now that we provide generic register/unregister
debugging messages from udc-core, we can remove
the same messages from this driver.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

future patches will remove the extra 'driver'
argument to ->udc_stop(), in order to do that,
we must make sure that our UDC does not rely
on it first.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The drivers should use dmaengine_terminate_all() or dmaengine_slave_config()
API instead of accessing the device_control which will be deprecated soon
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The memory subsystem has already had similar message for it.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The memory subsystem has already had similar message for it.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The memory subsystem has already had similar message for it.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The memory subsystem has already had similar message for it.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The memory subsystem has already had similar message for it.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The memory subsystem has already had similar message for it.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

So testing managed to configure musb in DMA mode but not load the
matching cppi41 driver for DMA. This results in

|musb-hdrc musb-hdrc.0.auto: Failed to request rx1.
|musb-hdrc musb-hdrc.0.auto: musb_init_controller failed with status -517
|platform musb-hdrc.0.auto: Driver musb-hdrc requests probe deferral

which is "okay". Once the driver is loaded we re-try probing and
everyone is happy. Until then if you try suspend say
    echo mem > /sys/power/state
then you go boom

|Unable to handle kernel NULL pointer dereference at virtual address 000003a4
|pgd = cf50c000
|[000003a4] *pgd=8f6a3831, *pte=00000000, *ppte=00000000
|Internal error: Oops: 17 [#1] ARM
|PC is at dsps_suspend+0x18/0x9c [musb_dsps]
|LR is at dsps_suspend+0x18/0x9c [musb_dsps]
|pc : [<bf08e268>] lr : [<bf08e268>] psr: a0000013
|sp : cbd97e00 ip : c0af4394 fp : 00000000
|r10: c0831d90 r9 : 00000002 r8 : cf6da410
|r7 : c03ba4dc r6 : bf08f224 r5 : 00000000 r4 : cbc5fcd0
|r3 : bf08e250 r2 : bf08f264 r1 : cf6da410 r0 : 00000000
|[<bf08e268>] (dsps_suspend [musb_dsps]) from [<c03ba508>] (platform_pm_suspend+0x2c/0x54)
|Code: e1a04000 e9900041 e2800010 eb4caa8e (e59053a4)

because platform_get_drvdata(glue->musb) returns a NULL pointer as long as the
device is not fully probed.
Tested-by: NGeorge Cherian <george.cherian@ti.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Commit 468bcc2a ("usb: musb: dsps: kill OTG timer on suspend") stopped
the timer in suspend path but forgot the re-enable it in the resume
path. This patch fixes the behaviour.

Cc: <stable@vger.kernel.org> # v3.14+
Fixes 468bcc2a "usb: musb: dsps: kill OTG timer on suspend"
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

commit c58d80f5 ("usb: musb: Ensure that cppi41 timer gets armed on
premature DMA TX irq") fixed hrtimer scheduling bug. There is one left
which does not trigger that often.
The following scenario is still possible:

    lock(&x->lock);
    hrtimer_start(&x->t);
    unlock(&x->lock);

expires:
    t->function();
                                lock(&x->lock);
    lock(&x->lock);             if (!hrtimer_queued(&x->t))
                                        hrtimer_start(&x->t);
                                unlock(&x->lock);

    if (!list_empty(x->early_tx_list))
           ret = HRTIMER_RESTART;
->         hrtimer_forward_now(...)
    } else
           ret = HRTIMER_NORESTART;

    unlock(&x->lock);

and the timer callback returns HRTIMER_RESTART for an armed timer. This
is wrong and we run into the BUG_ON() in __run_hrtimer().
This can happens on SMP or PREEMPT-RT.
The patch fixes the problem by only starting the timer if the timer is
not yet queued.

Cc: stable@vger.kernel.org
Reported-by: NTorben Hohn <torbenh@linutronix.de>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
[bigeasy: collected information and created a patch + description based
          on it]
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Use the recently introduced usb_gadget_giveback_request() in favor of
direct invocation of the completion routine.

