After running this bonding setup script
    modprobe bonding miimon=100 mode=0 max_bonds=1
    ifconfig bond0 10.1.1.1/16
    ifenslave bond0 eth1
    ifenslave bond0 eth3
on s390 with qeth-driven slaves, modprobe -r fails with this message
    unregister_netdevice: waiting for bond0 to become free. Usage count = 1
due to twice detection of duplicate address.
Problem is caused by a missing decrease of ifp->refcnt in addrconf_dad_failure.
An extra call of in6_ifa_put(ifp) solves it.
Problem has been introduced with commit f2344a13.
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a bug in the interaction between ipv6_create_tempaddr and
addrconf_verify.  Because ipv6_create_tempaddr uses the cstamp and tstamp
from the public address in creating a private address, if we have not
received a router advertisement in a while, tstamp + temp_valid_lft might be
< now.  If this happens, the new address is created inside
ipv6_create_tempaddr, then the loop within addrconf_verify starts again and
the address is immediately deleted.  We are left with no temporary addresses
on the interface, and no more will be created until the public IP address is
updated.  To avoid this, set the expiry time to be the minimum of the time
left on the public address or the config option PLUS the current age of the
public interface.
Signed-off-by: NGlenn Wurster <gwurster@scs.carleton.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If privacy extentions are enabled, but no current temporary address exists,
then create one when we get a router advertisement.
Signed-off-by: NGlenn Wurster <gwurster@scs.carleton.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Another exported symbol only used in one file
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clean up a missing exit path in the ipv6 module init routines.  In
addrconf_init we call ipv6_addr_label_init which calls register_pernet_subsys
for the ipv6_addr_label_ops structure.  But if module loading fails, or if the
ipv6 module is removed, there is no corresponding unregister_pernet_subsys call,
which leaves a now-bogus address on the pernet_list, leading to oopses in
subsequent registrations.  This patch cleans up both the failed load path and
the unload path.  Tested by myself with good results.
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>

 include/net/addrconf.h |    1 +
 net/ipv6/addrconf.c    |   11 ++++++++---
 net/ipv6/addrlabel.c   |    5 +++++
 3 files changed, 14 insertions(+), 3 deletions(-)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change "return (EXPR);" to "return EXPR;"

return is not a function, parentheses are not required.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Similar to accepting router advertisement, the IPv6 stack does not send router
solicitations if forwarding is enabled.

This patch enables this behavior to be overruled by setting forwarding to the
special value 2.
Signed-off-by: NThomas Graf <tgraf@infradead.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the interface has IPv6 disabled, don't add a multicast or
link-local route since we won't be adding a link-local address.
Reported-by: NMahesh Kelkar <maheshkelkar@gmail.com>
Signed-off-by: NBrian Haley <brian.haley@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

/proc/net/snmp and /proc/net/netstat expose SNMP counters.

Width of these counters is either 32 or 64 bits, depending on the size
of "unsigned long" in kernel.

This means user program parsing these files must already be prepared to
deal with 64bit values, regardless of user program being 32 or 64 bit.

This patch introduces 64bit snmp values for IPSTAT mib, where some
counters can wrap pretty fast if they are 32bit wide.

# netstat -s|egrep "InOctets|OutOctets"
    InOctets: 244068329096
    OutOctets: 244069348848
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

max_desync_factor can be configured per-interface, but nothing is
using the value.
Reported-by: NPiotr Lewandowski <piotr.lewandowski@gmail.com>
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since addresses are only revalidated every 2 minutes, the reported
valid_lft can underflow shortly before the address is deleted.
Clamp it to a minimum of 0, as for prefered_lft.
Reported-by: NPiotr Lewandowski <piotr.lewandowski@gmail.com>
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for 64bit snmp counters for some mibs,
add an 'align' parameter to snmp_mib_init(), instead
of assuming mibs only contain 'unsigned long' fields.

Callers can use __alignof__(type) to provide correct
alignment.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
CC: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

remove useless union keyword in rtable, rt6_info and dn_route.

Since there is only one member in a union, the union keyword isn't useful.
Signed-off-by: NChangli Gao <xiaosuo@gmail.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch ensures that all places that schedule the DAD timer
look at the address state in a safe manner before scheduling the
timer.  This ensures that we don't end up with pending timers
after deleting an address.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch makes use of the new POSTDAD state.  This prevents
a race between DAD completion and failure.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch makes use of the new state_lock to synchronise between
updates to the ifa state.  This fixes the issue where a remotely
triggered address deletion (through DAD failure) coincides with a
local administrative address deletion, causing certain actions to
be performed twice incorrectly.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch replaces the boolean dead flag on inet6_ifaddr with
a state enum.  This allows us to roll back changes when deleting
an address according to whether DAD has completed or not.

