Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 26 5月, 2015 5 次提交
  3. 22 5月, 2015 1 次提交
  5. 21 5月, 2015 2 次提交
    • M
      ipv6: fix ECMP route replacement · 27596472
      由 Michal Kubeček 提交于 
      When replacing an IPv6 multipath route with "ip route replace", i.e.
NLM_F_CREATE | NLM_F_REPLACE, fib6_add_rt2node() replaces only first
matching route without fixing its siblings, resulting in corrupted
siblings linked list; removing one of the siblings can then end in an
infinite loop.

IPv6 ECMP implementation is a bit different from IPv4 so that route
replacement cannot work in exactly the same way. This should be a
reasonable approximation:

1. If the new route is ECMP-able and there is a matching ECMP-able one
already, replace it and all its siblings (if any).

2. If the new route is ECMP-able and no matching ECMP-able route exists,
replace first matching non-ECMP-able (if any) or just add the new one.

3. If the new route is not ECMP-able, replace first matching
non-ECMP-able route (if any) or add the new route.

We also need to remove the NLM_F_REPLACE flag after replacing old
route(s) by first nexthop of an ECMP route so that each subsequent
nexthop does not replace previous one.

Fixes: 51ebd318 ("ipv6: add support of equal cost multipath (ECMP)")
Signed-off-by: NMichal Kubecek <mkubecek@suse.cz>
Acked-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      27596472
    • M
      ipv6: do not delete previously existing ECMP routes if add fails · 35f1b4e9
      由 Michal Kubeček 提交于 
      If adding a nexthop of an IPv6 multipath route fails, comment in
ip6_route_multipath() says we are going to delete all nexthops already
added. However, current implementation deletes even the routes it
hasn't even tried to add yet. For example, running

  ip route add 1234:5678::/64 \
      nexthop via fe80::aa dev dummy1 \
      nexthop via fe80::bb dev dummy1 \
      nexthop via fe80::cc dev dummy1

twice results in removing all routes first command added.

Limit the second (delete) run to nexthops that succeeded in the first
(add) run.

Fixes: 51ebd318 ("ipv6: add support of equal cost multipath (ECMP)")
Signed-off-by: NMichal Kubecek <mkubecek@suse.cz>
Acked-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      35f1b4e9
  7. 10 5月, 2015 1 次提交
    • M
      ipv6: Fixed source specific default route handling. · e16e888b
      由 Markus Stenberg 提交于 
      If there are only IPv6 source specific default routes present, the
host gets -ENETUNREACH on e.g. connect() because ip6_dst_lookup_tail
calls ip6_route_output first, and given source address any, it fails,
and ip6_route_get_saddr is never called.

The change is to use the ip6_route_get_saddr, even if the initial
ip6_route_output fails, and then doing ip6_route_output _again_ after
we have appropriate source address available.

Note that this is '99% fix' to the problem; a correct fix would be to
do route lookups only within addrconf.c when picking a source address,
and never call ip6_route_output before source address has been
populated.
Signed-off-by: NMarkus Stenberg <markus.stenberg@iki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      e16e888b
  9. 04 5月, 2015 1 次提交
  11. 02 5月, 2015 5 次提交
    • M
      ipv6: Remove DST_METRICS_FORCE_OVERWRITE and _rt6i_peer · afc4eef8
      由 Martin KaFai Lau 提交于 
      _rt6i_peer is no longer needed after the last patch,
'ipv6: Stop rt6_info from using inet_peer's metrics'.

DST_METRICS_FORCE_OVERWRITE is added by
commit e5fd387a ("ipv6: do not overwrite inetpeer metrics prematurely").
Since inetpeer is no longer used for metrics, this bit is also not needed.
Signed-off-by: NMartin KaFai Lau <kafai@fb.com>
Reviewed-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Michal Kubeček <mkubecek@suse.cz>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      afc4eef8
    • M
      ipv6: Stop rt6_info from using inet_peer's metrics · 4b32b5ad
      由 Martin KaFai Lau 提交于 
      inet_peer is indexed by the dst address alone.  However, the fib6 tree
could have multiple routing entries (rt6_info) for the same dst. For
example,
1. A /128 dst via multiple gateways.
2. A RTF_CACHE route cloned from a /128 route.

In the above cases, all of them will share the same metrics and
step on each other.

This patch will steer away from inet_peer's metrics and use
dst_cow_metrics_generic() for everything.

