The USB 2.0 specification says that bMaxPower is the maximum power
consumption expressed in 2 mA units and the USB 3.0 specification says
that it is expressed in 8 mA units.
This patch adds a helper function usb_get_max_power() which computes the
value based on config & usb_device's speed value. The the device descriptor
dump computes the value on its own.

Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Refactor hub_port_wait_reset into a small loop to wait for the port
reset to be complete, and then a larger block to deal with the final
port status.  This patch should not change any current behavior.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>

Change the code that manually issues a Set Port Feature(Link State) to
use the new helper function hub_set_port_link_state().
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>

A USB 3.0 device can transition to the Inactive state if a U1 or U2 exit
transition fails.  The current code in hub_events simply issues a warm
reset, but does not call any pre-reset or post-reset driver methods (or
unbind/rebind drivers without them).  Therefore the drivers won't know
their device has just been reset.

hub_events should instead call usb_reset_device.  This means
hub_port_reset now needs to figure out whether it should issue a warm
reset or a hot reset.

Remove the FIXME note about needing disconnect() for a NOTATTACHED
device.  This patch fixes that.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>

When a hot reset fails on a USB 3.0 port, the current port reset code
recursively calls hub_port_reset inside hub_port_wait_reset.  This isn't
ideal, since we should avoid recursive calls in the kernel, and it also
doesn't allow us to issue multiple warm resets on reset failures.

Rip out the recursive call.  Instead, add code to hub_port_reset to
issue a warm reset if the hot reset fails, and try multiple warm resets
before giving up on the port.

In hub_port_wait_reset, remove the recursive call and re-indent.  The
code is basically the same, except:

1. It bails out early if the port has transitioned to Inactive or
Compliance Mode after the reset completed.

2. It doesn't consider a connect status change to be a failed reset.  If
multiple warm resets needed to be issued, the connect status may have
changed, so we need to ignore that and look at the port link state
instead.  hub_port_reset will now do that.

3. It unconditionally sets udev->speed on all types of successful
resets.  The old recursive code would set the port speed when the second
hub_port_reset returned.

The old code did not handle connected devices needing a warm reset well.
There were only two situations that the old code handled correctly: an
empty port needing a warm reset, and a hot reset that migrated to a warm
reset.

When an empty port needed a warm reset, hub_port_reset was called with
the warm variable set.  The code in hub_port_finish_reset would skip
telling the USB core and the xHC host that the device was reset, because
otherwise that would result in a NULL pointer dereference.

When a USB 3.0 device reset migrated to a warm reset, the recursive call
made the call stack look like this:

hub_port_reset(warm = false)
        hub_wait_port_reset(warm = false)
                hub_port_reset(warm = true)
                        hub_wait_port_reset(warm = true)
                        hub_port_finish_reset(warm = true)
                        (return up the call stack to the first wait)

        hub_port_finish_reset(warm = false)

The old code didn't want to notify the USB core or the xHC host of device reset
twice, so it only did it in the second call to hub_port_finish_reset,
when warm was set to false.  This was necessary because
before patch two ("USB: Ignore xHCI Reset Device status."), the USB core
would pay attention to the xHC Reset Device command error status, and
the second call would always fail.

Now that we no longer have the recursive call, and warm can change from
false to true in hub_port_reset, we need to have hub_port_finish_reset
unconditionally notify the USB core and the xHC of the device reset.

In hub_port_finish_reset, unconditionally clear the connect status
change (CSC) bit for USB 3.0 hubs when the port reset is done.  If we
had to issue multiple warm resets for a device, that bit may have been
set if the device went into SS.Inactive and then was successfully warm
reset.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>

The next patch will refactor the hub port code to rip out the recursive
call to hub_port_reset on a failed hot reset.  In preparation for that,
make sure all code paths can deal with being called with a NULL udev.
The usb_device will not be valid if warm reset was issued because a port
transitioned to the Inactive or Compliance Mode on a device connect.

This patch should have no effect on current behavior.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>

The EHCI host controller needs to prevent EHCI initialization when the
UHCI or OHCI companion controller is in the middle of a port reset.  It
uses ehci_cf_port_reset_rwsem to do this.  USB 3.0 hubs can't be under
an EHCI host controller, so it makes no sense to down the semaphore for
USB 3.0 hubs.  It also makes the warm port reset code more complex.

