msm_serial_driver is registered using platform_driver_probe which takes
care for the probe function itself.  So don't pass it in the driver
struct, too.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 5fd29d6c ("printk: clean up
handling of log-levels and newlines") changed printk semantics.  printk
lines with multiple KERN_<level> prefixes are no longer emitted as
before the patch.

<level> is now included in the output on each additional use.

Remove all uses of multiple KERN_<level>s in formats.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix up the error bit handling on SCI ports.
Signed-off-by: NSUGIOKA Toshinobu <sugioka@itonet.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NYoichi Yuasa <yuasa@linux-mips.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch updates the receive error code for muxed
interrupts in the sh-sci driver.

Receive error interrupts may be generated by the hardware
if RE or REIE bits in SCSCR are set. Update the muxed
interrupt handling code to acknowledge error interrupts
if RE or REIE is set, instead of only acknowledging if
REIE is set.

Without this patch error interrupts may be generated but
never acked resulting in a "nobody cared" crash.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add support for the PCI-Express NetMos 9901 Multi-IO card.

0001:06:00.0 Serial controller [0700]: NetMos Technology Device [9710:9901] (prog-if 02 [16550])
        Subsystem: Device [a000:1000]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 65
        Region 0: I/O ports at 0030 [size=8]
        Region 1: Memory at 80105000 (32-bit, non-prefetchable) [size=4K]
        Region 4: Memory at 80104000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: <access denied>
        Kernel driver in use: serial
        Kernel modules: 8250_pci

0001:06:00.1 Serial controller [0700]: NetMos Technology Device [9710:9901] (prog-if 02 [16550])
        Subsystem: Device [a000:1000]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin B routed to IRQ 65
        Region 0: I/O ports at 0020 [size=8]
        Region 1: Memory at 80103000 (32-bit, non-prefetchable) [size=4K]
        Region 4: Memory at 80102000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: <access denied>
        Kernel driver in use: serial
        Kernel modules: 8250_pci

0001:06:00.2 Parallel controller [0701]: NetMos Technology Device [9710:9901] (prog-if 03 [IEEE1284])
        Subsystem: Device [a000:2000]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin C routed to IRQ 65
        Region 0: I/O ports at 0010 [size=8]
        Region 1: I/O ports at <unassigned>
        Region 2: Memory at 80101000 (32-bit, non-prefetchable) [size=4K]
        Region 4: Memory at 80100000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: <access denied>
        Kernel driver in use: parport_pc
        Kernel modules: parport_pc

[   16.760181] PCI parallel port detected: 416c:0100, I/O at 0x812010(0x0), IRQ 65
[   16.760225] parport0: PC-style at 0x812010, irq 65 [PCSPP,TRISTATE,EPP]
[   16.851842] serial 0001:06:00.0: enabling device (0004 -> 0007)
[   16.883776] 0001:06:00.0: ttyS0 at I/O 0x812030 (irq = 65) is a ST16650V2
[   16.893832] serial 0001:06:00.1: enabling device (0004 -> 0007)
[   16.926537] 0001:06:00.1: ttyS1 at I/O 0x812020 (irq = 65) is a ST16650V2
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use the newly introduced pci_ioremap_bar() function in drivers/serial.
pci_ioremap_bar() just takes a pci device and a bar number, with the goal
of making it really hard to get wrong, while also having a central place
to stick sanity checks.
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove unneeded casts.
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Implement the serial polling hooks for the serial_txx9 uart for use with
kgdboc.

This patch once got SOB from Jason on Jul 2008 and (perhaps) merged into
kgdb-next branch, but lost somewhere then.  I resend it now with Jason's
Acked-by.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: NJason Wessel <jason.wessel@windriver.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The tty layer is now a bit more fussy about reporting the right baud rate
back. Make the msm driver match the current state of affairs.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NBrian Swetland <swetland@google.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Hardware updated to support TX FIFO empty.
Signed-off-by: NRichard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Mark the remove function as __devexit so it gets eliminated in
CONFIG_HOTPLUG=n builds.  Saves ~100 bytes.
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Acked-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In zs_console_putchar() occurs:

	if (zs_transmit_drain(zport, irq))
		write_zsdata(zport, ch);

However if in zs_transmit_drain() no empty Tx Buffer occurs, limit reaches
-1 => true, and the write still occurs.

This patch changes postfix to prefix decrements in this and similar
functions to prevent similar mistakes in the future.  This decreases the
iterations with one but the chosen loop count was arbitrary anyway.

In sunhv limit reaches -1, not 0, so the test is off by one.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NMaciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Since early printk only makes sense/works when the serial driver is built
into the kernel, disable the option for this driver when it is going to be
built as a module.  Otherwise we get build failures due to the ifdef
handling.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The Blackfin serial driver never initialized the spin_lock that is part of
the serial core structure, but we never noticed because spin_lock's are
rarely enabled on UP systems.  Yeah lockdep and friends.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

So far, MPC512x used mpc512x_find_ips_freq() to get the bus frequency,
while MPC52xx used mpc52xx_find_ipb_freq().  Despite the different
clock names (IPS vs. IPB) the code was identical.

