Change the default mapping between TC and TCG as follows:

Prio     |             TC/TCG
         |      from             to
         |    (set by FW)      (set by SW)
---------+-----------------------------------
0        |      0/0              0/7
1        |      1/0              0/6
2        |      2/0              0/5
3        |      3/0              0/4
4        |      4/0              0/3
5        |      5/0              0/2
6        |      6/0              0/1
7        |      7/0              0/0

These new settings cause that a pause frame for any prio stops
traffic for all prios.

Fixes: 564c274c ("net/mlx4_en: DCB QoS support")
Signed-off-by: NMoni Shoua <monis@mellanox.com>
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove redundant and not essential operations in fmr unmap/free.
According to device spec, in FMR unmap it is sufficient to set
ownership bit to SW. This allows remapping afterwards.

Fixes: 8ad11fb6 ("IB/mlx4: Implement FMRs")
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NMoshe Shemesh <moshe@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use early goto commands, and save else branches.
This uses less indentations and brackets, making the code
more readable.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do not check IPv6 bit in cqe status if CONFIG_IPV6 is not enabled.
Function check_csum() is reached only with IPv4 or IPv6 set (if enabled),
if IPv6 is not set (or is not enabled) it is redundant to test the
IPv4 bit.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During unload, on mlx5_stop_eqs we move command interface from events
mode to polling mode, but if command interface EQ destroy fail we move
back to events mode.
That's wrong since even if we fail to destroy command interface EQ, we
do release its irq, so no interrupts will be received.

Fixes: e126ba97 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: NMoshe Shemesh <moshe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

When mlx5_stop_eqs fails to destroy any of the eqs it returns with an error.
In such failure flow the function will return without
releasing all EQs irqs and then pci_free_irq_vectors will fail.
Fix by only warn on destroy EQ failure and continue to release other
EQs and their irqs.

It fixes the following kernel trace:
kernel: kernel BUG at drivers/pci/msi.c:352!
...
...
kernel: Call Trace:
kernel: pci_disable_msix+0xd3/0x100
kernel: pci_free_irq_vectors+0xe/0x20
kernel: mlx5_load_one.isra.17+0x9f5/0xec0 [mlx5_core]

Fixes: e126ba97 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: NMoshe Shemesh <moshe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Flow steering priority and namespace are software only objects that
didn't have the proper destructors and were not freed during steering
cleanup.

Fix it by adding destructor functions for these objects.

Fixes: bd71b08e ("net/mlx5: Support multiple updates of steering rules in parallel")
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

When calling add/remove VXLAN port, a lock must be held in order to
prevent race scenarios when more than one add/remove happens at the
same time.
Fix by holding our state_lock (mutex) as done by all other parts of the
driver.
Note that the spinlock protecting the radix-tree is still needed in
order to synchronize radix-tree access from softirq context.

Fixes: b3f63c3d ("net/mlx5e: Add netdev support for VXLAN tunneling")
Signed-off-by: NGal Pressman <galp@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

A refcount mechanism must be implemented in order to prevent unwanted
scenarios such as:
- Open an IPv4 VXLAN interface
- Open an IPv6 VXLAN interface (different socket)
- Remove one of the interfaces

With current implementation, the UDP port will be removed from our VXLAN
database and turn off the offloads for the other interface, which is
still active.
The reference count mechanism will only allow UDP port removals once all
consumers are gone.

Fixes: b3f63c3d ("net/mlx5e: Add netdev support for VXLAN tunneling")
Signed-off-by: NGal Pressman <galp@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

mlx5e_vxlan_lookup_port is called both from mlx5e_add_vxlan_port (user
context) and mlx5e_features_check (softirq), but the lock acquired does
not disable bottom half and might result in deadlock. Fix it by simply
replacing spin_lock() with spin_lock_bh().
While at it, replace all unnecessary spin_lock_irq() to spin_lock_bh().