Don't down ehci_cf_port_reset_rwsem for USB 3.0 hubs.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>

An empty port can transition to either Inactive or Compliance Mode if a
newly connected USB 3.0 device fails to link train.  In that case, we
issue a warm reset.  Some devices, such as John's Roseweil eusb3
enclosure, slip back into Compliance Mode after the warm reset.

The current warm reset code does not check for device connect status on
warm reset completion, and it incorrectly reports the warm reset
succeeded.  This causes the USB core to attempt to send a Set Address
control transfer to a port in Compliance Mode, which will always fail.

Make hub_port_wait_reset check the current connect status and link state
after the warm reset completes.  Return a failure status if the device
is disconnected or the link state is Compliance Mode or SS.Inactive.

Make hub_events disable the port if warm reset fails.  This will disable
the port, and then bring it back into the RxDetect state.  Make the USB
core ignore the connect change until the device reconnects.

Note that this patch does NOT handle connected devices slipping into the
Inactive state very well.  This is a concern, because devices can go
into the Inactive state on U1/U2 exit failure.  However, the fix for
that case is too large for stable, so it will be submitted in a separate
patch.

This patch should be backported to kernels as old as 3.2, contain the
commit ID 75d7cf72 "usbcore: refine warm
reset logic"
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-by: NJohn Covici <covici@ccs.covici.com>
Cc: stable@vger.kernel.org

The port reset code bails out early if the current connect status is
cleared (device disconnected).  If we're issuing a hot reset, it may
also look at the link state before the reset is finished.

Section 10.14.2.6 of the USB 3.0 spec says that when a port enters the
Error state or Resetting state, the port connection bit retains the
value from the previous state.  Therefore we can't trust it until the
reset finishes.  Also, the xHCI spec section 4.19.1.2.5 says software
shall ignore the link state while the port is resetting, as it can be in
an unknown state.

The port state during reset is also unknown for USB 2.0 hubs.  The hub
sends a reset signal by driving the bus into an SE0 state.  This
overwhelms the "connect" signal from the device, so the port can't tell
whether anything is connected or not.

Fix the port reset code to ignore the port link state and current
connect bit until the reset finishes, and USB_PORT_STAT_RESET is
cleared.

Remove the check for USB_PORT_STAT_C_BH_RESET in the warm reset case,
because it's redundant.  When the warm reset finishes, the port reset
bit will be cleared at the same time USB_PORT_STAT_C_BH_RESET is set.
Remove the now-redundant check for a cleared USB_PORT_STAT_RESET bit
in the code to deal with the finished reset.

This patch should be backported to all stable kernels.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org

John's NEC 0.96 xHCI host controller needs a longer timeout for a warm
reset to complete.  The logs show it takes 650ms to complete the warm
reset, so extend the hub reset timeout to 800ms to be on the safe side.

This commit should be backported to kernels as old as 3.2, that contain
the commit 75d7cf72 "usbcore: refine
warm reset logic".
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-by: NJohn Covici <covici@ccs.covici.com>
Cc: stable@vger.kernel.org

If hot and warm reset fails, or a port remains in the Compliance Mode,
the USB core needs to be able to disable a USB 3.0 port.  Unlike USB 2.0
ports, once the port is placed into the Disabled link state, it will not
report any new device connects.  To get device connect notifications, we
need to put the link into the Disabled state, and then the RxDetect
state.

The xHCI driver needs to atomically clear all change bits on USB 3.0
port disable, so that we get Port Status Change Events for future port
changes.  We could technically do this in the USB core instead of in the
xHCI roothub code, since the port state machine can't advance out of the
disabled state until we set the link state to RxDetect.  However,
external USB 3.0 hubs don't need this code.  They are level-triggered,
not edge-triggered like xHCI, so they will continue to send interrupt
events when any change bit is set.  Therefore it doesn't make sense to
put this code in the USB core.

This patch is part of a series to fix several reports of infinite loops
on device enumeration failure.  This includes John, when he boots with
a USB 3.0 device (Roseweil eusb3 enclosure) attached to his NEC 0.96
host controller.  The fix requires warm reset support, so it does not
make sense to backport this patch to stable kernels without warm reset
support.

