Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With commit d1e7925e ("bnxt_en: Centralize logic to reserve rings."),
ring allocation for combined rings has become stricter.  A combined
ring must now have an rx-tx ring pair.  The pre-set max. for combined
rings should now be min(rx, tx).

Fixes: d1e7925e ("bnxt_en: Centralize logic to reserve rings.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the HWRM_NVM_INSTALL_UPDATE command fails with the error code
NVM_INSTALL_UPDATE_CMD_ERR_CODE_FRAG_ERR, retry the command with
a new flag to allow defragmentation.  Since we are checking the
response for error code, we also need to take the mutex until
we finish reading the response.
Signed-off-by: NKshitij Soni <kshitij.soni@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add logic for an extra set of TX rings for XDP.  If enabled, this
set of TX rings equals the number of RX rings and shares the same
IRQ as the RX ring set.  A new field bp->tx_nr_rings_xdp is added
to keep track of these TX XDP rings.  Adjust all other relevant functions
to handle bp->tx_nr_rings_xdp.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, bnxt_setup_tc() and bnxt_set_channels() have similar and
duplicated code to check and reserve rx and tx rings.  Add a new
function bnxt_reserve_rings() to centralize the logic.  This will
make it easier to add XDP_TX support which requires allocating a
new set of TX rings.

Also, the tx ring checking logic in bnxt_setup_msix() can be removed.
The rings have been reserved before hand.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add LED blinking code to support ethtool -p on the PF.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to properly support TX rate limiting in SRIOV VF functions or
NPAR functions, firmware needs better control over tx ring allocations.
The new scheme requires the driver to reserve the number of tx rings
and to query to see if the requested number of tx rings is reserved.
The driver will use the new scheme when the firmware interface spec is
1.6.1 or newer.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Accept ipv6 flows in .ndo_rx_flow_steer() and support ETHTOOL_GRXCLSRULE
ipv6 flows.
Signed-off-by: NMichael Chan <michael.chan@broadocm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The advertising field is closely related to the auto_link_speeds field.
The former is the user setting while the latter is the firmware setting.
Both should be u16.  We should use the advertising field in
bnxt_get_link_ksettings because the auto_link_speeds field may not
be updated with the latest from the firmware yet.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Report PFC statistics to ethtool -S and DCBNL.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To display and modify the RSS hash.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Restart autoneg if autoneg is enabled.
Signed-off-by: NDeepak Khungar <deepak.khungar@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The existing code is inconsistent in reporting and accepting the combined
channel count.  bnxt_get_channels() reports maximum combined as the
maximum rx count.  bnxt_set_channels() accepts combined count that
cannot be bigger than max rx or max tx.

For example, if max rx = 2 and max tx = 1, we report max supported
combined to be 2.  But if the user tries to set combined to 2, it will
fail because 2 is bigger than max tx which is 1.

Fix the code to be consistent.  Max allowed combined = max(max_rx, max_tx).
We will accept a combined channel count <= max(max_rx, max_tx).
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using Ethtool flashdev command, entire NVM package (*.pkg) files
may now be staged into the "update" area of the NVM and subsequently
verified and installed by the firmware using the newly introduced
command: NVM_INSTALL_UPDATE.

We also introduce use of the new firmware command FW_SET_TIME so that the
NVM-resident package installation log contains valid time-stamps.
Signed-off-by: NRob Swindell <Rob.Swindell@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The hardware is unable to drop rx packets not matching the RX filters.  To
workaround it, we create a special VNIC and configure the hardware to
direct all packets not matching the filters to it.  We then setup the
driver to drop packets received on this VNIC.