All places in drivers/usb/ matching "[-.]complete(" were replaced with a
call to usb_gadget_giveback_request(). This was compile-tested with all
ARM drivers enabled and runtime-tested for musb.
Signed-off-by: NMichal Sojka <sojka@merica.cz>
Acked-by: NFelipe Balbi <balbi@ti.com>
Tested-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

USB hub has started to use a workqueue instead of kthread. Let's update
the documentation and comments here and there.

This patch mostly just replaces "khubd" with "hub_wq". There are only few
exceptions where the whole sentence was updated. These more complicated
changes can be found in the following files:

	   Documentation/usb/hotplug.txt
	   drivers/net/usb/usbnet.c
	   drivers/usb/core/hcd.c
	   drivers/usb/host/ohci-hcd.c
	   drivers/usb/host/xhci.c
Signed-off-by: NPetr Mladek <pmladek@suse.cz>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixed typos in comments of various drivers/usb files
Signed-off-by: NMickael Maison <mickael.maison@gmail.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

if we don't make sure to kill the timer, it could
expire after we have already gated our clocks.

That will trigger a Data Abort exception because
we would try to access register while clock is gated.

Fix that bug.

Cc: <stable@vger.kernel.org> # v3.14+
Fixes 869c5978 (usb: musb: dsps: add support for suspend and resume)
Tested-by: NDave Gerlach <d-gerlach@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Intensive tests with USB audio devices connected to a musb host port
have shown reproducible pops and clicks in both the playback and the
capture stream.

These are related to how the early_tx hrtimer is set up, and it turns
out they can be fixed by reducing the timer's slack value from 40 to
25 us. Also, when the callback is ran without taking action, it should
be rescheduled 20 us later instead of 50 us.
Reported-and-tested-by: NSven Neumann <neumann@teufel.de>
Signed-off-by: NDaniel Mack <daniel@zonque.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

CPPI TX does not transmit ZLP for TX transfers which
- transfer size is multiple of EP packet size,
- and URB_ZERO_PACKET is set in urb->transfer_flags.

The fix is transmitting the ZLP using PIO mode after the CPPI TX is
done.

Validated using the following usbtest write case in MUSB host mode.

  # testusb -t1 -c1
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The prefix suggests the number should be printed in hex, so use
the %x specifier to do that.

Found by using regex suggested by Joe Perches.
Signed-off-by: NHans Wennborg <hans@hanshq.net>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add sw_babble_control() logic to differentiate between transient
babble and real babble condition. Also add the SW babble control
register definitions.

Babble control register logic is implemented in the latest
revision of AM335x.

Find whether we are running on newer silicon. The babble control
register reads 0x4 by default in newer silicon as opposed to 0
in old versions of AM335x. Based on this enable the sw babble
control logic.
Signed-off-by: NGeorge Cherian <george.cherian@ti.com>
Tested-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Currently musb_platform_reset() is only used by dsps.
In case of BABBLE interrupt for other platforms the  musb_platform_reset()
is a NOP. In such situations no need to re-initialize the endpoints.
Also in the latest silicon revision of AM335x, we do have a babble recovery
mechanism without resetting the IP block. In preperation to add that support
its better to have a rest_done return for  musb_platform_reset().
Signed-off-by: NGeorge Cherian <george.cherian@ti.com>
Tested-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

During babble condition both first disconnect of devices are
initiated. Make sure MUSB controller is reset and re-initialized
after all disconnects.

To acheive this schedule a delayed work for babble recovery.

While at that convert udelay to usleep_range.
Refer Documentation/timers/timers-howto.txt
Signed-off-by: NGeorge Cherian <george.cherian@ti.com>
Tested-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

BABBLE and RESET share the same interrupt. The interrupt
is considered to be RESET if MUSB is in peripheral mode and
as a BABBLE if MUSB is in HOST mode.

Handle babble condition iff MUSB is in HOST mode.
Signed-off-by: NGeorge Cherian <george.cherian@ti.com>
Tested-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Following the name change of the NOP transceiver driver in commit
4525beeb (usb: phy: rename usb_nop_xceiv to usb_phy_generic), the
transceiver driver was no longer operable under its old name.

