the node ID when we emit a
transaction.  This cannot be guaranteed with fw_card.generation.

Furthermore, the target's and initiator's node IDs can be obtained from
fw_device and fw_card.  Dereferencing their underlying topology objects
is not necessary.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Verified in concert with subsequent memory barriers patch to fix 'giving
up on config rom' issues on multiple system and drive combinations that
were previously affected.
Signed-off-by: NJarod Wilson <jwilson@redhat.com>

Ask the target to grant 4 seconds instead of the standard and minimum of
1 second window after bus reset for reconnection.  This accelerates
reconnection if there are more than one targets on the bus:  If a login
and inquiry to one target blocks the fw-sbp2 workqueue for more than 1s
after bus reset, we now still can reconnect to the other target.

Before that, fw-sbp2's reconnect attempts would be rejected with "error
status: 0:9" (function rejected), and fw-sbp2 would finally re-login.
All those futile reconnect attemps cost extra time until the target
which needs re-login is ready for I/O again.

The reconnect timeout field in the login ORB doesn't have to be honored
by the target though.  I found that we could get up to
  - allegedly 32768s from an old OXFW911 firmware
  - 256s from LSI bridges
  - 4s from OXUF922 and OXFW912 bridges,
  - 2s from TI bridges,
  - only the standard 1s from Initio and Prolific bridges and from
    Apple OpenFirmware in target mode.

We just try to get 4 seconds which already covers the case of a few
HDDs on the same bus quite nicely.

A minor drawback occurs in the following (rare and impractical) border
case:
  - two initiators are there, initiator 1 holds an exclusive login to
    a target,
  - initiator 1 goes off the bus,
  - target refuses login attempts from initiator 2 until reconnect_hold
    seconds after bus reset.

An alternative approach to the issue at hand would be to parallelize
fw-sbp2's reconnect and login work.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: NJarod Wilson <jwilson@redhat.com>

Don't attempt to send a logout ORB if the target was already unplugged
or had its link switched off.  If two targets are attached, this
enhances the chance to quickly reconnect to the remaining target when
one target is plugged out.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: NJarod Wilson <jwilson@redhat.com>

Previously, the fw-ohci driver used fixed-length buffers for storing
descriptors for isochronous receive DMA programs.  If an application
(such as libdc1394) generated a DMA program that was too large, fw-ohci
would reach the limit of its fixed-sized buffer and return an error to
userspace.

This patch replaces the fixed-length ring-buffer with a linked-list of
page-sized buffers.  Additional buffers can be dynamically allocated and
appended to the list when necessary.  For a particular context, buffers
are kept around after use and reused as necessary, so there is no
allocation taking place after the DMA program is generated for the first
time.

In addition, the buffers it uses are coherent for DMA so there is no
syncing required before and after writes.  This syncing wasn't properly
done in the previous version of the code.

-

This is the fourth version of my patch that replaces a fixed-length
buffer for DMA descriptors with a dynamically allocated linked-list of
buffers.

As we discovered with the last attempt, new context programs are
sometimes queued from interrupt context, making it unacceptable to call
tasklet_disable() from context_get_descriptors().

This version of the patch uses ohci->lock for all locking needs instead
of tasklet_disable/enable.  There is a new requirement that
context_get_descriptors() be called while holding ohci->lock.  It was
already held for the AT context, so adding the requirement for the iso
context did not seem particularly onerous.  In addition, this has the
side benefit of allowing iso queue to be safely called from concurrent
user-space threads, which previously was not safe.
Signed-off-by: NDavid Moore <dcm@acm.org>
Signed-off-by: NKristian Høgsberg <krh@redhat.com>
Signed-off-by: NJarod Wilson <jwilson@redhat.com>

-

Fixes the following issues:
  - Isochronous reception stopped prematurely if an application used a
    larger buffer.  (Reproduced with coriander.)
  - Isochronous reception stopped after one or a few frames on VT630x
    in OHCI 1.0 mode.  (Fixes reception in coriander, but dvgrab still
    doesn't work with these chips.)

Patch update: struct member alignment, whitespace nits
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

The firewire-ohci driver so far lacked the ability to resume cycle
master duty after that condition happened, as added to ohci1394 in Linux
2.6.18 by commit 57fdb58f.  This ports
this patch to fw-ohci.

