The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.

CC: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

CONFIG_HOTPLUG is going away as an option.  As a result, the __dev*
markings need to be removed.

This change removes the use of __devinit, __devexit_p, __devinitdata,
and __devexit from these drivers.

Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.

Cc: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix build failure if building a monolithic kernel due to
arch/mips/kernel/Kconfig selecting MODULES_USE_ELF_REL[A] without checking
to see if MODULES is set or not.  This leads to 'struct module' not
existing, which triggers a compile failure in arch/mips/kernel/module-rela.c
when the compiler attempts to dereference me->name:

  CC      arch/mips/kernel/module-rela.o
arch/mips/kernel/module-rela.c: In function ‘apply_r_mips_26_rela’:
arch/mips/kernel/module-rela.c:38:74: error: dereferencing pointer to incomplete type
arch/mips/kernel/module-rela.c:46:12: error: dereferencing pointer to incomplete type
arch/mips/kernel/module-rela.c: In function ‘apply_relocate_add’:
arch/mips/kernel/module-rela.c:133:13: error: dereferencing pointer to incomplete type
make[2]: *** [arch/mips/kernel/module-rela.o] Error 1
Signed-off-by: NJoshua Kinard <kumba@gentoo.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4749/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

ERROR: "min_low_pfn" [drivers/block/aoe/aoe.ko] undefined!

Fixed by moving the implementation of virt_addr_valid() into the kernel
proper and exporting it which removes the pains of an inline or macro
implementation.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

So far we're jumping through hoops to keep the file usable from assembler
source but it's getting just too painful.  Turns out that many uses of
<asm/page.h> are unnecessary anyway, so just remove those.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The value is incorrect and were copied in Linux 2.5.4 from i386.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This reverts commit ff401e52.

This breaks on MIPS64 R2 cores such as Broadcom's.

Commit 4be3d2f3 ("MIPS: perf: Add XLP
support for hardware perf.") added UNSUPPORTED_PERF_EVENT_ID which was
removed a while back.

Cc: Zi Shen Lim <zlim@netlogicmicro.com>
Cc: Jayachandran C <jchandra@broadcom.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: Zi Shen Lim <zlim@netlogicmicro.com>
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Acked-by: NJayachandran C <jchandra@broadcom.com>
Patchwork: https://patchwork.linux-mips.org/patch/4730/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Now that the r4k timer is registered no matter what, bump the rating of
the Alchemy 32kHz timer so that it gets used when it is working,
and fall back on the r4k when it isn't.

This fixes a timer-related hang on platform with a working 32kHz timer
(the better rated c0 timer stops while executing 'wait' leading to (almost)
eternal sleep) and an oops on boot on platforms without a working 32kHz
timer (due to double registration of the r4k timer).
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Cc:  Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/4728/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

for the architectures that have usp in pt_regs and do not have
user_stack_pointer() already defined.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

All architectures have
	CONFIG_GENERIC_KERNEL_THREAD
	CONFIG_GENERIC_KERNEL_EXECVE
	__ARCH_WANT_SYS_EXECVE
None of them have __ARCH_WANT_KERNEL_EXECVE and there are only two callers
of kernel_execve() (which is a trivial wrapper for do_execve() now) left.
Kill the conditionals and make both callers use do_execve().
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Nobody seems to be interested anymore and upstream also never had an
ethernet driver.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

  CC      arch/mips/wrppmc/pci.o
/home/ralf/src/linux/linux-mips/arch/mips/wrppmc/pci.c: In function ‘gt64120_pci_init’:
/home/ralf/src/linux/linux-mips/arch/mips/wrppmc/pci.c:41:6: error: variable ‘tmp’ set but not used [-Werror=unused-but-set-variable]
cc1: all warnings being treated as errors

This warning exists in gcc 4.6.0 and newer.  Kernels 2.6.40 and newer use
-Wunused-but-set-variable to suppress it.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

