Dell Latitude 5x30 and 6x30 series of machines all have
a single 4-pin headset jack. Enabling line in mode for such jack
is very confusing (you would only get mono input, and would have to
use non-standard adapters), so remove the option by default.
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

From what I can conclude all GPIO handling was removed in 2009.
Remove dead code remnants.
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

These are compatible with standard ALC269 parser.
Signed-off-by: NKailang Yang <kailang@realtek.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

In case there is one "Headphone Jack" and one "Dock Headphone Jack",
one of them will get an index, even though that is not needed.
This patch fixes that issue.

BugLink: https://bugs.launchpad.net/bugs/1060729Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

After the recent patch "ALSA: hda - use both input paths on Conexant
auto parser" suddenly we can have more than one "Mic Boost", this
happened on Acer Aspire One 722. Therefore we must add the possibility
to put an index on this "Mic Boost" just as we do for the other
"Mic Boost" earlier in the same function.

BugLink: https://bugs.launchpad.net/bugs/1059523Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

There was a race condition when the system suspends while hda_power_work
is running in the work queue.  If system suspend (snd_hda_suspend)
happens after the work queue releases power_lock but before it calls
hda_call_codec_suspend,  codec_suspend runs with power_on=0, causing the
codec to power up for register reads, and hanging when it calls
cancel_delayed_work_sync from the running work queue.

The call chain from the work queue will look like this:
hda_power_work <<- power_on = 1, unlock, then power_on cleard by suspend
  hda_call_codec_suspend
    hda_set_power_state
      snd_hda_codec_read
        codec_exec_verb
          snd_hda_power_up
	    snd_hda_power_save
	      __snd_hda_power_up
	        cancel_delayed_work_sync <<-- cancelling executing wq

Fix this by waiting for the work queue to finish before starting suspend
if suspend is not happening on the work queue.
Signed-off-by: NDylan Reid <dgreid@chromium.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

In commit af741c15 ("ALSA: hda/realtek - Call alc_auto_parse_customize_define()
always after fixup"), alc_auto_parse_customize_define was moved after
detection of ALC271X.

The problem is that detection of ALC271X relies on spec->cdefine.platform_type,
and it's set on alc_auto_parse_customize_define.

Move the alc_auto_parse_customize_define and its required fixup setup
before the block doing the ALC271X and other codec setup.

BugLink: https://bugs.launchpad.net/bugs/1006690Signed-off-by: NHerton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Reviewed-by: NDavid Henningsson <david.henningsson@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The Lenovo IdeaPad U310 has an internal mic where the right channel
is phase inverted.
Signed-off-by: NFelix Kaechele <felix@fetzig.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

For less duplication of code between codecs, and to make it easier
in the future to improve code for all codecs simultaneously.
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Moving towards less duplication of code between codecs - this patch
takes some of the common code of unsol event handling and makes it
generic.
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Tested with LPIB delay without any issues.
Signed-off-by: NPierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

DMA Position in Buffer (DPIB) should be used for
ring buffer management, while LPIB register provides
information on the number of samples transfered on
the link. The difference between the two pieces of
information corresponds to hardware/DMA buffering.

This patch reports this difference in runtime->delay, and
removes the use of the COMBO mode on recent Intel hardware.

Credits to Takashi Iwai for an initial patch.

[rebased to for-next branch and replaced snd_printk() with
 snd_printdd() by tiwai]
Signed-off-by: NPierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

SSYNC bits are typically used to start multiple
streams synchronously. It makes sense to use them
for a single stream for a more predictable startup
sequence. The transfers only start once the DMA and
FIFOs are ready. This results in a better correlation
between timestamps and number of samples played.

Credits to Kar Leong Wang for suggesting this
improvement.
Signed-off-by: NPierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

If headphone jack can't detect plug presence, and we have the jack in
the jack table, snd_hda_jack_detect will return the plug as always
present (as it'll be considered as a phantom jack). The problem is that
when this happens, line out pins will always be disabled, resulting in
no sound if there are no headphones connected.

This was reported as a no sound problem after suspend on
http://bugs.launchpad.net/bugs/1052499, since the bug doesn't manifests
on first initialization before the phantom jack is added, but on resume
we reexecute the initialization code, and via_hp_automute starts
reporting HP always present with the jack now on the table.

BugLink: https://bugs.launchpad.net/bugs/1052499Signed-off-by: NHerton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Cc: <stable@vger.kernel.org> [v3.6+]
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NOleksij Rempel <bug-track@fisher-privat.net>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

On the Thinkpad W520 - and probably several other machines with
Conexant 506x chips - the Dock Mic and Mic are connected to the
same two selector nodes. This patch will make Dock Mic take one
selector node and Mic take the other, when possible.

Without the patch, both paths would take the first selector,
leading to the normal Mic's volume being controlled by
"Dock Mic Boost".
(On other machines, this could instead fixup similar problems between
Mic and Line In, for example.)

BugLink: https://bugs.launchpad.net/bugs/1037642Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The standard name (and what PulseAudio picks up) is "Dock Mic",
not "Docking Mic" or "Docking-Station".
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When the input gain for the internal mic is set to its maximum level,
the background noise becomes so high - and any relevant signal clipped -
that the setting becomes unusable. It is better to limit the amplification.

BugLink: https://bugs.launchpad.net/bugs/1052460Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Cc: <stable@vger.kernel.org> [v3.5+]
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

A new PCI id 0x0d0c for Haswell HDA Controller.