Change Highlights:
1. Remove rt6_cow_metrics() which currently acquires metrics from
   inet_peer for DST_HOST route (i.e. /128 route).
2. Add rt6i_pmtu to take care of the pmtu update to avoid creating a
   full size metrics just to override the RTAX_MTU.
3. After (2), the RTF_CACHE route can also share the metrics with its
   dst.from route, by:
   dst_init_metrics(&cache_rt->dst, dst_metrics_ptr(cache_rt->dst.from), true);
4. Stop creating RTF_CACHE route by cloning another RTF_CACHE route.  Instead,
   directly clone from rt->dst.

   [ Currently, cloning from another RTF_CACHE is only possible during
     rt6_do_redirect().  Also, the old clone is removed from the tree
     immediately after the new clone is added. ]

   In case of cloning from an older redirect RTF_CACHE, it should work as
   before.

   In case of cloning from an older pmtu RTF_CACHE, this patch will forget
   the pmtu and re-learn it (if there is any) from the redirected route.

The _rt6i_peer and DST_METRICS_FORCE_OVERWRITE will be removed
in the next cleanup patch.
Signed-off-by: NMartin KaFai Lau <kafai@fb.com>
Reviewed-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      4b32b5ad
    • M
      ipv6: Stop /128 route from disappearing after pmtu update · 653437d0
      由 Martin KaFai Lau 提交于 
      This patch is mostly from Steffen Klassert <steffen.klassert@secunet.com>.
I only removed the (rt6->rt6i_dst.plen == 128) check from
ip6_rt_update_pmtu() because the (rt6->rt6i_flags & RTF_CACHE) test
has already implied it.

This patch:
1. Create RTF_CACHE route for /128 non local route
2. After (1), all routes that allow pmtu update should have a RTF_CACHE
   clone.  Hence, stop updating MTU for any non RTF_CACHE route.
Signed-off-by: NMartin KaFai Lau <kafai@fb.com>
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>
Reviewed-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      653437d0
    • S
      ipv6: Extend the route lookups to low priority metrics. · 9fbdcfaf
      由 Steffen Klassert 提交于 
      We search only for routes with highest priority metric in
find_rr_leaf(). However if one of these routes is marked
as invalid, we may fail to find a route even if there is
a appropriate route with lower priority. Then we loose
connectivity until the garbage collector deletes the
invalid route. This typically happens if a host route
expires afer a pmtu event. Fix this by searching also
for routes with a lower priority metric.
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: NMartin KaFai Lau <kafai@fb.com>
Reviewed-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      9fbdcfaf
    • M
      ipv6: Consider RTF_CACHE when searching the fib6 tree · 1f56a01f
      由 Martin KaFai Lau 提交于 
      It is a prep work for the later bug-fix patch which will stop /128 route
from disappearing after pmtu update.

The later bug-fix patch will allow a /128 route and its RTF_CACHE clone
both exist at the same fib6_node.  To do this, we need to prepare the
existing fib6 tree search to expect RTF_CACHE for /128 route.

Note that the fn->leaf is sorted by rt6i_metric.  Hence,
RTF_CACHE (if there is any) is always at the front.  This property
leads to the following:

1. When doing ip6_route_del(), it should honor the RTF_CACHE flag which
   the caller is used to ask for deleting clone or non-clone.
   The rtm_to_fib6_config() should also check the RTM_F_CLONED and
   then set RTF_CACHE accordingly so that:
   - 'ip -6 r del...' will make ip6_route_del() to delete a route
     and all its clones. Note that its clones is flushed by fib6_del()
   - 'ip -6 r flush table cache' will make ip6_route_del() to
      only delete clone(s).

2. Exclude RTF_CACHE from addrconf_get_prefix_route() which
   should not configure on a cloned route.

3. No change is need for rt6_device_match() since it currently could
   return a RTF_CACHE clone route, so the later bug-fix patch will not
   affect it.
Signed-off-by: NMartin KaFai Lau <kafai@fb.com>
Reviewed-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      1f56a01f
  13. 01 4月, 2015 3 次提交
  15. 12 3月, 2015 1 次提交
  17. 10 3月, 2015 1 次提交
  19. 15 2月, 2015 1 次提交
    • M
      ipv6: fix ipv6_cow_metrics for non DST_HOST case · 3b471175
      由 Martin KaFai Lau 提交于 
      ipv6_cow_metrics() currently assumes only DST_HOST routes require
dynamic metrics allocation from inetpeer.  The assumption breaks
when ndisc discovered router with RTAX_MTU and RTAX_HOPLIMIT metric.
Refer to ndisc_router_discovery() in ndisc.c and note that dst_metric_set()
is called after the route is created.

This patch creates the metrics array (by calling dst_cow_metrics_generic) in
ipv6_cow_metrics().