This patch should be backported to kernels as old as 3.2, contain the
commit ID 75d7cf72 "usbcore: refine warm
reset logic"
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-by: NJohn Covici <covici@ccs.covici.com>
Cc: stable@vger.kernel.org

When the USB core finishes reseting a USB device, the xHCI driver sends
a Reset Device command to the host.  The xHC then updates its internal
representation of the USB device to the 'Default' device state.  If the
device was already in the Default state, the xHC will complete the
command with an error status.

If a device needs to be reset several times during enumeration, the
second reset will always fail because of the xHCI Reset Device command.
This can cause issues during enumeration.

For example, usb_reset_and_verify_device calls into hub_port_init in a
loop.  Say that on the first call into hub_port_init, the device is
successfully reset, but doesn't respond to several set address control
transfers.  Then the port will be disabled, but the udev will remain in
tact.  usb_reset_and_verify_device will call into hub_port_init again.

On the second call into hub_port_init, the device will be reset, and the
xHCI driver will issue a Reset Device command.  This command will fail
(because the device is already in the Default state), and
usb_reset_and_verify_device will fail.  The port will be disabled, and
the device won't be able to enumerate.

Fix this by ignoring the return value of the HCD reset_device callback.

This commit should be backported to kernels as old as 3.2, that contain
the commit 75d7cf72 "usbcore: refine
warm reset logic".
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org

USB 3.0 hubs and roothubs will automatically transition a failed hot
reset to a warm (BH) reset.  In that case, the warm reset change bit
will be set, and the link state change bit may also be set.  Change
hub_port_finish_reset to unconditionally clear those change bits for USB
3.0 hubs.  If these bits are not cleared, we may lose port change events
from the roothub.

This commit should be backported to kernels as old as 3.2, that contain
the commit 75d7cf72 "usbcore: refine
warm reset logic".
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org

'new_interfaces' should be freed to avoid memory leak.

Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove conditional code based on CONFIG_HOTPLUG being false.  It's
always on now in preparation of it going away as an option.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The old parameter "port" is useless for phy notify, as one usb
phy is only for one usb port. New parameter "speed" stands for
the device's speed which is on the port, this "speed" parameter
is needed at some platforms which will do some phy operations
according to device's speed.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Tested-by: NMike Thompson <mpthompson@gmail.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

At commit 925aa46b, Richard Zhao
<richard.zhao@freescale.com> adds the phy notification callback
when port change occurs. In fact, this phy notification should
be added according to below rules:

1. Only set HW_USBPHY_CTRL.ENHOSTDISCONDETECT
during high speed host mode.
2. Do not set HW_USBPHY_CTRL.ENHOSTDISCONDETECT
during the reset and speed negotiation period.
3. Do not set HW_USBPHY_CTRL.ENHOSTDISCONDETECT
during host suspend/resume sequence.

Please refer: i.mx23RM(page: 413) for below rules.
http://www.freescale.com/files/dsp/doc/ref_manual/IMX23RM.pdf

Freescale i.MX SoC, i.mx23, i.mx28 and i.mx6(i.mx6SL does not
need to follow the 3rd rule) need to follow above rules.

Current code set connect notification (HW_USBPHY_CTRL.ENHOSTDISCONDETECT)
at hub_port_connect_change, it conflicts with above the 2th rule.

The correct notification setting method should be:
1. Set connect notify after the second bus reset.
2. Set disconnect notify after disconnection.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Tested-by: NMike Thompson <mpthompson@gmail.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

    It looks like I've run into some inconsistency in the USB stack behavior.

    The USB stack maintains, among others, two states for the attach
USB device: authorized and owned. Authorization state is accessible to
the user space code through correspondent sysfs files, the ownership
can be set by claiming the hub's port with ioctl call. Both state may
be set before the device is attached, by access the hub settings. When
the new device is attached, both authorization and ownership prevent
the kernel USB stack from setting the newly attached device
configuration, but when the device is authorized, the ownership state
is ignored. It looks like ignoring the ownership state on
authorization make the stack behavior inconsistent; it also prevents
the user space code from completely overriding configuration
selection, important for implementing workarounds for bugs in the
device configuration selection.

   The following patch makes the stack behavior more consistent, by
moving ownership test into usb_choose_configuration - the later
function is used both by generic_probe and usb_authorize_device
Signed-off-by: NJoseph Hindin <hindin@gmail.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 73d40660.

