Reorder struct netns_ct so that atomic_t "count" changes don't
slowdown users of read mostly fields.

This is based on Eric Dumazet's proposed patch:
 "netfilter: conntrack: remove the central spinlock"
 http://thread.gmane.org/gmane.linux.network/268758/focus=47306

The tricky part of cache-aligning this structure, that it is getting
inlined in struct net (include/net/net_namespace.h), thus changes to
other netns_xxx structures affects our alignment.

Eric's original patch contained an ambiguity on 32-bit regarding
alignment in struct net.  This patch also takes 32-bit into account,
and in case of changed (struct net) alignment sysctl_xxx entries have
been ordered according to how often they are accessed.
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

RFC 4191 states in 3.5:

   When a host avoids using any non-reachable router X and instead sends
   a data packet to another router Y, and the host would have used
   router X if router X were reachable, then the host SHOULD probe each
   such router X's reachability by sending a single Neighbor
   Solicitation to that router's address.  A host MUST NOT probe a
   router's reachability in the absence of useful traffic that the host
   would have sent to the router if it were reachable.  In any case,
   these probes MUST be rate-limited to no more than one per minute per
   router.

Currently, when the neighbour corresponding to a router falls into
NUD_FAILED, it's never considered again. Introduce a new rt6_nud_state
value, RT6_NUD_FAIL_PROBE, which suggests the route should not be used but
should be probed with a single NS. The probe is ratelimited by the existing
code. To better distinguish meanings of the failure values, rename
RT6_NUD_FAIL_SOFT to RT6_NUD_FAIL_DO_RR.
Signed-off-by: NJiri Benc <jbenc@redhat.com>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't needlessly recompute 'opt[opt_iter + 1]' as we already have it
stored in 'tag_len'.
Signed-off-by: NPaul Moore <pmoore@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

And use it if possible.
Signed-off-by: NFlorent Fourcot <florent.fourcot@enst-bretagne.fr>
Reviewed-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFlorent Fourcot <florent.fourcot@enst-bretagne.fr>
Reviewed-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make the behaviour similar to ipv4. This will allow user to set sysctl
default neigh param values and these values will be respected even by
devices registered before (that ones what do not have address set yet).
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously inet devices were only constructed when addresses are added.
Therefore the default neigh parms values they get are the ones at the
time of these operations.

Now that we're creating inet devices earlier, this changes the behaviour
of default neigh parms values in an incompatible way (see bug #8519).

This patch creates a compromise by setting the default values at the
same point as before but only for those that have not been explicitly
set by the user since the inet device's creation.

Introduced by:
commit 8030f544
Author: Herbert Xu <herbert@gondor.apana.org.au>
Date:   Thu Feb 22 01:53:47 2007 +0900

    [IPV4] devinet: Register inetdev earlier.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This will be needed later on to provide better management of default values.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch converts the neigh param members to an array. This allows easier
manipulation which will be needed later on to provide better management of
default values.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 6da7c8fc ("qdisc: allow setting default queuing discipline")
added the ability to change default qdisc from pfifo_fast to say fq

But as most modern ethernet devices are multiqueue, we cant really
see all the statistics from "tc -s qdisc show", as the default root
qdisc is mq.

This patch adds the calls to qdisc_list_add() to mq and mqprio
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no more space in u8 ifa_flags. So do what davem suffested and
add another netlink attr called IFA_FLAGS for carry more flags.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NThomas Haller <thaller@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the introduction of TCP Small Queues, TSO auto sizing, and TCP
pacing, we can implement Automatic Corking in the kernel, to help
applications doing small write()/sendmsg() to TCP sockets.

Idea is to change tcp_push() to check if the current skb payload is
under skb optimal size (a multiple of MSS bytes)

If under 'size_goal', and at least one packet is still in Qdisc or
NIC TX queues, set the TCP Small Queue Throttled bit, so that the push
will be delayed up to TX completion time.

This delay might allow the application to coalesce more bytes
in the skb in following write()/sendmsg()/sendfile() system calls.