  CC      arch/mips/sgi-ip22/ip22-eisa.o
/home/ralf/src/linux/linux-mips/arch/mips/sgi-ip22/ip22-eisa.c: In function ‘ip22_eisa_intr’:
/home/ralf/src/linux/linux-mips/arch/mips/sgi-ip22/ip22-eisa.c:77:11: error: variable ‘dma2’ set but not used [-Werror=unused-but-set-variable]
/home/ralf/src/linux/linux-mips/arch/mips/sgi-ip22/ip22-eisa.c:77:5: error: variable ‘dma1’ set but not used [-Werror=unused-but-set-variable]
cc1: all warnings being treated as errors

This warning exists in gcc 4.6.0 and newer.  Kernels 2.6.40 and newer use
-Wunused-but-set-variable to suppress it.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

  CC      arch/mips/rb532/prom.o
/home/ralf/src/linux/linux-mips/arch/mips/rb532/prom.c: In function ‘prom_setup_cmdline’:
/home/ralf/src/linux/linux-mips/arch/mips/rb532/prom.c:75:22: error: variable ‘prom_envp’ set but not used [-Werror=unused-but-set-variable]

This warning exists in gcc 4.6.0 and newer.  Kernels 2.6.40 and newer use
-Wunused-but-set-variable to suppress it.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

  CC      arch/mips/powertv/init.o
/home/ralf/src/linux/linux-mips/arch/mips/powertv/init.c: In function ‘mips_nmi_setup’:
/home/ralf/src/linux/linux-mips/arch/mips/powertv/init.c:80:8: error: variable ‘base’ set but not used [-Werror=unused-but-set-variable]
/home/ralf/src/linux/linux-mips/arch/mips/powertv/init.c: In function ‘mips_ejtag_setup’:
/home/ralf/src/linux/linux-mips/arch/mips/powertv/init.c:94:8: error: variable ‘base’ set but not used [-Werror=unused-but-set-variable]
cc1: all warnings being treated as errors

As these two functions are, they don't serve any useful purpose so I've
deleted them entirely.

This warning exists in gcc 4.6.0 and newer.  Kernels 2.6.40 and newer use
-Wunused-but-set-variable to suppress it.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

I had no idea just how broken IOC3 was until I read this.
Signed-off-by: NDave Jones <davej@redhat.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

  CC      arch/mips/mm/highmem.o
/home/ralf/src/linux/linux-mips/arch/mips/mm/highmem.c: In function ‘__kunmap_atomic’:
/home/ralf/src/linux/linux-mips/arch/mips/mm/highmem.c:70:6: error: variable ‘type’ set but not used [-Werror=unused-but-set-variable]
cc1: all warnings being treated as errors

This warning exists in gcc 4.6.0 and newer.  Kernels 2.6.40 and newer use
-Wunused-but-set-variable to suppress it.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Normally r4k_dma_cache_inv should only ever be called with cacheline
aligned addresses.  If however, it isn't there is the theoretical
possibility of data corruption.  There is no correct way of handling this
and anyway, it should only happen if the DMA API is used incorrectly
so drop

There is a different corruption scenario with these CACHE instructions
removed but again there is no way of handling this correctly and it can
be triggered only through incorrect use of the DMA API.

So just get rid of the complexity.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Reported-by: NJames Rodriguez <jamesr@juniper.net>

The default implementation of 'cpu_has_fpu' macro calls
smp_processor_id() which causes this warning to be printed when
preemption is enabled:

[    4.664000] Algorithmics/MIPS FPU Emulator v1.5
[    4.676000] BUG: using smp_processor_id() in preemptible [00000000] code: ini
[    4.700000] caller is fpu_emulator_cop1Handler+0x434/0x27b8

This problem got introduced in November 2009 by
af1d2af877ef6c36990671bc86a5b9c5bb50b1da (lmo) [MIPS: Fix emulation of
64-bit FPU on 64-bit CPUs.] rsp.  da0bac33
(kernel.org) [MIPS: Fix emulation of 64-bit FPU on FPU-less 64-bit CPUs.]
in 2.6.32.