Test:
radvd.conf:
interface qemubr0
{
	AdvLinkMTU 1300;
	AdvCurHopLimit 30;

	prefix fd00:face:face:face::/64
	{
		AdvOnLink on;
		AdvAutonomous on;
		AdvRouterAddr off;
	};
};

Before:
[root@qemu1 ~]# ip -6 r show | egrep -v unreachable
fd00:face:face:face::/64 dev eth0  proto kernel  metric 256  expires 27sec
fe80::/64 dev eth0  proto kernel  metric 256
default via fe80::74df:d0ff:fe23:8ef2 dev eth0  proto ra  metric 1024  expires 27sec

After:
[root@qemu1 ~]# ip -6 r show | egrep -v unreachable
fd00:face:face:face::/64 dev eth0  proto kernel  metric 256  expires 27sec mtu 1300
fe80::/64 dev eth0  proto kernel  metric 256  mtu 1300
default via fe80::74df:d0ff:fe23:8ef2 dev eth0  proto ra  metric 1024  expires 27sec mtu 1300 hoplimit 30

Fixes: 8e2ec639 (ipv6: don't use inetpeer to store metrics for routes.)
Signed-off-by: NMartin KaFai Lau <kafai@fb.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      3b471175
  21. 09 2月, 2015 1 次提交
    • M
      rt6_probe_deferred: Do not depend on struct ordering · 662f5533
      由 Michael Büsch 提交于 
      rt6_probe allocates a struct __rt6_probe_work and schedules a work handler rt6_probe_deferred.
But rt6_probe_deferred kfree's the struct work_struct instead of struct __rt6_probe_work.
This works, because struct work_struct is the first element of struct __rt6_probe_work.

Change it to kfree struct __rt6_probe_work to not implicitly depend on
struct work_struct being the first element.

This does not affect the generated code.
Signed-off-by: NMichael Buesch <m@bues.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      662f5533
  23. 26 1月, 2015 1 次提交
  25. 20 1月, 2015 1 次提交
  27. 18 1月, 2015 1 次提交
    • J
      netlink: make nlmsg_end() and genlmsg_end() void · 053c095a
      由 Johannes Berg 提交于 
      Contrary to common expectations for an "int" return, these functions
return only a positive value -- if used correctly they cannot even
return 0 because the message header will necessarily be in the skb.

This makes the very common pattern of

  if (genlmsg_end(...) < 0) { ... }

be a whole bunch of dead code. Many places also simply do

  return nlmsg_end(...);

and the caller is expected to deal with it.

This also commonly (at least for me) causes errors, because it is very
common to write

  if (my_function(...))
    /* error condition */

and if my_function() does "return nlmsg_end()" this is of course wrong.

Additionally, there's not a single place in the kernel that actually
needs the message length returned, and if anyone needs it later then
it'll be very easy to just use skb->len there.

Remove this, and make the functions void. This removes a bunch of dead
code as described above. The patch adds lines because I did

-	return nlmsg_end(...);
+	nlmsg_end(...);
+	return 0;

I could have preserved all the function's return values by returning
skb->len, but instead I've audited all the places calling the affected
functions and found that none cared. A few places actually compared
the return value with <= 0 in dump functionality, but that could just
be changed to < 0 with no change in behaviour, so I opted for the more
efficient version.

One instance of the error I've made numerous times now is also present
in net/phonet/pn_netlink.c in the route_dumpit() function - it didn't
check for <0 or <=0 and thus broke out of the loop every single time.
I've preserved this since it will (I think) have caused the messages to
userspace to be formatted differently with just a single message for
every SKB returned to userspace. It's possible that this isn't needed
for the tools that actually use this, but I don't even know what they
are so couldn't test that changing this behaviour would be acceptable.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      053c095a
  29. 06 1月, 2015 2 次提交
  31. 24 10月, 2014 3 次提交
    • M
      ipv6: Avoid redoing fib6_lookup() with reachable = 0 by saving fn · 367efcb9
      由 Martin KaFai Lau 提交于 
      This patch save the fn before doing rt6_backtrack.
Hence, without redo-ing the fib6_lookup(), saved_fn can be used
to redo rt6_select() with RT6_LOOKUP_F_REACHABLE off.

Some minor changes I think make sense to review as a single patch:
* Remove the 'out:' goto label.
* Remove the 'reachable' variable. Only use the 'strict' variable instead.

After this patch, "failing ip6_ins_rt()" should be the only case that
requires a redo of fib6_lookup().