Use common code for both processor families.
Signed-off-by: NWolfgang Denk <wd@denx.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

After enabling hardware flow control, any subsequent termios call may hang
waiting for the transmitter to drain.  This appears to be caused by a
busy-loop in set_termios() waiting for the transmitter to become empty,
which may take a very long time (or hang indefinitely) if the device at
the other end is blocking us.

A quick look through the tty and serial_core code indicates that any
necessary flushing (which is optional) has already been done at this
point, so there's no need for the driver to flush the transmitter on its
own.

Fix it by removing the busy-loop altogether.
Tested-by: NEirik Aanonsen <eaa@wprmedical.com>
Signed-off-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device.  Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used.  These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NStephen Rothwell <sfr@canb.auug.org.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Matthias Fuchs <mfuchs@ma-fu.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds the UPF_FIXED_TYPE flag which will bypass the
8250's autoconfig probe for uart type. The uart type identified
by the of_serial's parse of the flat device tree will be utilized
as defined.
Signed-off-by: NDave Mitchell <dmitchell@amcc.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

In HW UART mode the TxBD[READY] is not cleared by H/W (RISC engine) when
the user send characters to Tx buffer of QE UART.  So, these characters
stay on the QE forever, never go to UART line.
Signed-off-by: NDave Liu <daveliu@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Presently the boot log whines about suspend/resume hooks at the platform
driver level, move these over to dev_pm_ops.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

.ko is normally not included in Kconfig help, make it consistent.
Signed-off-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

real baud rate may be different from the one requested.
for upper layers, set the nearest value to the real rate
in favour of the rate previously requested.
Signed-off-by: NOskar Schirmer <os@emlix.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Using the iMX serial driver with an IrDA device
needs extra peripheral settings and specific
timing depending on the transmitter circuitry used.
Signed-off-by: NFabian Godehardt <fg@emlix.com>
Signed-off-by: NOskar Schirmer <os@emlix.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

for calculation of numerator and denominator
used in baud rate setting, use generic library function
for optimum settings.
Signed-off-by: NOskar Schirmer <os@emlix.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

correctly de-initialise device when setting up failed,
call to pdata->exit() was missing.
Signed-off-by: NDaniel Glöckner <dg@emlix.com>
Signed-off-by: NOskar Schirmer <os@emlix.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

needed to avoid continued transmission by hardware
while software already shuts down, which might
cause dangling characters to show up in hardware
queues when restarting the device.
Signed-off-by: NFabian Godehardt <fg@emlix.com>
Signed-off-by: NOskar Schirmer <os@emlix.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

upper layers, namely line discipline, need to be notified
when transmission of more data is possible. For spurious
cases, where IRQ handling does not supply notification
for sure, it is given additionally here, when data has just
been transmitted and space in the buffer will most probably
be available.
Signed-off-by: NFabian Godehardt <fg@emlix.com>
Signed-off-by: NOskar Schirmer <os@emlix.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

"have_rtscts" is assigned 1, while it is declared
int:1, two's complement, which can hold 0 and -1
only. The code works, as the upper bits are cut
off, and tests are done against 0 only.

Nonetheless, correctly declaring the bit field
as unsigned int:1 renders the code more robust.
Signed-off-by: NDaniel Glöckner <dg@emlix.com>
Signed-off-by: NOskar Schirmer <os@emlix.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NOskar Schirmer <os@emlix.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The driver only handles speeds but it fails to return the current values
for the hardware features it does not support.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Driver for the UART found in the Timberdale FPGA
Signed-off-by: NRichard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The UART RX handling code isn't exactly speeding, so don't go disabling
all interrupts when processing the buffer.  Just disable the relevant DMA
interrupt.  This greatly improves latency of the system when utilizing the
UART.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

05000231 - UART STB Bit Incorrectly Affects Receiver Setting
For processors affected by this, we cannot safely allow CSTOPB to be set
as the UART will then be unable to properly clock in bytes.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add some comments for how these anomalies are addressed:

05000215 - UART TX Interrupt Masked Erroneously
We always clear ETBEI within last UART TX interrupt to end
a string.  It is always set when starting a new tx transfer.

05000099 - UART Line Status Register (UART_LSR) Bits Are Not Updated at
the Same Time
This anomaly affects driver only in POLL code where multi bits of
UART_LSR are checked. It doesn't affect current bfin_5xx.c driver.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This bug is caused by irregular behavior of DMA register CURR_X_COUNT
and CURR_Y_COUNT when an auto restart uart rx DMA run to last byte in
DMA buffer, trigger the interrupt and stay at this possiton. The status
of current x and y is 0:7 instead of 512:8 or 0:8. The driver doesn't
take care of this case when calculating the position.

URL: http://blackfin.uclinux.org/gf/tracker/5063Reported-by: NTomasz Motylewski <t.motylewski@bfad.de>
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add a SSYNC() into bfin_serial_dma_tx_chars() to ensure DMA registers are
written with new data otherwise we might miss a byte or two when the
system is under load.  PIO mode is OK though.
Signed-off-by: NGraf Yang <graf.yang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Since we already setup the early console UART in
arch/blackfin/kernel/early_printk.c, and common functions which are
enabled from the .setup will override the proper settings later, don't
fill in these structures.  Otherwise we get mangled baudrate settings when
using early_printk.
Signed-off-by: NRobin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>