USB generic driver
Add a mechanism to specify source names of selector units,
and add such names for the SB Audigy 2 NX.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

USB generic driver
In the streamX proc file, show the exact number of samples per
USB frame as 16.16 hexadecimal floating point value.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

USB generic driver
Add a mixer control map for the SB Audigy 2 NX so
that we get meaningful mixer control names.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

VIA82xx driver
Report by Ronny V. Vindenes <s864@ii.uib.no>
Add dxs_support=5 for MSI K8T Neo-FIS2R.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

HDA Codec driver
Fix and cleanup of CM9880 automatic PIN configuration.
snd_hda_codec_setup_stream() doesn't do anything when NID is 0.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

HDA generic driver
Show the jack type of each PIN default configuration entry.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

HDA generic driver
Fix a typo in comments.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

USB generic driver,USB USX2Y
Without this patch, some usb kobjects, which are parents to
the usx2y's kobjects can be freed before the usx2y's.
This led to an oops in get_kobj_path_length() and a dead
keyboard, when the usx2y's kobjects were freed.
The patch ensures the correct sequence.
Tested ok on kernel 2.6.12-rc2.
Signed-off-by: NKarsten Wiese <annabellesgarden@yahoo.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

EMU10K1/EMU10K2 driver
When building with gcc -W sound/pci/emu10k1/emupcm.c produces this little
warning in 2.6.12-rc2-mm3 :
  sound/pci/emu10k1/emupcm.c:265: warning: 'inline' is not at beginning of
declaration
No big deal, but trivial to fix.
Signed-off-by: NJesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

VIA82xx driver
Added dxs_support=5 entry for Insight P4-ITX.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

ALSA Core
Increase the timer protocl number (to distinguish the fix for TREAD ioctls).
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

HDA Codec driver
Misc clean up: move the definitions of constants for pinctl to a single place.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

HDA Codec driver
Removed the dead (duplicated) code.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

HDA Codec driver
Added the support of AD1981HD and AD1983 codecs.
Including the fix for AD1986A.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

HDA generic driver,HDA Codec driver
Add initial SigmaTel codec support for 9200 and 922x. Note that
this hda patch relies on the configuration default registers to
be set correctly (normally by BIOS/firmware) in order for it to
set up pin widgets properly. There's a test switch in the patch
so it will work with the SigmaTel reference boards that are usually
plugged into a system that doesn't set the configuration default
registers. It supports 2 channel analog out and line/mic in. I
plan to add >2 channel support and spdif support shortly.
Please apply.
Signed-off-by: NMatt <matt@embeddedalley.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

HDA Codec driver,HDA generic driver
Fix some vref defines so they are valid for the different bits in
the pin cap and pin control registers. Please apply.
Signed-off-by: NMatt <matt@embeddedalley.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

AC97 Codec
The handling of shared surround/clfe output jacks with line/mic-in
on some AC97 codecs is improved.

Instead of 'Line-In As Surround' or 'Mic As Center/LFE' switch, two
new enum controls are introduced: 'Channel Mode' and 'Surround Jack Mode'.
The formar changes the current output mode among 2, 4 and 6-channels.
The latter controls whether the jacks are shared or independent.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

ALSA Core
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

ALSA<-OSS emulation
Fix the noisy capture on some hardwares over OSS emulation.
Change back to avail_min = period_size for capture direction.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

PCM Midlevel,CA0106 driver,EMU10K1/EMU10K2 driver
Fix by Guillaume Chazarain <guichaz@yahoo.fr>:

Some tunables in /proc have a write() function, but as their
permission does not reflect it, it can be confusing to the user.

So here is a patch that corrects the mode of those files. Note that I
have only tested the 'xrun_debug' entry.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

EMU10K1/EMU10K2 driver
Fix compile warnings regarding the unused variables/functions.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Documentation,ALS4000 driver,ATIIXP driver,ATIIXP-modem driver
AZT3328 driver,BT87x driver,CMIPCI driver,CS4281 driver
ENS1370/1+ driver,ES1938 driver,ES1968 driver,FM801 driver
Intel8x0 driver,Intel8x0-modem driver,Maestro3 driver,RME32 driver
RME96 driver,SonicVibes driver,VIA82xx driver,VIA82xx-modem driver
ALI5451 driver,au88x0 driver,CA0106 driver,CS46xx driver
EMU10K1/EMU10K2 driver,HDA Intel driver,ICE1712 driver,ICE1724 driver
KORG1212 driver,MIXART driver,NM256 driver,RME HDSP driver
RME9652 driver,Trident driver,Digigram VX222 driver,YMFPCI driver
Replace the obsolete pci_module_init() with pci_register_driver().
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