Register the transceiver driver before calling usb_get_phy() to make
sure we are noticed by an error message if it is not available.
Signed-off-by: NApelete Seketeli <apelete@seketeli.net>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The musb/cppi41 code installs a hrtimer to work around DMA completion
interrupts that have fired too early on AM335x hardware. This timer
is currently programmed to first fire 140 microseconds after the DMA
completion callback. According to the commit which introduced it
(a655f481, "usb: musb: musb_cppi41: handle pre-mature TX complete
interrupt"), that value is is considered a 'rule of thumb' that worked
well with the test case described in the commit log.

Test show, however, that for USB audio devices and much smaller packet
sizes, the timer has to fire earlier in order to correctly handle the audio
stream. The original test case had output transfer sizes of 1514 bytes, and
a delay of 140 microseconds. For audio devices with 24 bytes channel size, 3
microseconds seem to work well.

Hence, let's assume that the time it takes to clear the bit correlates with
the number of bytes transferred. The referenced commit log mentions such a
suspicion as well. Let the timer fire in cppi41_channel->total_len/10
microseconds to correctly handle both cases.

Also, shorten the interval in which the timer fires again in case of
a non-empty early_tx list.

With these changes in place, both FS and HS audio devices appear to work
well on AM335x hardware.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Reported-by: NSebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This reverts commit 1af54b7a.

The commit tried to address cases in which isochronous transfers are 'not
reliable', most probably in the tests conducted, polling for the
MUSB_TXCSR_TXPKTRDY bit in MUSB_TXCSR is done too late.

Hence, it installs a work struct which basically busy-polls for the bit in a
rather agressive way by rescheduling the work if the FIFO is not empty. With
USB audio devices, tests have shown that it takes approximately 100
iterations of the asynchronous worker until the FIFO signals completion,
which leads to 100% CPU loads when streaming audio.

The issue the patch tried to address can be handled differently, which is
what the next patch does.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Reported-by: NSebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Just a cosmetic cleanup with no functional change.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Before accessing any of an endpoint's CSR registers, make sure the
correct endpoint is selected. Otherwise, data read from or written to
the registers is likely to affect the wrong endpoint as long as the
connected device has more than one endpoint.

This, of course, leads to all sorts of strange effects such as stream
starvation and driver internal state machine confusion due to spurious
interrupts.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The musb/cppi41 glue layer is capable of handling transactions that span
over more than one USB packet by reloading the DMA descriptors
partially. An urb is considered completed when either its transfer
buffer has been filled entirely (actual_length ==
transfer_buffer_length) or if a packet in the stream has less bytes than
the endpoint's wMaxPacketSize.

Once one of the above conditions is met, musb_dma_completion() is called
from cppi41_trans_done(). However, the final decision whether or not to
return the urb to its owner is made by the core and its determination of
the variable 'done' in musb_host_rx(). This code has currently no way of
knowing what the size of the last packet was, and whether or not to
give back the urb due to a short read.

Fix this by introducing a new boolean flag in 'struct dma_channel', and
set it from musb_cppi41.c. If set, it will make the core do what the
DMA layer decided and complete the urb.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Acked-by: NGeorge Cherian <george.cherian@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The datasheet says that MUSB_TXCSR_FLUSHFIFO is only valid when
MUSB_TXCSR_TXPKTRDY is set as well.

With this patch applied, the warning in this function does no longer
kick in when an USB soundcard is unplugged while the stream is active.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

On AM33xx platforms, unplugging a device in the middle of an active
transfer leads to a drop of MUSB_DEVCTL_HM in MUSB_DEVCTL before the
system is informed about a disconnect. This consequently makes the musb
core call the gadget code to handle the interrupt request, which then
crashes the kernel because the relevant pointers haven't been set up
for gadget mode.