Martin Steigerwald reported that this change caused a hard lockup when
using USB if threadirqs are enabled.  Thomas pointed out that this patch
is incorrect, and can cause problems.  So revert it to get the
previously working functionality back.
Reported-by: NMartin Steigerwald <Martin@lichtvoll.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Chuansheng Liu <chuansheng.liu@intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1633) changes slightly the way usbcore handled
submissions of URBs that are already active.  It will now return
-EBUSY rather than -EINVAL, and it will call WARN_ONCE to draw
people's attention to the bug.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1631) fixes a bug that shows up when a config change
fails for a device under an xHCI controller.  The controller needs to
be told to disable the endpoints that have been enabled for the new
config.  The existing code does this, but before storing the
information about which endpoints were enabled!  As a result, any
second attempt to install the new config is doomed to fail because
xhci-hcd will refuse to enable an endpoint that is already enabled.

The patch optimistically initializes the new endpoints' device
structures before asking the device to switch to the new config.  If
the request fails then the endpoint information is already stored, so
we can use usb_hcd_alloc_bandwidth() to disable the endpoints with no
trouble.  The rest of the error path is slightly more complex now; we
have to disable the new interfaces and call put_device() rather than
simply deallocating them.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: NMatthias Schniedermeyer <ms@citd.de>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1621) removes the limit on the number of loops allowed
in hub_tt_work().  The value is arbitrary, and it's silly to have a
limit in the first place -- anything beyond the limit would not get
handled.

Besides, it's most unlikely that we'll ever need to clear more than a
couple of TT buffers at any time.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

dev_<level> calls take less code than dev_printk(KERN_<LEVEL>
and reducing object size is good.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch sets hub device's default autosuspend delay as 0 to
speedup bus suspend, see comments in code for details.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NMing Lei <ming.lei@canonical.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The hub status endpoint has a long 'bInterval', which is 255ms
for FS/LS device and 256ms for HS device according to USB 2.0 spec,
so the device connection change may be reported later more than 255ms
via status pipe.

The connection change in hub may have been happened already on the
downstream ports, but no status URB completes when it is killed
in hub_suspend(auto), so the connection change may be missed by some
buggy hub devices, which won't generate remote wakeup signal after
their remote wakeup is enabled and they are put into suspend state.

The problem can be observed at least on the below Genesys Logic, Inc.
hub devices:

	0x05e3,0x0606
	0x05e3,0x0608

In theory, there is no way to fix the problem completely, but we
can make it less likely to occur by this patch.

This patch introduces one quirk of HUB_QUIRK_CHECK_PORTS_AUTOSUSPEND
to check ports' change during hub_suspend(auto) for the buggy
devices. If ports' change is found, terminate the auto suspend and
return to working state.

So for the buggy hubs, if the connection change happend before
the ports' check, it can be handled correctly. If it happens between
the ports' check and enabling remote wakeup/entering suspend, it
will be missed. Considered the interval is quite short, it is very
less likely to happen during the window.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NMing Lei <ming.lei@canonical.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1620) speeds up USB root-hub resumes in the common case
where every enabled port has its suspend feature set (which currently
will be true for every runtime resume of the root hub).  If all the
enabled ports are suspended then resuming the root hub won't resume
any of the downstream devices.  In this case there's no need for a
Resume Recovery delay, because that delay is meant to give devices a
chance to get ready for active use.

To keep track of the port suspend features, the patch adds a
"port_is_suspended" flag to struct usb_device.  This has to be tracked
separately from the device's state; it's entirely possible for a USB-2
device to be suspended while the suspend feature on its parent port is
clear.  The reason is that devices will go into suspend whenever their
parent hub does.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reviewed-by: NPeter Chen <peter.chen@freescale.com>
Tested-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1619) improves the interface to the "hub_for_each_child"
macro.  The name clearly suggests that the macro iterates over child
devices; it does not suggest that the loop will also iterate over
unnconnected ports.