lockdep's WARNING: inconsistent lock state
[  654.028136] inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
[  654.028229] swapper/5/0 [HC0[0]:SC1[9]:HE1:SE0] takes:
[  654.028321]  (&(&vxlan_db->lock)->rlock){+.?.}, at: [<ffffffffa06e7f0e>] mlx5e_vxlan_lookup_port+0x1e/0x50 [mlx5_core]
[  654.028528] {SOFTIRQ-ON-W} state was registered at:
[  654.028607]   _raw_spin_lock+0x3c/0x70
[  654.028689]   mlx5e_vxlan_lookup_port+0x1e/0x50 [mlx5_core]
[  654.028794]   mlx5e_vxlan_add_port+0x2e/0x120 [mlx5_core]
[  654.028878]   process_one_work+0x1e9/0x640
[  654.028942]   worker_thread+0x4a/0x3f0
[  654.029002]   kthread+0x141/0x180
[  654.029056]   ret_from_fork+0x24/0x30
[  654.029114] irq event stamp: 579088
[  654.029174] hardirqs last  enabled at (579088): [<ffffffff818f475a>] ip6_finish_output2+0x49a/0x8c0
[  654.029309] hardirqs last disabled at (579087): [<ffffffff818f470e>] ip6_finish_output2+0x44e/0x8c0
[  654.029446] softirqs last  enabled at (579030): [<ffffffff810b3b3d>] irq_enter+0x6d/0x80
[  654.029567] softirqs last disabled at (579031): [<ffffffff810b3c05>] irq_exit+0xb5/0xc0
[  654.029684] other info that might help us debug this:
[  654.029781]  Possible unsafe locking scenario:

[  654.029868]        CPU0
[  654.029908]        ----
[  654.029947]   lock(&(&vxlan_db->lock)->rlock);
[  654.030045]   <Interrupt>
[  654.030090]     lock(&(&vxlan_db->lock)->rlock);
[  654.030162]
 *** DEADLOCK ***

Fixes: b3f63c3d ("net/mlx5e: Add netdev support for VXLAN tunneling")
Signed-off-by: NGal Pressman <galp@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

In error flow, when DESTROY_QP command should be executed, the wrong
mailbox was set with data, not the one that is written to hardware,
Fix that.

Fixes: 09a7d9ec '{net,IB}/mlx5: QP/XRCD commands via mlx5 ifc'
Signed-off-by: NMoni Shoua <monis@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Fix misspelling in word syndrome.

Fixes: e126ba97 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Fixes the bug when turning on/off CQE compression mechanism
resets the RX rings size to default value when it is not
needed.

Fixes: 2fc4bfb7 ("net/mlx5e: Dynamic RQ type infrastructure")
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

The assumption that the next header field contains the transport
protocol is wrong for IPv6 packets with extension headers.
Instead, we should look the inner-most next header field in the buffer.
This will fix TSO offload for tunnels over IPv6 with extension headers.

Performance testing: 19.25x improvement, cool!
Measuring bandwidth of 16 threads TCP traffic over IPv6 GRE tap.
CPU: Intel(R) Xeon(R) CPU E5-2660 v2 @ 2.20GHz
NIC: Mellanox Technologies MT28800 Family [ConnectX-5 Ex]
TSO: Enabled
Before: 4,926.24  Mbps
Now   : 94,827.91 Mbps

Fixes: b3f63c3d ("net/mlx5e: Add netdev support for VXLAN tunneling")
Signed-off-by: NGal Pressman <galp@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Fix bug that allows ets bw sum to be 0% when ets tc type exists.

Fixes: 08fb1dac ('net/mlx5e: Support DCBNL IEEE ETS')
Signed-off-by: NMoshe Shemesh <moshe@mellanox.com>
Reviewed-by: NHuy Nguyen <huyn@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

In mlx5_ifc, struct size was not complete, and thus driver was sending
garbage after the last defined field. Fixed it by adding reserved field
to complete the struct size.

In addition, rename all set_rate_limit to set_pp_rate_limit to be
compliant with the Firmware <-> Driver definition.