Fixed by rewriting cop1_64bit() to return a constant whenever possible
but most importantly avoid the use pf cpu_has_fpu entirely.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Reported-by: NJayachandran C <jchandra@broadcom.com>
Initial-patch-by: NJayachandran C <jchandra@broadcom.com>
Patchwork: https://patchwork.linux-mips.org/patch/4225/

 Our FP emulator is hardcoded for the MIPS IV FP instruction set and does
not match the FP ISA with the general ISA.  However for the few MIPS IV FP
instructions that use the COP1X major opcode it relies on the Coprocessor
Unusable exception to be delivered as a COP1 rather than COP3 exception.
This includes indexed transfer (LDXC1, etc.) and FP multiply-accumulate
(MADD.D, etc.) instructions.

 All the MIPS I, II, III and IV processors and some newer chips that do not
implement the FPU use the COP3 exception however.  Therefore I believe the
kernel should follow and redirect any COP3 Unusable traps to the emulator
unless an actual FPU part or core is present.

 This is a change that implements it.  Any minor opcode encodings that are
not recognised as valid FP instructions are rejected by the emulator and
will result in a SIGILL signal being delivered as they currently do.  We
do not support vendor-specific coprocessor 3 implementations supported
with MIPS I and MIPS II ISA processors; we never set CP0.Status.CU3.

[Ralf: On MIPS IV processors the kernel always enables the XX bit which
replaces the CU3 bit off earlier architecture revisions.]

 If matching between the CPU and the FPU ISA is considered required one
day, this can still be done in the emulator itself.  I think the CpU
exception dispatcher is not the right place to do this anyway, as there
are further differences between MIPS I, MIPS II, MIPS III, MIPS IV and
MIPS32 FP ISAs.

 Corresponding explanation of this implementation is included within the
change itself.
Signed-off-by: NMaciej W. Rozycki <macro@codesourcery.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/project/linux-mips/list/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

When poweroff machine, kernel_power_off() call disable_nonboot_cpus().
And if we have HOTPLUG_CPU configured, disable_nonboot_cpus() is not an
empty function but attempt to actually disable the nonboot cpus. Since
system state is SYSTEM_POWER_OFF, play_dead() won't be called and thus
disable_nonboot_cpus() hangs. Therefore, we make this patch to avoid
poweroff failure.
Signed-off-by: NHuacai Chen <chenhc@lemote.com>
Signed-off-by: NHongliang Tao <taohl@lemote.com>
Signed-off-by: NHua Yan <yanh@lemote.com>
Cc: Yong Zhang <yong.zhang@windriver.com>
Cc: stable@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/4211/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

When CONFIG_UIDGID_STRICT_TYPE_CHECKS is enabled, plain integer checking
between different uids/gids is explicitely turned into a build failure
by making the k{uid,gid}_t types a structure containing a value:

arch/mips/kernel/mips-mt-fpaff.c: In function 'check_same_owner':
arch/mips/kernel/mips-mt-fpaff.c:53:22: error: invalid operands to
binary == (have 'kuid_t' and 'kuid_t')
arch/mips/kernel/mips-mt-fpaff.c:54:15: error: invalid operands to
binary == (have 'kuid_t' and 'kuid_t')

In order to ensure proper comparison between uids, using the helper
function uid_eq() which performs the right thing whenever this config
option is turned on or off.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Patchwork: https://patchwork.linux-mips.org/patch/4717/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This header was added in commit 39b8d525
(kernel.org) / b6e90cd0ae7a556080d9ea2ec1b8f6d9accad9d4 (lmo( ([MIPS] Add
support for MIPS CMP platform.).  None of the functions it declared were
ever included in the tree. Commit cb7f39d2
(kernel.org) / b6e90cd0ae7a556080d9ea2ec1b8f6d9accad9d4 (lmo) [MIPS] Remove
unused maltasmp.h.] removeed the sole file that included it because that
file was itself unused.