This patch creates the infrastructure for this VNIC, reserves a
completion ring, and rx rings.  Only shared completion ring mode is
supported.  The next 2 patches add a NAPI to handle packets from this
VNIC and the setup of the VNIC.
Signed-off-by: NPrashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rc is not initialized so it can contain garbage if it is not
set by the call to bnxt_read_sfp_module_eeprom_info. Ensure
garbage is not returned by initializing rc to 0.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Acked-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The allowable range is 0.25 seconds to 1 second interval.  Default is
1 second.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support to the Ethtool FLASHDEV command handler for additional
firmware types to cover all the on-chip processors.
Signed-off-by: NRob Swindell <rob.swindell@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Upon successful mgmt processor firmware update, request a self
reset upon next PCIe reset (e.g. system reboot).
Signed-off-by: NRob Swindell <rob.swindell@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To support Secure Firmware Update, we must be able to allocate
a staging area in the Flash.  This patch adds support for the
"update" type to tell firmware to do that.
Signed-off-by: NRob Swindell <rob.swindell@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Returning 0 for doing nothing is confusing to the user.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To fully support 25G and 50G link settings.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some cards do not support autoneg.  The current code does not prevent the
user from enabling autoneg with ethtool on such cards, causing confusion.
Firmware provides the autoneg capability information and we just need to
store it in the support_auto_speeds field in bnxt_link_info struct.
The ethtool set_settings() call will check this field before proceeding
with autoneg.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NPAR type is read from bnxt_hwrm_func_qcfg.  Do not allow changing link
parameters if in NPAR mode sinc ethe port is shared among multiple
partitions.  The link parameters are set up by firmware.
Signed-off-by: NSatish Baddipadige <sbaddipa@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support to fetch the SFP EEPROM settings from the firmware
and display it via the ethtool -m command.  We support SFP+ and QSFP
modules.

v2: Fixed a bug in bnxt_get_module_eeprom() found by Ben Hutchings.
Signed-off-by: NAjit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When there is only 1 MSI-X vector or in INTA mode, tx and rx pre-set
max channel parameters are shown incorrectly in ethtool -l.  With only 1
vector, bnxt_get_max_rings() will return -ENOMEM.  bnxt_get_channels
should check this return value, and set max_rx/max_tx to 0 if it is
non-zero.
Signed-off-by: NSatish Baddipadige <sbaddipa@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

10GBaseT devices must autonegotiate to determine master/slave clocking.
Disallow forced speed in ethtool .set_settings() for these devices.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If autoneg is off, we should always report the speed and duplex settings
even if it is link down so the user knows the current settings.  The
unknown speed and duplex should only be used for autoneg when link is
down.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check that the forced speed is a valid speed supported by firmware.
If not supported, return -EINVAL.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow users to get|set EEE parameters.

v2: Added comment for preserving the tx_lpi_timer value in get_eee.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. Add bnxt_hwrm_set_eee() function to setup EEE firmware parameters based
on the bp->eee settings.
2. The new function bnxt_eee_config_ok() will check if EEE parameters need
to be modified due to autoneg changes.
3. bnxt_hwrm_set_link() has added a new parameter to update EEE.  If the
parameter is set, it will call bnxt_hwrm_set_eee().
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Get EEE capability and the initial EEE settings from firmware.
Add "EEE is active | not active" to link up dmesg.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make use of the new AUTONEG_PAUSE bit in the new interface to better
control autoneg flow control settings, independent of RX and TX
advertisement settings.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use new field names in API structs and stop using deprecated fields
auto_link_speed and auto_duplex in phy_cfg/phy_qcfg structs.

Update copyright year to 2016.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To report flow control tx/rx settings accurately regardless of autoneg
setting, we should use link_info->req_flow_ctrl.  Before this patch,
the reported settings were only correct when autoneg was on.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Include the more useful port statistics in ethtool -S for the PF device.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow all autoneg speeds aupported by firmware to be advertised.  If
the advertising parameter is 0, then all supported speeds will be
advertised.

Remove BNXT_ALL_COPPER_ETHTOOL_SPEED which is no longer used as all
supported speeds can be advertised.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The supported bits and advertising bits in ethtool have the same
definitions.  The same is true for the firmware bits.  So use the
common function to handle the conversion for both supported and
advertising bits.

v2: Don't use parentheses on function return.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

And report actual pause settings to ETHTOOL_GPAUSEPARAM to let ethtool
resolve the actual pause settings.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Include the conversion of pause bits and add one extra call layer so
that the same refactored function can be reused to get the link partner
advertisement bits.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>