The "cycle too long" condition has been seen in practice
  - with IIDC cameras if a mode with packets too large for a speed is
    chosen,
  - sporadically when capturing DV on a VIA VT6306 card with ohci1394/
    ieee1394/ raw1394/ dvgrab 2.
    https://bugzilla.redhat.com/show_bug.cgi?id=415841#c7
(This does not fix Fedora bug 415841.)
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Fix extraction of the source node id from the packet header.
Signed-off-by: NRabin Vincent <rabin@rab.in>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

This patch corrects a number of bugs in the current OHCI 1.0
packet-per-buffer support:

1. Correctly deal with payloads that cross a page boundary.  The
previous version would not split the descriptor at such a boundary,
potentially corrupting unrelated memory.

2. Allow user-space to specify multiple packets per struct
fw_cdev_iso_packet in the same way that dual-buffer allows.  This is
signaled by header_length being a multiple of header_size.  This
multiple determines the number of packets.  The payload size allocated
per packet is determined by dividing the total payload size by the
number of packets.

3. Make sync support work properly for packet-per-buffer.

I have tested this patch with libdc1394 by forcing my OHCI 1.1
controller to use the packet-per-buffer support instead of dual-buffer.

I would greatly appreciate testing by those who have a DV devices and
other types of iso streamers to make sure I didn't cause any
regressions.

Stefan, with this patch, I'm hoping that libdc1394 will work with all
your OHCI 1.0 controllers now.

The one bit of future work that remains for packet-per-buffer support is
the automatic compaction of short payloads that I discussed with
Kristian.
Signed-off-by: NDavid Moore <dcm@acm.org>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

This patch fixes the problem where different OHCI 1.1 controllers behave
differently when a received iso packet straddles three or more buffers
when using the dual-buffer receive mode.  Two changes are made in order
to handle this situation:

1. The packet sync DMA descriptor is given a non-zero header length and
non-zero payload length.  This is because zero-payload descriptors are
not discussed in the OHCI 1.1 specs and their behavior is thus
undefined.  Instead we use a header size just large enough for a single
header and a payload length of 4 bytes for this first descriptor.

2. As we process received packets in the context's tasklet, read the
packet length out of the headers.  Keep track of the running total of
the packet length as "excess_bytes", so we can ignore any descriptors
where no packet starts or ends.  These descriptors may not have had
their first_res_count or second_res_count fields updated by the
controller so we cannot rely on those values.

The main drawback of this patch is that the excess_bytes value might get
"out of sync" with the packet descriptors if something strange happens
to the DMA program.  I'm not if such a thing could ever happen, but I
appreciate any suggestions in making it more robust.

Also, the packet-per-buffer support may need a similar fix to deal with
issue 1, but I haven't done any work on that yet.

Stefan, I'm hoping that with this patch, all your OHCI 1.1 controllers
will work properly with an unmodified version of libdc1394.
Signed-off-by: NDavid Moore <dcm@acm.org>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

SBP2_MAX_SECTORS is nowhere used in fw-sbp2.
It merely got copied over from sbp2 where it played a role in the past.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

This somewhat reduces the size of firewire-sbp2.ko.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Bug noted by Pieter Palmers:  Isochronous transmit tasklets were
scheduled on isochronous receive events, in addition to the proper
isochronous receive tasklets.

http://marc.info/?l=linux1394-devel&m=119783196222802Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

This patch speeds up sbp2 a little bit --- but more importantly, it
brings the behavior of sbp2 and fw-sbp2 closer to each other.  Like
fw-sbp2, sbp2 now does not limit the size of single transfers to 255
sectors anymore, unless told so by a blacklist flag or by module load
parameters.

Only very old bridge chips have been known to need the 255 sectors
limit, and we have got one such chip in our hardwired blacklist.  There
certainly is a danger that more bridges need that limit; but I prefer to
have this issue present in both fw-sbp2 and sbp2 rather than just one of
them.

An OXUF922 with 400GB 7200RPM disk on an S400 controller is sped up by
this patch from 22.9 to 23.5 MB/s according to hdparm.  The same effect
could be achieved before by setting a higher max_sectors module
parameter.  On buses which use 1394b beta mode, sbp2 and fw-sbp2 will
now achieve virtually the same bandwidth.  Fw-sbp2 only remains faster
on 1394a buses due to fw-core's gap count optimization.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

The code has been in "#if 0 - #endif" since Linux 2.6.12.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Convert ieee1394 from nopage to fault.
Remove redundant vma range checks (correct resource range check is retained).
Signed-off-by: NNick Piggin <npiggin@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Replace sg->length by sg_dma_len(sg).  Rename a variable for shorter
line lengths and eliminate some superfluous local variables.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Both the old e1000 driver and the new e1000e driver can drive some
PCI-Express e1000 cards, and we should avoid ambiguity about which
driver will pick up the support for those cards when both drivers are
enabled.