Fixes: 7486216b ("{net,IB}/mlx5: mlx5_ifc updates")
Fixes: 1466cc5b ("net/mlx5: Rate limit tables support")
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Before the offending commit, mlx5 core did the IRQ affinity itself,
and it seems that the new generic code have some drawbacks and one
of them is the lack for user ability to modify irq affinity after
the initial affinity values got assigned.

The issue is still being discussed and a solution in the new generic code
is required, until then we need to revert this patch.

This fixes the following issue:
echo <new affinity> > /proc/irq/<x>/smp_affinity
fails with  -EIO

This reverts commit a435393a.
Note: kept mlx5_get_vector_affinity in include/linux/mlx5/driver.h since
it is used in mlx5_ib driver.

Fixes: a435393a ("mlx5: move affinity hints assignments to generic code")
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jes Sorensen <jsorensen@fb.com>
Reported-by: NJes Sorensen <jsorensen@fb.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Currently, if a size of zero is passed to
mlx5_fpga_mem_{read|write}_i2c()
the "err" return value will not be initialized, which triggers gcc
warnings:

[..]/mlx5/core/fpga/sdk.c:87 mlx5_fpga_mem_read_i2c() error:
uninitialized symbol 'err'.
[..]/mlx5/core/fpga/sdk.c:115 mlx5_fpga_mem_write_i2c() error:
uninitialized symbol 'err'.

fix that.

Fixes: a9956d35 ('net/mlx5: FPGA, Add SBU infrastructure')
Signed-off-by: NKamal Heib <kamalh@mellanox.com>
Reviewed-by: NYevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

This reverts commit 63dd00fa.

RAUHT DELETE_ALL seems to trigger a bug in FW. That manifests by later
calls to RAUHT ADD of an IPv6 neighbor to fail with "bad parameter"
error code.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Fixes: 63dd00fa ("mlxsw: spectrum_router: Add batch neighbour deletion")
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Learning is currently enabled for ports which are OVS slaves -
even though OVS doesn't need this indication.
Since we're not associating a fid with the port, HW would continuously
notify driver of learned [& aged] MACs which would be logged as errors.

Fixes: 2b94e58d ("mlxsw: spectrum: Allow ports to work under OVS master")
Signed-off-by: NYuval Mintz <yuvalm@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Before this patch, the stats_lock was acquired twice. In between the
locks Driver sent command to gather some more statistics (per priority
and counter statistics). If the stats lock was acquired by get
statistics NDO in between we would have report out of sync counters.

Fix this by collecting all stats from Firmware in advance and then
fill the Software structs under one lock.

Fixes: 0b131561 ("net/mlx4_en: Add Flow control statistics display via ethtool")
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The field res_free indicates the total number of counters which are
available for allocation (reserved and unreserved). Fixed a bug where
the reserved counters were subtracted from res_free before any
allocation was performed.

Before this fix, free counters which were not reserved could not be
allocated.

Fixes: 9de92c60 ("net/mlx4_core: Adjust counter grant policy in the resource tracker")
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set the minimal MTU threshold for running loopback selftest.
MTU should be big enough to include packet payload, NET_IP_ALIGN,
Ethernet headers and preamble length.

Fixes: e7c1c2c4 ("mlx4_en: Added self diagnostics test implementation")
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, whenever the NETIF_F_HW_TC feature changes, we silently
always allow it, but we actually do not disable the flows in HW
on disable. That breaks user's expectations. So just forbid
the feature disable in case there are any filters offloaded.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tcfm_dev always points to the correct netdev and we already
hold a refcnt, so no need to use tcfm_ifindex to lookup again.

If we would support moving target netdev across netns, using
pointer would be better than ifindex.

This also fixes dumping obsolete ifindex, now after the
target device is gone we just dump 0 as ifindex.

Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since day one of XDP drivers had to remember to free the program
on the remove path.  This leads to code duplication and is error
prone.  Make the stack query the installed programs on unregister
and if something is installed, remove the program.  Freeing of
program attached to XDP generic is moved from free_netdev() as well.