To fix this, use is_host_active() rather than (devctl & MUSB_DEVCTL_HM)
in musb_interrupt() and musb_dma_completion() to detect whether the
controller is in host or peripheral mode. This information is provided
by the driver logic and does not rely on register contents.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Just a little cleanup that removes unnecessary casts.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Acked-by: NGeorge Cherian <george.cherian@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

commit 943c1397 "usb: musb: dsps: implement ->set_mode()"
should have made it possible to use the driver with boards that have
the USBID pin unconnected. This doesn't actually work, since the
driver uses the wrong base address to access the mode register.
Furthermore it uses different base addresses in different places to
access the same register (phy_utmi).
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

For DSPS platform usb_phy_vbus(_off/_on) are NOPs.
So during musb_platform_reset() call usb_phy(_shutdown/_init)
Signed-off-by: NGeorge Cherian <george.cherian@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

There is a risk that the variable will be used without being initialized.

This was largely found by using a static code analysis program called cppcheck.
Signed-off-by: NRickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch moves data allocated using kzalloc to managed data allocated
using devm_kzalloc and cleans now unnecessary kfrees in probe and remove
functions. Also, a label is done away with and err2 and err3 renamed.

The following Coccinelle semantic patch was used for making the change:

@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
  .probe = probefn,
  .remove = removefn,
};

@prb@
identifier platform.probefn, pdev;
expression e, e1, e2;
@@
probefn(struct platform_device *pdev, ...) {
  <+...
- e = kzalloc(e1, e2)
+ e = devm_kzalloc(&pdev->dev, e1, e2)
  ...
?-kfree(e);
  ...+>
}

@rem depends on prb@
identifier platform.removefn;
expression e;
@@
removefn(...) {
  <...
- kfree(e);
  ...>
}
Signed-off-by: NHimangi Saraogi <himangi774@gmail.com>
Acked-by: NJulia Lawall <julia.lawall@lip6.fr>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch moves data allocated using kzalloc to managed data allocated
using devm_kzalloc and cleans now unnecessary kfrees in probe and remove
functions. Also, the unnecesary labels are removed and linux/device.h is
added to make sure the devm_*() routine declarations are unambiguously
available.

The following Coccinelle semantic patch was used for making the change:

@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
  .probe = probefn,
  .remove = removefn,
};

@prb@
identifier platform.probefn, pdev;
expression e, e1, e2;
@@
probefn(struct platform_device *pdev, ...) {
  <+...
- e = kzalloc(e1, e2)
+ e = devm_kzalloc(&pdev->dev, e1, e2)
  ...
?-kfree(e);
  ...+>
}

@rem depends on prb@
identifier platform.removefn;
expression e;
@@
removefn(...) {
  <...
- kfree(e);
  ...>
}
Signed-off-by: NHimangi Saraogi <himangi774@gmail.com>
Acked-by: NJulia Lawall <julia.lawall@lip6.fr>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch moves data allocated using kzalloc to managed data allocated
using devm_kzalloc and cleans now unnecessary kfrees in probe and remove
functions. Also, a label is done away with and clk_get is replaced by it
corresponding devm version and the clk_puts are done away with. The
labels are renamed to make them ordered.

The following Coccinelle semantic patch was used for making the change:

@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
  .probe = probefn,
  .remove = removefn,
};

@prb@
identifier platform.probefn, pdev;
expression e, e1, e2;
@@
probefn(struct platform_device *pdev, ...) {
  <+...
- e = kzalloc(e1, e2)
+ e = devm_kzalloc(&pdev->dev, e1, e2)
  ...
?-kfree(e);
  ...+>
}

@rem depends on prb@
identifier platform.removefn;
expression e;
@@
removefn(...) {
  <...
- kfree(e);
  ...>
}
Signed-off-by: NHimangi Saraogi <himangi774@gmail.com>
Acked-by: NJulia Lawall <julia.lawall@lip6.fr>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch introduces the use of managed interfaces for clk_get and
kzalloc and removes the corresponding free function calls in the probe
and remove functions.
Signed-off-by: NHimangi Saraogi <himangi774@gmail.com>
Acked-by: NJulia Lawall <julia.lawall@lip6.fr>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

There is no reason for the register accessor functions not to adhere
to the CodingStyle rules.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>