This solves the problem by having the old driver support those cards if
the new driver isn't configured, but otherwise ceding support for PCI
Express versions of the e1000 chipset to the newer driver.  Thus
allowing both legacy configurations where only the old driver is active
(and handles all chips it knows about) and the new configuration with
the new driver handling the more modern PCIE variants.
Acked-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch adds a new configuration option, which adds support for a new
early_param which gets checked in arch/x86/kernel/setup_{32,64}.c:setup_arch()
to decide wether OHCI-1394 FireWire controllers should be initialized and
enabled for physical DMA access to allow remote debugging of early problems
like issues ACPI or other subsystems which are executed very early.

If the config option is not enabled, no code is changed, and if the boot
paramenter is not given, no new code is executed, and independent of that,
all new code is freed after boot, so the config option can be even enabled
in standard, non-debug kernels.

With specialized tools, it is then possible to get debugging information
from machines which have no serial ports (notebooks) such as the printk
buffer contents, or any data which can be referenced from global pointers,
if it is stored below the 4GB limit and even memory dumps of of the physical
RAM region below the 4GB limit can be taken without any cooperation from the
CPU of the host, so the machine can be crashed early, it does not matter.

In the extreme, even kernel debuggers can be accessed in this way. I wrote
a small kgdb module and an accompanying gdb stub for FireWire which allows
to gdb to talk to kgdb using remote remory reads and writes over FireWire.

An version of the gdb stub fore FireWire is able to read all global data
from a system which is running a a normal kernel without any kernel debugger,
without any interruption or support of the system's CPU. That way, e.g. the
task struct and so on can be read and even manipulated when the physical DMA
access is granted.

A HOWTO is included in this patch, in Documentation/debugging-via-ohci1394.txt
and I've put a copy online at
ftp://ftp.suse.de/private/bk/firewire/docs/debugging-via-ohci1394.txt

It also has links to all the tools which are available to make use of it
another copy of it is online at:
ftp://ftp.suse.de/private/bk/firewire/kernel/ohci1394_dma_early-v2.diffSigned-Off-By: NBernhard Kaindl <bk@suse.de>
Tested-By: NThomas Renninger <trenn@suse.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

The set_memory_* and set_pages_* family of API's currently requires the
callers to do a global tlb flush after the function call; forgetting this is
a very nasty deathtrap. This patch moves the global tlb flush into
each of the callers
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

This patch converts various users of change_page_attr() to the new,
more intent driven set_page_*/set_memory_* API set.
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

The function __cpufreq_set_policy in file drivers/cpufreq/cpufreq.c
has a very obvious error:

        if (policy->min > data->min && policy->min > policy->max) {
                ret = -EINVAL;
                goto error_out;
        }

This condtion statement is wrong because it returns -EINVAL only if
policy->min is greater than policy->max (in this case,
"policy->min > data->min" is true for ever.). In fact, it should
return -EINVAL as well if policy->max is less than data->min.

The correct condition should be:

	if (policy->min > data->max || policy->max < data->min) {

The following test result testifies the above conclusion:

Before applying this patch:

[root@yangyi-dev /]# cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_available_frequencies
2394000 1596000
[root@yangyi-dev /]# echo 1596000 > /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
[root@yangyi-dev /]# cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
1596000
[root@yangyi-dev /]# cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_min_freq
1596000
[root@yangyi-dev /]# echo "2000000" > /sys/devices/system/cpu/cpu0/cpufreq/scaling_min_freq
-bash: echo: write error: Invalid argument
[root@yangyi-dev /]# cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_min_freq
1596000
[root@yangyi-dev /]# echo "0" > /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
[root@yangyi-dev /]# cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
1596000
[root@yangyi-dev /]# echo "1595000" > /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
[root@yangyi-dev /]# cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
1596000
[root@yangyi-dev /]#

After applying this patch:

[root@yangyi-dev /]# cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_available_frequencies
2394000 1596000
[root@yangyi-dev /]# echo 1596000 > /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
[root@yangyi-dev /]# cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
1596000
[root@yangyi-dev /]# cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_min_freq
1596000
[root@localhost /]# echo "2000000" > /sys/devices/system/cpu/cpu0/cpufreq/scaling_min_freq
-bash: echo: write error: Invalid argument
[root@localhost /]# cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_min_freq
1596000
[root@localhost /]# echo "0" > /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
-bash: echo: write error: Invalid argument
[root@localhost /]# echo "1595000" > /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
-bash: echo: write error: Invalid argument
[root@localhost /]# cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
1596000
[root@localhost /]# echo "1596000" > /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
[root@localhost /]# echo "2394000" > /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
[root@localhost /]# cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
2394000
[root@localhost /]
Signed-off-by: NYi Yang <yi.y.yang@intel.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Signed-off-by: NYinghai Lu <yinghai@sun.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

the previous patch in the old RTC driver.  It also removes the direct
rtc_interrupt() call from arch/x86/kernel/hpetc.c so that there's finally no
(code) dependency to CONFIG_RTC in arch/x86/kernel/hpet.c.