The patch changes the macro so that it will skip over unconnected
ports and iterate only the actual child devices.  The two existing
call sites are updated to avoid testing for a NULL child pointer,
which is now unnecessary.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We defined bus_to_hdc for that, use it.
Signed-off-by: NYuanhan Liu <yliu.null@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

flush_work_sync and flush_work are now the same and flush_work_sync
has been deprecated. This fixes the following warning:

drivers/usb/core/hub.c: In function hub_quiesce:
drivers/usb/core/hub.c:1216:3: warning: flush_work_sync is deprecated (declared at include/linux/workqueue.h:448) [-Wdeprecated-declarations]
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NOctavian Purdila <octavian.purdila@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There is a race condition in the USB hub code with regard to handling
TT clear requests that can get the HCD driver in a deadlock. Usually
when an TT clear request is scheduled it will be executed immediately:

<7>[    6.077583] usb 2-1.3: unlink qh1-0e01/f4d4db00 start 0 [1/2 us]
<3>[    6.078041] usb 2-1: clear tt buffer port 3, a3 ep2 t04048d82
<7>[    6.078299] hub_tt_work:731
<7>[    9.309089] usb 2-1.5: link qh1-0e01/f4d506c0 start 0 [1/2 us]
<7>[    9.324526] ehci_hcd 0000:00:1d.0: reused qh f4d4db00 schedule
<7>[    9.324539] usb 2-1.3: link qh1-0e01/f4d4db00 start 0 [1/2 us]
<7>[    9.341530] usb 1-1.1: link qh4-0e01/f397aec0 start 2 [1/2 us]
<7>[   10.116159] usb 2-1.3: unlink qh1-0e01/f4d4db00 start 0 [1/2 us]
<3>[   10.116459] usb 2-1: clear tt buffer port 3, a3 ep2 t04048d82
<7>[   10.116537] hub_tt_work:731

However, if a suspend operation is triggered before hub_tt_work is
scheduled, hub_quiesce will cancel the work without notifying the HCD
driver:

<3>[   35.033941] usb 2-1: clear tt buffer port 3, a3 ep2 t04048d80
<5>[   35.034022] sd 0:0:0:0: [sda] Stopping disk
<7>[   35.034039] hub 2-1:1.0: hub_suspend
<7>[   35.034067] usb 2-1: unlink qh256-0001/f3b1ab00 start 1 [1/0 us]
<7>[   35.035085] hub 1-0:1.0: hub_suspend
<7>[   35.035102] usb usb1: bus suspend, wakeup 0
<7>[   35.035106] ehci_hcd 0000:00:1a.0: suspend root hub
<7>[   35.035298] hub 2-0:1.0: hub_suspend
<7>[   35.035313] usb usb2: bus suspend, wakeup 0
<7>[   35.035315] ehci_hcd 0000:00:1d.0: suspend root hub
<6>[   35.250017] PM: suspend of devices complete after 216.979 msecs
<6>[   35.250822] PM: late suspend of devices complete after 0.799 msecs
<7>[   35.252343] ehci_hcd 0000:00:1d.0: wakeup: 1
<7>[   35.262923] ehci_hcd 0000:00:1d.0: --> PCI D3hot
<7>[   35.263302] ehci_hcd 0000:00:1a.0: wakeup: 1
<7>[   35.273912] ehci_hcd 0000:00:1a.0: --> PCI D3hot
<6>[   35.274254] PM: noirq suspend of devices complete after 23.442 msecs
<6>[   35.274975] ACPI: Preparing to enter system sleep state S3
<6>[   35.292666] PM: Saving platform NVS memory
<7>[   35.295030] Disabling non-boot CPUs ...
<6>[   35.297351] CPU 1 is now offline
<6>[   35.300345] CPU 2 is now offline
<6>[   35.303929] CPU 3 is now offline
<7>[   35.303931] lockdep: fixing up alternatives.
<6>[   35.304825] Extended CMOS year: 2000

When the device will resume the EHCI driver will get stuck in
ehci_endpoint_disable waiting for the tt_clearing flag to reset:

<0>[   47.610967] usb 2-1.3: **** DPM device timeout ****
<7>[   47.610972]  f2f11c60 00000092 f2f11c0c c10624a5 00000003 f4c6e880 c1c8a4c0 c1c8a4c0
<7>[   47.610983]  15c55698 0000000b f56b34c0 f2a45b70 f4c6e880 00000082 f2a4602c f2f11c30
<7>[   47.610993]  c10787f8 f4cac000 f2a45b70 00000000 f4cac010 f2f11c58 00000046 00000001
<7>[   47.611004] Call Trace:
<7>[   47.611006]  [<c10624a5>] ? sched_clock_cpu+0xf5/0x160
<7>[   47.611019]  [<c10787f8>] ? lock_release_holdtime.part.22+0x88/0xf0
<7>[   47.611026]  [<c103ed46>] ? lock_timer_base.isra.35+0x26/0x50
<7>[   47.611034]  [<c17592d3>] ? schedule_timeout+0x133/0x290
<7>[   47.611044]  [<c175b43e>] schedule+0x1e/0x50
<7>[   47.611051]  [<c17592d8>] schedule_timeout+0x138/0x290
<7>[   47.611057]  [<c10624a5>] ? sched_clock_cpu+0xf5/0x160
<7>[   47.611063]  [<c103e560>] ? usleep_range+0x40/0x40
<7>[   47.611070]  [<c1759445>] schedule_timeout_uninterruptible+0x15/0x20
<7>[   47.611077]  [<c14935f4>] ehci_endpoint_disable+0x64/0x160
<7>[   47.611084]  [<c147d1ee>] ? usb_hcd_flush_endpoint+0x10e/0x1d0
<7>[   47.611092]  [<c1165663>] ? sysfs_add_file+0x13/0x20
<7>[   47.611100]  [<c147d5a9>] usb_hcd_disable_endpoint+0x29/0x40
<7>[   47.611107]  [<c147fafc>] usb_disable_endpoint+0x5c/0x80
<7>[   47.611111]  [<c147fb57>] usb_disable_interface+0x37/0x50
<7>[   47.611116]  [<c1477650>] usb_reset_and_verify_device+0x4b0/0x640
<7>[   47.611122]  [<c1474665>] ? hub_port_status+0xb5/0x100
<7>[   47.611129]  [<c147a975>] usb_port_resume+0xd5/0x220
<7>[   47.611136]  [<c148877f>] generic_resume+0xf/0x30
<7>[   47.611142]  [<c14821a3>] usb_resume+0x133/0x180
<7>[   47.611147]  [<c1473b10>] ? usb_dev_thaw+0x10/0x10
<7>[   47.611152]  [<c1473b1d>] usb_dev_resume+0xd/0x10
<7>[   47.611157]  [<c13baa60>] dpm_run_callback+0x40/0xb0
<7>[   47.611164]  [<c13bdb03>] ? pm_runtime_enable+0x43/0x70
<7>[   47.611171]  [<c13bafc6>] device_resume+0x1a6/0x2c0
<7>[   47.611177]  [<c13ba940>] ? dpm_show_time+0xe0/0xe0
<7>[   47.611183]  [<c13bb0f9>] async_resume+0x19/0x40
<7>[   47.611189]  [<c10580c4>] async_run_entry_fn+0x64/0x160
<7>[   47.611196]  [<c104a244>] ? process_one_work+0x104/0x480
<7>[   47.611203]  [<c104a24c>] ? process_one_work+0x10c/0x480
<7>[   47.611209]  [<c104a2c0>] process_one_work+0x180/0x480
<7>[   47.611215]  [<c104a244>] ? process_one_work+0x104/0x480
<7>[   47.611220]  [<c1058060>] ? async_schedule+0x10/0x10
<7>[   47.611226]  [<c104c15c>] worker_thread+0x11c/0x2f0
<7>[   47.611233]  [<c104c040>] ? manage_workers.isra.27+0x1f0/0x1f0
<7>[   47.611239]  [<c10507f8>] kthread+0x78/0x80
<7>[   47.611244]  [<c1750000>] ? timer_cpu_notify+0xd6/0x20d
<7>[   47.611253]  [<c1050780>] ? __init_kthread_worker+0x60/0x60
<7>[   47.611258]  [<c176357e>] kernel_thread_helper+0x6/0xd
<7>[   47.611283] ------------[ cut here ]------------

This patch changes hub_quiesce behavior to flush the TT clear work
instead of canceling it, to make sure that no TT clear request remains
uncompleted before suspend.
Signed-off-by: NOctavian Purdila <octavian.purdila@intel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1611) updates the USB documentation and kerneldoc to
give a more precise meaning for the URB_ISO_ASAP flag and to explain
more of the details of scheduling for isochronous URBs.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The handling of large output bulk transfers is broken; the same user
page is read over and over again. Fixed with this patch.