VIA82xx driver
Fix SPDIF rate setting with dxs_support=4.  It should be 48k fixed.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Documentation,VIA82xx driver
Add support for full sample rate conversion capabilities of DXS
channels present in VIA VT8233/5/7 controllers:

- any sample rate in the 8000 ... 48000 Hz range is supported even if
  the AC'97 codec supports only 48000 Hz output;

- different DXS channels can use different sample rates at the same
  time (the controller performs required sample rate conversion and
  mixing in hardware).
Signed-off-by: NSergey Vlasov <vsu@altlinux.ru>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

FM801 driver
The Gallant Odyssey Sound 4 card is based on the ForteMedia FM801
chip, but has a different PCI ID.
Signed-off-by: NSergey Vlasov <vsu@altlinux.ru>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

YMFPCI driver
This patch removes some dead code found by the Coverity checker.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

ICE1712 driver
Provides preliminary support for the Terratec Phase 28 card.
Not extensively tested and probably buggy, but it seems to work.
Signed-off-by: NSimone Zinanni <simone@develer.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

EMU10K1/EMU10K2 driver
when using the p16v HD device.
Signed-off-by: NJames Courtier-Dutton <James@superbug.co.uk>

EMU10K1/EMU10K2 driver
Signed-off-by: NJames Courtier-Dutton <James@superbug.co.uk>

EMU10K1/EMU10K2 driver
Although we can set 44100 as the output rate, the SPDIF can do it, but the Analog output cannot.
The SPDIF has the bug, whereby the Left channel arrives one sample late, so although we don't do any resampling,
it is not good for AC3 non-audio output.
Signed-off-by: NJames Courtier-Dutton <James@superbug.co.uk>

EMU10K1/EMU10K2 driver
Signed-off-by: NJames Courtier-Dutton <James@superbug.co.uk>

HDA Codec driver
Patch by C.L. Tien <cltien@cmedia.com.tw>:

The patch makes cm9880 to choose multi-channel jacks automatically.

1. I found the current code has basic_init, which already includes
   necessary controls for 6-stack initialization, so I don't need
   another model.

2. I add a new model 'auto' to let the driver find a. if there are
   option real panel/front panel, b. the jacks to be used for multichannel.

Because the jack color are based on MS's channel sequence, so the 'auto'
model will pick the same jacks for multichannel MS uses. I did this to
hope to minimize users questions. These code can also be applied to other
codecs but I don't have any to test.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

ALSA sequencer
The last change to reduce stack usage did not adjust the parameter to
SNDRV_SEQ_IOCTL_SET_CLIENT_IOCTL which resulted in passing the address
of the pointer instead of the structure.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

AC97 Codec
Separated ac97 registers reset for audio and modem (or both) as recommended
in AC97 spec.
Signed-off-by: NSasha Khapyorsky <sashak@smlink.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

AC97 Codec
This (especially 12000 -> 8000 sample rate replace) fix popular
'MC97 converters.. not ready' error with modem codecs initializations.
Signed-off-by: NSasha Khapyorsky <sashak@smlink.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Intel8x0-modem driver
With some intel based ac97 modems codec access semaphore is not cleared
after 0x54 AC97 register (GPIO_STATUS) reads. This may causes problems
with newly applied modem mixer (Off-hook switch) and in other cases.
Signed-off-by: NSasha Khapyorsky <sashak@smlink.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

AC97 Codec
- Added CM9780 patch
- Fix the SPDIF support on CM9761/CM9780
- Allow the generic enum callback to pass any number (not power of 2)
  as the value mask
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

AC97 Codec
Removed unused variables (the old control definitions).
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

EMU10K1/EMU10K2 driver
Check ther revision to detect non-listed audigy 2 boards.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

USB generic driver
This patch adds quirks to support 24-bit PCM I/O in the 'Advanced
Driver' mode of the BOSS GS-10.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>