Because of this, it's possible to compile the drivers/char/rtc.ko driver as
module and still use the HPET emulation functionality.  This is also expressed
in Kconfig.
Signed-off-by: NBernhard Walle <bwalle@suse.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: Andi Kleen <ak@suse.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Robert Picco <Robert.Picco@hp.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

The ACPI code currently disables TSC use in any C2 and C3
states. But the AMD Fam10h BKDG documents that the TSC
will never stop in any C states when the CONSTANT_TSC bit is
set. Make this disabling conditional on CONSTANT_TSC
not set on AMD.

I actually think this is true on Intel too for C2 states
on CPUs with p-state invariant TSC, but this needs
further discussions with Len to really confirm :-)

So far it is only enabled on AMD.

Cc: lenb@kernel.org
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

drivers/pnp/pnpbios/bioscalls.c:64: warning: (near initialization for 'bad_bios_desc.<anonymous>')
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Aviod TLB flush IPIs during C3 states by voluntary leave_mm()
before entering C3.

The performance impact of TLB flush on C3 should not be significant with
respect to C3 wakeup latency. Also, CPUs tend to flush TLB in hardware while in
C3 anyways.

On a 8 logical CPU system, running make -j2, the number of tlbflush IPIs goes
down from 40 per second to ~ 0. Total number of interrupts during the run
of this workload was ~1200 per second, which makes it ~3% savings in wakeups.

There was no measurable performance or power impact however.

[ akpm@linux-foundation.org: symbol export fixes. ]
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

People with HP Desktops (including me) encounter couple of DMI errors
during boot - dmi_save_oem_strings_devices: out of memory and
dmi_string: out of memory.

On some HP desktops the DMI data include OEM strings (type 11) out of
which only few are meaningful and most other are empty. DMI code
religiously creates copies of these 27 strings (65 bytes each in my
case) and goes OOM in dmi_string().

If DMI_MAX_DATA is bumped up a little then it goes and fails in
dmi_save_oem_strings while allocating dmi_devices of sizeof(struct
dmi_device) corresponding to these strings.

On x86_64 since we cannot use alloc_bootmem this early, the code uses a
static array of 2048 bytes (DMI_MAX_DATA) for allocating the memory DMI
needs. It does not survive the creation of empty strings and devices.

Fix this by detecting and not newly allocating empty strings and instead
using a one statically defined dmi_empty_string.

Also do not create a new struct dmi_device for each empty string - use
one statically define dmi_device with .name=dmi_empty_string and add
that to the dmi_devices list.

On x64 this should stop the OOM with same current size of DMI_MAX_DATA
and on x86 this should save a good amount of (27*65 bytes +
27*sizeof(struct dmi_device) bootmem.

Compile and boot tested on both 32-bit and 64-bit x86.
Signed-off-by: NParag Warudkar <parag.warudkar@gmail.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

There's no need for the *_MASK flags (TF_MASK, IF_MASK, etc), found in
processor.h (both _32 and _64). They have a one-to-one mapping with the
EFLAGS value. This patch removes the definitions, and use the already
existent X86_EFLAGS_ version when applicable.

[ roland@redhat.com: KVM build fixes. ]
Signed-off-by: NGlauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

replace outb_p() with udelay(2). This is a real ISA device so it likely
needs this particular delay.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

This patch unifies struct desc_ptr between i386 and x86_64.
They can be expressed in the exact same way in C code, only
having to change the name of one of them. As Xgt_desc_struct
is ugly and big, this is the one that goes away.

There's also a padding field in i386, but it is not really
needed in the C structure definition.
Signed-off-by: NGlauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

tons of style cleanup in drivers/char/rtc.c - no code changed:

   text    data     bss     dec     hex filename
   6400     384      32    6816    1aa0 rtc.o.before
   6400     384      32    6816    1aa0 rtc.o.after

since we seem to have a number of open breakages in this code we might
as well start with making the code more readable and maintainable.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>