Because the remove will now be called before notifiers are
invoked, BPF offload state of the program will not get destroyed
before uninstall.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Reviewed-by: NQuentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

The function mlxsw_sp_nexthop_rif_update() walks the list of nexthops
associated with a RIF, and updates the corresponding entries in the
switch. It is used in particular when a tunnel underlay netdevice moves
to a different VRF, and all the nexthops are migrated over to a new RIF.
The problem is that each nexthop holds a reference to its RIF, and that
is not updated. So after the old RIF is gone, further activity on these
nexthops (such as downing the underlay netdevice) dereferences a
dangling pointer.

Fix the issue by updating rif of impacted nexthops before calling
mlxsw_sp_nexthop_rif_update().

Fixes: 0c5f1cd5 ("mlxsw: spectrum_router: Generalize __mlxsw_sp_ipip_entry_update_tunnel()")
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some tunnels that are offloadable on their own can nonetheless be
demoted to slow path if their local address is in conflict with that of
another tunnel. When a route is formed for such a tunnel,
mlxsw_sp_nexthop_ipip_init() fails to find the corresponding IPIP entry,
and that triggers a FIB abort.

Resolve the problem by not assuming that a tunnel for which
mlxsw_sp_ipip_ops.can_offload() holds also automatically has an IPIP
entry.

Fixes: af641713 ("mlxsw: spectrum_router: Onload conflicting tunnels")
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mlxsw driver currently doesn't offload GRE tunnels if they have the
same local address and use the same underlay VRF. When such a situation
arises, the tunnels in conflict are demoted to slow path.

However, the current code only verifies this condition on tunnel
creation and tunnel change, not when a tunnel is moved to a different
VRF. When the tunnel has no bound device, underlay and overlay are the
same. Thus moving a tunnel moves the underlay as well, and that can
cause local address conflict.

So modify mlxsw_sp_netdevice_ipip_ol_vrf_event() to check if there are
any conflicting tunnels, and demote them if yes.

Fixes: af641713 ("mlxsw: spectrum_router: Onload conflicting tunnels")
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a new local route is added, an IPIP entry is looked up to determine
whether the route should be offloaded as a tunnel decap or as a trap.
That decision should take into account whether the tunnel netdevice in
question is actually IFF_UP, and only install a decap offload if it is.

Fixes: 0063587d ("mlxsw: spectrum: Support decap-only IP-in-IP tunnels")
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On some systems, when we unsplit a port we need to re-create two ports
instead. On other systems, only one needs to be re-created.

Do not try to create a port if during driver initialization it was
assigned a negative module number, which is invalid.

This avoids the following error during unsplit:
[  941.012478] mlxsw_spectrum 0000:01:00.0: Port 43: Failed to map module

The error is harmless and caused by the fact that a local port is
already mapped to module 0.

Fixes: be94535f ("mlxsw: spectrum: Make split flow match firmware requirements")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As the page free path makes no distinction between cache hot and cold
pages, there is no real useful ordering of pages in the free list that
allocation requests can take advantage of.  Juding from the users of
__GFP_COLD, it is likely that a number of them are the result of copying
other sites instead of actually measuring the impact.  Remove the
__GFP_COLD parameter which simplifies a number of paths in the page
allocator.

This is potentially controversial but bear in mind that the size of the
per-cpu pagelists versus modern cache sizes means that the whole per-cpu
list can often fit in the L3 cache.  Hence, there is only a potential
benefit for microbenchmarks that alloc/free pages in a tight loop.  It's
even worse when THP is taken into account which has little or no chance
of getting a cache-hot page as the per-cpu list is bypassed and the
zeroing of multiple pages will thrash the cache anyway.

The truncate microbenchmarks are not shown as this patch affects the
allocation path and not the free path.  A page fault microbenchmark was
tested but it showed no sigificant difference which is not surprising
given that the __GFP_COLD branches are a miniscule percentage of the
fault path.

Link: http://lkml.kernel.org/r/20171018075952.10627-9-mgorman@techsingularity.netSigned-off-by: NMel Gorman <mgorman@techsingularity.net>
Acked-by: NVlastimil Babka <vbabka@suse.cz>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In commit 4a3c67a6 ("mlxsw: spectrum_router: Don't batch neighbour
deletion") I removed the support for batch deletion of neighbours on a
router interface (RIF) since at that time the firmware did not support
it for IPv6 neighbours.