This patch only adds the state field and does not change the logic.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The duplicate address check code got broken in the conversion
to hlist (2.6.35).  The earlier patch did not fix the case where
two addresses match same hash value. Use two exit paths,
rather than depending on state of loop variables (from macro).

Based on earlier fix by Shan Wei.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Reviewed-by: NShan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add hlist_for_each_entry_rcu_bh() and
hlist_for_each_entry_continue_rcu_bh() macros, and use them in
ipv6_get_ifaddr(), if6_get_first() and if6_get_next() to fix lockdeps
warnings.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: N"Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sparse can help us find endianness bugs, but we need to make some
cleanups to be able to more easily spot real bugs.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The notifier for address down should only be called if address is completely
gone, not just being marked as tentative on link transistion. The code
in net-next would case bonding/sctp/s390 to see address disappear on link
down, but they would never see it reappear on link up.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since an address in hash list has to already have a ref count,
no additional ref count is needed.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When link goes down, want address to be preserved but in a tentative
state, therefore it has to stay in hash list.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Recent changes preserve IPv6 address when link goes down (good).
But would cause address to point to dead dst entry (bad).
The simplest fix is to just not delete route if address is
being held for later use.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h

percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: NTejun Heo <tj@kernel.org>
Guess-its-ok-by: NChristoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>

When a dump is interrupted at the last device in a hash chain and
then continued, "idx" won't get incremented past s_idx, so s_ip_idx
is not reset when moving on to the next device. This means of all
following devices only the last n - s_ip_idx addresses are dumped.
Tested-by: NPawel Staszewski <pstaszewski@itcare.pl>
Signed-off-by: NPatrick McHardy <kaber@trash.net>

Finishing naturally from hlist_for_each_entry(x, ...) does not result
in 'x' being NULL.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use list_add_tail() to get the behavior we had before
the list_head conversion for ipv6 address lists.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

hlist_for_each_entry(p...) will not necessarily initialize 'p'
to anything if the hlist is empty.  GCC notices this and emits
a warning.

Just return true explicitly when we hit a match, and return
false is we fall out of the loop without one.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch reduces timer events while keeping accuracy by rounding
our timer and/or batching several address validations in addrconf_verify().

addrconf_verify() is called at earliest timeout among interface addresses'
timeouts, but at maximum ADDR_CHECK_FREQUENCY (120 secs).

In most cases, all of timeouts of interface addresses are long enough
(e.g. several hours or days vs 2 minutes), this timer is usually called
every ADDR_CHECK_FREQUENCY, and it is okay to be lazy.
(Note this timer could be eliminated if all code paths which modifies
variables related to timeouts call us manually, but it is another story.)

However, in other least but important cases, we try keeping accuracy.

When the real interface address timeout is coming, and the timeout
is just before the rounded timeout, we accept some error.

When a timeout has been reached, we also try batching other several
events in very near future.
Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The variable regen_advance is only used in the privacy case.
Move it to simplify code and eliminate ifdef's
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix some of the checkpatch complaints.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some minor stuff, reformat comments and add whitespace for clarity
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert to list macro's for the list of addresses per interface
in IPv6.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The existing hash function has a couple of issues:
  * it is hardwired to 16 for IN6_ADDR_HSIZE
  * limited to 256 and callers using int
  * use jhash2 rather than some old BSD algorithm

No need for random seed since this is local only (based on assigned
addresses) table.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert from reader/writer lock to RCU and spinlock for addrconf
hash list.

Adds an additional helper macro for hlist_for_each_entry_continue_rcu
to handle the continue case.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using hash list macros, simplifies code and helps later RCU.

This patch includes some initialization that is not strictly necessary,
since an empty hlist node/list is all zero; and list is in BSS
and node is allocated with kzalloc.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use list macros instead of open coded linked list.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since generally there could be more netdevices changing type other
than bonding, making this event type name "bonding-unrelated"
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If we are managing IPv6 addresses using DHCP, it would be nice
for user-space to be notified if an address configured through
DHCP fails DAD.  Otherwise user-space would have to poll to see
whether DAD succeeds.

This patch uses the existing notification mechanism and simply
hooks it into the DAD failure code path.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>