Cc: stable <stable@vger.kernel.org>
Acked-by: NPeter Stuge <peter@stuge.se>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

SEL and PEL are in microseconds, not milliseconds.  Also, fix a split
string that will trigger checkpatch warnings.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

The Set SEL control transfer tells a device the exit latencies
associated with a device-initated U1 or U2 exit.  Since a parent hub may
initiate a transition to U1 soon after a downstream port's U1 timeout is
set, we need to make sure the device receives the Set SEL transfer
before the parent hub timeout is set.

This patch should be backported to kernels as old as 3.5, that contain
the commit 1ea7e0e8 "USB: Add support to
enable/disable USB3 link states."
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

Some USB 3.0 devices signal that they don't implement Link PM by having
all zeroes in the U1/U2 exit latencies in their SuperSpeed BOS
descriptor.  Don found that a Western Digital device he has experiences
transfer errors when LPM is enabled.  The lsusb shows the U1/U2 exit
latencies are set to zero:

Binary Object Store Descriptor:
  bLength                 5
  bDescriptorType        15
  wTotalLength           22
  bNumDeviceCaps          2
  SuperSpeed USB Device Capability:
    bLength                10
    bDescriptorType        16
    bDevCapabilityType      3
    bmAttributes         0x00
      Latency Tolerance Messages (LTM) Supported
    wSpeedsSupported   0x000e
      Device can operate at Full Speed (12Mbps)
      Device can operate at High Speed (480Mbps)
      Device can operate at SuperSpeed (5Gbps)
    bFunctionalitySupport   1
      Lowest fully-functional device speed is Full Speed (12Mbps)
    bU1DevExitLat           0 micro seconds
    bU2DevExitLat           0 micro seconds

The fix is to not enable LPM for a particular link state if we find its
corresponding exit latency is zero.

This patch should be backported to kernels as old as 3.5, that contain
the commit 1ea7e0e8 "USB: Add support to
enable/disable USB3 link states."
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: NDon Zickus <dzickus@redhat.com>
Tested-by: NDon Zickus <dzickus@redhat.com>
Cc: stable@vger.kernel.org

Before a driver is probed, we want to disable USB 3.0 Link Power
Management (LPM), in case the driver needs hub-initiated LPM disabled.
After the probe finishes, we want to attempt to re-enable LPM, order to
balance the LPM ref count.

When a probe fails (such as when libusual doesn't want to bind to a USB
3.0 mass storage device), make sure to balance the LPM ref counts by
re-enabling LPM.

This patch should be backported to kernels as old as 3.5, that contain
the commit 8306095f "USB: Disable USB
3.0 LPM in critical sections."
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

This patch (as1607) fixes a race that can occur if a USB host
controller is removed while a process is reading the
/sys/kernel/debug/usb/devices file.

The usb_device_read() routine uses the bus->root_hub pointer to
determine whether or not the root hub is registered.  The is not a
valid test, because the pointer is set before the root hub gets
registered and remains set even after the root hub is unregistered and
deallocated.  As a result, usb_device_read() or usb_device_dump() can
access freed memory, causing an oops.

The patch changes the test to use the hcd->rh_registered flag, which
does get set and cleared at the appropriate times.  It also makes sure
to hold the usb_bus_list_lock mutex while setting the flag, so that
usb_device_read() will become aware of new root hubs as soon as they
are registered.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-by: NDon Zickus <dzickus@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1607) fixes a race that can occur if a USB host
controller is removed while a process is reading the
/sys/kernel/debug/usb/devices file.

The usb_device_read() routine uses the bus->root_hub pointer to
determine whether or not the root hub is registered.  The is not a
valid test, because the pointer is set before the root hub gets
registered and remains set even after the root hub is unregistered and
deallocated.  As a result, usb_device_read() or usb_device_dump() can
access freed memory, causing an oops.

The patch changes the test to use the hcd->rh_registered flag, which
does get set and cleared at the appropriate times.  It also makes sure
to hold the usb_bus_list_lock mutex while setting the flag, so that
usb_device_read() will become aware of new root hubs as soon as they
are registered.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-by: NDon Zickus <dzickus@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit ca9c9d0c.

Rafael wants more time to work on the user api to handle port power
issues, so let's just revert the sysfs changes for now.
Reported-by: NRafael J. Wysocki <rjw@sisk.pl>
Cc: Lan Tianyu <tianyu.lan@intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>