[root@SKBM04SDP ~]# lspci |grep Audio
00:03.0 Audio device: Intel Corporation Device 0d0c (rev 02)
00:1b.0 Audio device: Intel Corporation Lynx Point HD Audio Controller
Signed-off-by: NWang Xingchao <xingchao.wang@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Some of new HP laptops have a LED for microphone (or recording) mute,
and it's controlled by GPIO pin 3.

Bind this with the capture switch to turn it on/off properly by the
mixer change.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

ASUS X53S also suffers from the same issue as in commit c302d613.
Use POS_FIX_POSBUF for this hardware, too.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=47461Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Set the default value of position_fix -1, and allow user passing
position_fix=0 explicitly to set the "auto" position-fix mode.
Otherwise the auto mode may be switched to others like COMBO of
VIACOMBO when the controller prefers it, thus user can't set the auto
mode any longer.

Also updated the documentation appropriately, too.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Due to the definitions of CS420X_IMAC27_122 and CS420X_APPLE as
aliases, the rest enums are set to duplicated values unexpectedly.
Move the alias definitions at the end so that the enum values are
defined in the proper order.
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

MacBook Pro 10,1 needs a few adjustments to make it working:
- more COEF verbs
- some pin config overrides to disable the unused pin (0x0d, 0x12),
  and fix the internal mic (0x0e)

In addition, it uses GPIO 1 and 3 like other MacBooks.

The internal digital mic on the machine is still problematic: it seems
that only the right channel is used and the left is always static.
This looks like a hardware design, so we need to cope in the software
side somehow...

The primary information and test were brought from Daniel J Blueman.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

... to make easier to integrate into the common generic parser in near
future.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

snd_hda_pick_fixup() didn't check the case where the device mask bits
are set, typically used for SND_PCI_QUIRK_VENDOR() entries.  Fix this.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Originally the bogus period at BDL head was introduced as a workaround
for the mismatching position update at the period boundary, typically
seen on dmix.  However, for applications like PulseAudio that don't
require period wake ups, this workaround is just superfluous.  Thus
better to disable it when no_period_wakeup is given in hw_params.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Commit c20c5a84 changed some chipsets to
default to POS_FIX_COMBO so they now use POS_FIX_LPIB instead of
POS_FIX_POSBUF. Since then I've been getting artifacts on playback, including
repeated sounds on my Asus laptop.

My hardware is Cougar Point which the commit log of
c20c5a84 mentions as tested so POS_FIX_COMBO
probably works in general but apparently it doesn't on Asus K53E therefore the
need for the quirk.
Signed-off-by: NCatalin Iacob <iacobcatalin@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NTakashi Iwai <tiwai@suse.de>

snd_hda_codec_reset() calls restore_pincfgs() where the codec is
powered up again, which eventually tries to resume and initialize via
the callbacks of the codec.  However, it's the place just after codec
free callback, thus no codec callbacks should be called after that.
On a codec like CS4206, it results in Oops due to the access in init
callback.

This patch fixes the issue by clearing the codec callbacks properly
after freeing codec.
Reported-by: NDaniel J Blueman <daniel@quora.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The purpose of this flag is unclear. If the problem is that some machines
have broken misc/NO_PRESENCE bits, they should be fixed by pin fixups.

In addition, this causes jack detection functionality to be flawed on
the M31EI, where there are two jacks without jack detection (which is
properly marked as NO_PRESENCE), but due to ignore_misc_bit, these
jacks are instead being reported as being present but always unplugged.

BugLink: https://bugs.launchpad.net/bugs/939161Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Some old Nvidia HDMI codecs with 8ch support only 2/8 or
2/6/8 channels and with the fixed CLFE-first map.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

... instead of the standard fixed channel maps.
The generic HDMI is based on the audio infoframe, and its configuration
can be selected via CA bits.  Thus we need a translation between the
CA index and the verbose channel map list.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Although HD-audio allows pair-wise channel configurations, only the
fixed channel positions are used in this version.  In future, this can
be changed and allow user to modify the channel positions.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Recently the check for non-PCM stream state was added to the generic
HDMI driver code.  But this check should be done rather to each pin
instead of each converter.  Otherwise when a different converter is
assigned at the next open, the audio infoframe can be inconsistent
with the setup using the previous converter.

For fixing this issue, this patch moves the state of the current
non-PCM status from per_cvt to per_pin.  (In addition an unused
argument cvt_nid is stripped from hdmi_setup_channel_mapping())
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

For multiple speaker outs, the names were previously
"Speaker,0", "Speaker,1", "Center"/"LFE", "Speaker,3". This is
inconsistent, confusing, and is not picked up correctly by PulseAudio.
Instead use "Front", "Surround", "Center"/"LFE", "Side" which
is more standard.

BugLink: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1046734Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

With the commit [2faa3bf1: ALSA: hda - Rewrite the mute-LED hook with
vmaster hook in patch_sigmatel.c], the former Master volume control
was converted to PCM.  This was supposed to be covered by the vmaster
control.  But due to the lack of "PCM" slave definition, this didn't
happen properly.  The patch fixes the missing entry.
Reported-by: NAndrew Shadura <bugzilla@tut.by>
Cc: <stable@vger.kernel.org> [v3.4+]
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

For HBR stream test, use straight channel mapping way.
when switched back to "speaker-test -c8", even the audio
infoframe is up-to-date, there should be correct channel mapping setup.
Signed-off-by: NWang Xingchao <xingchao.wang@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>