[ralf@linux-mips.org: The whole mess happened because somebody at MIPS
thought it was a good idea to rename VSMP ("Vitual SMP") to SMVP.  Which
is an IBMeque ETLA in contrast to VSMP, so public kernels as opposed to
MTI's inhouse kernels never followed suit.]
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/3950/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Some initialization errors are reported with the existing OCTEON EDAC
support patch.  Also some parts have more than one memory controller.

Fix the errors and add multiple controllers if present.
Signed-off-by: NDavid Daney <david.daney@cavium.com>

Signed-off-by: NDavid Daney <david.daney@cavium.com>

Used by follow-on EDAC patches.
Signed-off-by: NDavid Daney <david.daney@cavium.com>

The patch needs to eliminate the definition of OCTEON_IRQ_BOOTDMA so
that the device tree code can map the interrupt, so in order to not
temporarily break things, we do a single patch to both the interrupt
registration code and the pata_octeon_cf driver.

Also rolled in is a conversion to use hrtimers and corrections to the
timing calculations.
Acked-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NDavid Daney <david.daney@cavium.com>

Manuel Lauss <manuel.lauss@gmail.com> writes:

I introduced it as a fallback because early revisions of Alchemy hardware
we shipped had a non-functional 32kHz timer and had to rely on the r4k
timer instead.  Previously the r4k timer was initialized regardless, but
it's useless with the "wait" instruction.

So long story short:   I need either the on-chip 32kHz timer OR the r4k
timer if the 32kHz one is unusable, but not both, and r4k timer is useless
when au1k_idle is in use.

The current in-kernel Alchemy boards all work with the 32kHz timer, so I'm
not against removing R4K_LIB symbols.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Manuel Lauss <manuel.lauss@gmail.com> writes:

I introduced it as a fallback because early revisions of Alchemy hardware
we shipped had a non-functional 32kHz timer and had to rely on the r4k
timer instead.  Previously the r4k timer was initialized regardless, but
it's useless with the "wait" instruction.

So long story short:   I need either the on-chip 32kHz timer OR the r4k
timer if the 32kHz one is unusable, but not both, and r4k timer is useless
when au1k_idle is in use.

The current in-kernel Alchemy boards all work with the 32kHz timer, so I'm
not against removing R4K_LIB symbols.
Signed-off-by: NSteven J. Hill <sjhill@mips.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch changes the physmap-flash platform data on AR7 to pass the
correct partition parser: ar7part to used by the "physmap-flash" mapping
driver so we get the partitions probed correctly.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Cc: blogic@openwrt.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4654/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Correct spelling typo ENDIANESS to ENDIANNESS in arc/mips/lantiq/xway/dma.c
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Cc: trivial@kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/4613/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

With the upcoming merge of the ARC architecture there is a small likelyhood
of conflicting use for the CONFIG_ARC config symbol.  Rename it to
CONFIG_FW_ARC.  Also rename CONFIG_ARC32 to CONFIG_FW_ARC32, CONFIG_ARC64
to CONFIG_FW_ARC64.

For consistence also rename CONFIG_SNIPROM to CONFIG_FW_SNIPROM and
CONFIG_CFE to CONFIG_FW_CFE.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

[ralf@linux-mips.org: Original patch by Maxim Uvarov <muvarov@gmail.com>
with plenty of further shining, polishing, debugging and testing by me.]
Signed-off-by: NMaxim Uvarov <muvarov@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: kexec@lists.infradead.org
Cc: horms@verge.net.au
Patchwork: https://patchwork.linux-mips.org/patch/1026/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

[ralf@linux-mips.org: Original patch by Maxim Uvarov <muvarov@gmail.com>
with plenty of further shining, polishing, debugging and testing by me.]
Signed-off-by: NMaxim Uvarov <muvarov@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: kexec@lists.infradead.org
Cc: horms@verge.net.au
Patchwork: https://patchwork.linux-mips.org/patch/1025/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>