Cc: David Miller <davem@davemloft.net>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NMartin KaFai Lau <kafai@fb.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      367efcb9
    • M
      ipv6: Avoid redoing fib6_lookup() for RTF_CACHE hit case · 94c77bb4
      由 Martin KaFai Lau 提交于 
      When there is a RTF_CACHE hit, no need to redo fib6_lookup()
with reachable=0.

Cc: David Miller <davem@davemloft.net>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NMartin KaFai Lau <kafai@fb.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      94c77bb4
    • M
      ipv6: Remove BACKTRACK macro · a3c00e46
      由 Martin KaFai Lau 提交于 
      It is the prep work to reduce the number of calls to fib6_lookup().

The BACKTRACK macro could be hard-to-read and error-prone due to
its side effects (mainly goto).

This patch is to:
1. Replace BACKTRACK macro with a function (fib6_backtrack) with the following
   return values:
   * If it is backtrack-able, returns next fn for retry.
   * If it reaches the root, returns NULL.
2. The caller needs to decide if a backtrack is needed (by testing
   rt == net->ipv6.ip6_null_entry).
3. Rename the goto labels in ip6_pol_route() to make the next few
   patches easier to read.

Cc: David Miller <davem@davemloft.net>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NMartin KaFai Lau <kafai@fb.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      a3c00e46
  33. 01 10月, 2014 1 次提交
    • H
      ipv6: remove rt6i_genid · 705f1c86
      由 Hannes Frederic Sowa 提交于 
      Eric Dumazet noticed that all no-nonexthop or no-gateway routes which
are already marked DST_HOST (e.g. input routes routes) will always be
invalidated during sk_dst_check. Thus per-socket dst caching absolutely
had no effect and early demuxing had no effect.

Thus this patch removes rt6i_genid: fn_sernum already gets modified during
add operations, so we only must ensure we mutate fn_sernum during ipv6
address remove operations. This is a fairly cost extensive operations,
but address removal should not happen that often. Also our mtu update
functions do the same and we heard no complains so far. xfrm policy
changes also cause a call into fib6_flush_trees. Also plug a hole in
rt6_info (no cacheline changes).

I verified via tracing that this change has effect.

Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: YOSHIFUJI Hideaki <hideaki@yoshifuji.org>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Cc: Martin Lau <kafai@fb.com>
Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      705f1c86
  35. 25 8月, 2014 2 次提交
  37. 22 5月, 2014 1 次提交
  39. 17 5月, 2014 1 次提交
  41. 16 5月, 2014 1 次提交
    • D
      ipv6: update Destination Cache entries when gateway turn into host · be7a010d
      由 Duan Jiong 提交于 
      RFC 4861 states in 7.2.5:

	The IsRouter flag in the cache entry MUST be set based on the
         Router flag in the received advertisement.  In those cases
         where the IsRouter flag changes from TRUE to FALSE as a result
         of this update, the node MUST remove that router from the
         Default Router List and update the Destination Cache entries
         for all destinations using that neighbor as a router as
         specified in Section 7.3.3.  This is needed to detect when a
         node that is used as a router stops forwarding packets due to
         being configured as a host.

Currently, when dealing with NA Message which IsRouter flag changes from
TRUE to FALSE, the kernel only removes router from the Default Router List,
and don't update the Destination Cache entries.

Now in order to update those Destination Cache entries, i introduce
function rt6_clean_tohost().
Signed-off-by: NDuan Jiong <duanj.fnst@cn.fujitsu.com>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      be7a010d
  43. 14 5月, 2014 1 次提交
    • L
      net: Use fwmark reflection in PMTU discovery. · 1b3c61dc
      由 Lorenzo Colitti 提交于 
      Currently, routing lookups used for Path PMTU Discovery in
absence of a socket or on unmarked sockets use a mark of 0.
This causes PMTUD not to work when using routing based on
netfilter fwmark mangling and fwmark ip rules, such as:

  iptables -j MARK --set-mark 17
  ip rule add fwmark 17 lookup 100

This patch causes these route lookups to use the fwmark from the
received ICMP error when the fwmark_reflect sysctl is enabled.
This allows the administrator to make PMTUD work by configuring
appropriate fwmark rules to mark the inbound ICMP packets.

Black-box tested using user-mode linux by pointing different
fwmarks at routing tables egressing on different interfaces, and
using iptables mangling to mark packets inbound on each interface
with the interface's fwmark. ICMPv4 and ICMPv6 PMTU discovery
work as expected when mark reflection is enabled and fail when
it is disabled.
Signed-off-by: NLorenzo Colitti <lorenzo@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      1b3c61dc
  45. 29 4月, 2014 1 次提交
  47. 16 4月, 2014 1 次提交
  49. 15 4月, 2014 1 次提交