Add support for revision 2 of the DViCO FusionHDTV DVB-T Dual Digital 4
which has new tuners and demodulators (2 x DIB7070p). With this patch
both DVB reception and IR works.

The dib7000p driver currently hardwires the output mode to
OUTMODE_MPEG2_SERIAL regardless of what we ask for. Modify it to allow
OUTMODE_MPEG2_PAR_GATED_CLK to be set. Longer term we should remove the
check completely and set the output mode correctly in all the callers.

Add Kconfig bits to ensure the dib7000p and dib0070 modules are enabled.
It would be nice to only do this for the !DVB_FE_CUSTOMISE case, but
this is what the other DIB7070 module does (there are a number of
module dependencies in the attach code).
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This adds basic support for the Hauppauge Nova-TD-500 84xxx series.

A future patch will allow for one aerial input to supply both tuners.

With the current code, an aerial must be plugged into each antannae input
in order for both tuners to function.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This comment helps to make the code more readable.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fixed a lot of sparse warnings: mostly warnings about shadowed variables
and signed/unsigned mismatches.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

quoting Robert Lowery:

I think I've found the cause of the oops.
[...]
BTW it appears I have fixed my tuning problems with the updated patch
below.  This reverts a change Mauro made a while back.

All is good now  :)
[...]
The good news is that I've got a better patch that definitely works this
time and even better, makes use of the standard firmware (rather than
the Australian specific one).

...based on an earlier patch by Hans-Frieder Vogt:
http://www.linuxtv.org/pipermail/linux-dvb/2008-May/026280.htmlSigned-off-by: NRobert Lowery <rlowery@exemail.com.au>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

After commit d9b19199
(always enable FW_LOADER unless EMBEDDED=y) we can remove
the FW_LOADER select's and corresponding dependencies
on HOTPLUG.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch makes the needlessly global struct anysee_usb_mutex static.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NIgor M Liplianin <liplianin@me.by>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Also remove some blank lines that were used to split compat code at -devel
tree.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

After adding support for AVerTVHD Volar, DVB_USB_CXUSB must
select MEDIA_TUNER_MXL5005S if !DVB_FE_CUSTOMISE
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Add initial support for this device. The AGC and tracking filter
settings for the mxl5003 are known to be wrong, but it generally works.
Signed-off-by: NDaniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Add missing auto-selects for MEDIA_TUNER_XC2028 and DVB_TDA1004X at
dvb-usb/Kconfig.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

$ find linux/drivers/media/dvb -exec grep -l tda827x_attach '{}' \;
linux/drivers/media/dvb/dvb-usb/m920x.c
linux/drivers/media/dvb/ttpci/budget-ci.c
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- select DVB_PLL
- fix typos in comments
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- support for Anysee E30C Plus rev 0.4
 - set IO port E
 - set correct TS mode
- change deltaf according to latest Windows driver
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- coding style fixes raised by checkpatch
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- update license comments
- change MODULE_DESCRIPTION from device specific to chipset specific
- correct debug switch from deb_rc to deb_info
- correct MPEG2 stream interval from 1.25 to 1
- change frontend_attach error code from -EIO to -ENODEV
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- remove useless identify_state - device is always warm
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- coding style fixes raised by checkpatch
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- driver for Anysee DVB-T/C receiver
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

...which means allocating our own copy when we want to modify it.

(stupid thinko fixed by mkrufky)
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>

In the umt-010 driver the struct umt_properties sets the number of URBs for
transfer to 20.  But in dvb-usb.h MAX_NO_URBS_FOR_DATA_STREAM is set to 10.

Not surprisingly this causes an oops for all devices which use the umt-010
chipset when they are inserted.

fix on Kaffeine channel scan for

Initialize stream count using MAX_NO_URBS_FOR_DATA_STREAM.
Signed-off-by: NTim Gardner <tim.gardner@canonical.com>
Signed-off-by: Nmaximilian attems <max@stro.at>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- change msleep(0) to msleep(1)
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- remove useless identify_state - device is always warm
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- add little sleep to avoid I2C errors arising on faster CPUs
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

testing of the -tip tree found the following build failures on
2.6.26-rc3:

  drivers/built-in.o: In function `ttusb_dec_disconnect':
  ttusb_dec.c:(.text+0xa2c95): undefined reference to `input_unregister_device'

  drivers/built-in.o: In function `dvb_usb_read_remote_control':
  dvb-usb-remote.c:(.text+0xa6a94): undefined reference to `input_event'

with this config:

  http://redhat.com/~mingo/misc/config-Tue_May_20_03_48_57_CEST_2008.bad

these are due to the media/dvb/usb layer having dependencies on INPUT
functionality, without having that spelled out in the Kconfig file.

this patch makes that dependency explicit (for the drivers affected),
which solves the build error.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Since:
1) FW_LOADER is defined as:

config FW_LOADER
        tristate "Userspace firmware loading support"
        depends on HOTPLUG

2) several V4L/DVB driver just selects it;

3) select is not smart enough to auto-select HOTPLUG, if select FW_LOADER.

So, All drivers that select FW_LOADER should also depend on HOTPLUG.

An easier solution (for the end-user perspective) would be to "select HOTPLUG".
However, live is not simple. This would cause recursive dependency issues like
this one:

drivers/usb/Kconfig:62:error: found recursive dependency: USB -> USB_OHCI_HCD
-> I2C -> MEDIA_TUNER -> MEDIA_TUNER_XC2028 -> HOTPLUG -> PCCARD -> PCMCIA ->
USB_ARCH_HAS_HCD -> MOUSE_APPLETOUCH -> USB
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

namespace for all of them.

There were several issues in the past, caused by the hybrid tuner design, since
now, the same tuner can be used by drivers/media/dvb and drivers/media/video.

Kconfig items were rearranged, to split V4L/DVB core from their drivers.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fixed some typos.
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Some DVB-S boards, i.e. with the SD1878 tuner, use a 4 MHz reference frequency.
This reqires a different setup of the clock PLL.
This patch adds an enum to the tda10086_config struct and sets the proper
values for the boards.

This patch also fixes the DVB-S section of the MD7134_BRIDGE_2
Signed-off-by: NHartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch fixes several issues on SCODE:

1) The extracting tool weren't generating the proper tags for SCODE. This
   has almost no effect, since those tags shouldn't be used;

2) DIBCOM52 were using a wrong IF. It should be 5200, instead of 5700;

3) seek_firmware were wanting an exact match for firmware type. This is
   wrong. As result, no SCODE firmware were loaded;

4) A few files were including the wrong file for seeking demod firmwares;

5) XC3028_FE_DEFAULT can be used, if user doesn't want to load a firmware.
   However, this weren't documentated. This feature require more testing.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>