This is now supported by the version enforced by the driver, so there is
no reason to delete neighbours one by one anymore.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This new firmware contains:
 - Support Spectrum A1 revision
 - Batch deletion of IPv6 neighbours
 - Remove incorrect VPD capability
Signed-off-by: NShalom Toledo <shalomt@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since Mellanox focus is on newer adapters, we would like to have the
ability to disable the support for old gen2 adapters.

This can be done by turning off the MLX4_CORE_GEN2 Kconfig flag.
We keep it turned on by default.
Signed-off-by: NSlava Shwartsman <slavash@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is to prevent the case of working with a single MPWQE
(1 WQE is always reserved as RQ is linked-list).
When the WQE is fully consumed, HW should still have available buffer
in order not to drop packets.

Fixes: 461017cb ("net/mlx5e: Support RX multi-packet WQE (Striding RQ)")
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Currently, when dma mapping fails, put_page is called,
but the page is not set to null. Later, in the page_reuse treatment in
mlx5e_free_rx_descs(), mlx5e_page_release() is called for the second time,
improperly doing dma_unmap (for a non-mapped address) and an extra put_page.
Prevent this by nullifying the page pointer when dma_map fails.

Fixes: accd5883 ("net/mlx5e: Introduce RX Page-Reuse")
Signed-off-by: NInbar Karmy <inbark@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

napi->poll can be called with budget 0, e.g. in netpoll scenarios
where the caller only wants to poll TX rings
(poll_one_napi@net/core/netpoll.c).

The below commit changed RX polling from "while" loop to "do {} while",
which caused to ignore the initial budget and handle at least one RX
packet.

This fixes the following warning:
[ 2852.049194] mlx5e_napi_poll+0x0/0x260 [mlx5_core] exceeded budget in poll
[ 2852.049195] ------------[ cut here ]------------
[ 2852.049195] WARNING: CPU: 0 PID: 25691 at net/core/netpoll.c:171 netpoll_poll_dev+0x18a/0x1a0

Fixes: 4b7dfc99 ("net/mlx5e: Early-return on empty completion queues")
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Reported-by: NMartin KaFai Lau <kafai@fb.com>
Tested-by: NMartin KaFai Lau <kafai@fb.com>
Cc: kernel-team@fb.com
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

After the panic teardown firmware command, health_care detects the error
in PCI bus and calls the mlx5_pci_err_detected. This health_care flow is
no longer needed because the panic teardown firmware command will bring
down the PCI bus communication with the HCA.

The solution is to cancel the health care timer and its pending
workqueue request before sending panic teardown firmware command.

Kernel trace:
mlx5_core 0033:01:00.0: Shutdown was called
mlx5_core 0033:01:00.0: health_care:154:(pid 9304): handling bad device here
mlx5_core 0033:01:00.0: mlx5_handle_bad_state:114:(pid 9304): NIC state 1
mlx5_core 0033:01:00.0: mlx5_pci_err_detected was called
mlx5_core 0033:01:00.0: mlx5_enter_error_state:96:(pid 9304): start
mlx5_3:mlx5_ib_event:3061:(pid 9304): warning: event on port 0
mlx5_core 0033:01:00.0: mlx5_enter_error_state:104:(pid 9304): end
Unable to handle kernel paging request for data at address 0x0000003f
Faulting instruction address: 0xc0080000434b8c80

Fixes: 8812c24d ('net/mlx5: Add fast unload support in shutdown flow')
Signed-off-by: NHuy Nguyen <huyn@mellanox.com>
Reviewed-by: NMoshe Shemesh <moshe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

list_splice_init initializing waiting_events_list after splicing it to
temp list, therefore we should loop over temp list to fire the events.

Fixes: 4ca637a2 ("net/mlx5: Delay events till mlx5 interface's add complete for pci resume")
Signed-off-by: NHuy Nguyen <huyn@mellanox.com>
Signed-off-by: NFeras Daoud <ferasda@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>