The exact duration of the delay is depending on the dynamics
of the system, and might be zero if no packet for this flow
is actually held in Qdisc or NIC TX ring.

Using FQ/pacing is a way to increase the probability of
autocorking being triggered.

Add a new sysctl (/proc/sys/net/ipv4/tcp_autocorking) to control
this feature and default it to 1 (enabled)

Add a new SNMP counter : nstat -a | grep TcpExtTCPAutoCorking
This counter is incremented every time we detected skb was under used
and its flush was deferred.

Tested:

Interesting effects when using line buffered commands under ssh.

Excellent performance results in term of cpu usage and total throughput.

lpq83:~# echo 1 >/proc/sys/net/ipv4/tcp_autocorking
lpq83:~# perf stat ./super_netperf 4 -t TCP_STREAM -H lpq84 -- -m 128
9410.39

 Performance counter stats for './super_netperf 4 -t TCP_STREAM -H lpq84 -- -m 128':

      35209.439626 task-clock                #    2.901 CPUs utilized
             2,294 context-switches          #    0.065 K/sec
               101 CPU-migrations            #    0.003 K/sec
             4,079 page-faults               #    0.116 K/sec
    97,923,241,298 cycles                    #    2.781 GHz                     [83.31%]
    51,832,908,236 stalled-cycles-frontend   #   52.93% frontend cycles idle    [83.30%]
    25,697,986,603 stalled-cycles-backend    #   26.24% backend  cycles idle    [66.70%]
   102,225,978,536 instructions              #    1.04  insns per cycle
                                             #    0.51  stalled cycles per insn [83.38%]
    18,657,696,819 branches                  #  529.906 M/sec                   [83.29%]
        91,679,646 branch-misses             #    0.49% of all branches         [83.40%]

      12.136204899 seconds time elapsed

lpq83:~# echo 0 >/proc/sys/net/ipv4/tcp_autocorking
lpq83:~# perf stat ./super_netperf 4 -t TCP_STREAM -H lpq84 -- -m 128
6624.89

 Performance counter stats for './super_netperf 4 -t TCP_STREAM -H lpq84 -- -m 128':
      40045.864494 task-clock                #    3.301 CPUs utilized
               171 context-switches          #    0.004 K/sec
                53 CPU-migrations            #    0.001 K/sec
             4,080 page-faults               #    0.102 K/sec
   111,340,458,645 cycles                    #    2.780 GHz                     [83.34%]
    61,778,039,277 stalled-cycles-frontend   #   55.49% frontend cycles idle    [83.31%]
    29,295,522,759 stalled-cycles-backend    #   26.31% backend  cycles idle    [66.67%]
   108,654,349,355 instructions              #    0.98  insns per cycle
                                             #    0.57  stalled cycles per insn [83.34%]
    19,552,170,748 branches                  #  488.244 M/sec                   [83.34%]
       157,875,417 branch-misses             #    0.81% of all branches         [83.34%]

      12.130267788 seconds time elapsed
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Several files refer to an old address for the Free Software Foundation
in the file header comment.  Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Several files refer to an old address for the Free Software Foundation
in the file header comment.  Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.

CC: Vlad Yasevich <vyasevich@gmail.com>
CC: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

kill memcg_tcp_enter_memory_pressure.  The only function of
memcg_tcp_enter_memory_pressure was to reduce deal with the
unnecessary abstraction that was tcp_memcontrol.  Now that struct
tcp_memcontrol is gone remove this unnecessary function, the
unnecessary function pointer, and modify sk_enter_memory_pressure to
set this field directly, just as sk_leave_memory_pressure cleas this
field directly.

This fixes a small bug I intruduced when killing struct tcp_memcontrol
that caused memcg_tcp_enter_memory_pressure to never be called and
thus failed to ever set cg_proto->memory_pressure.

Remove the cg_proto enter_memory_pressure function as it now serves
no useful purpose.

Don't test cg_proto->memory_presser in sk_leave_memory_pressure before
clearing it.  The test was originally there to ensure that the pointer
was non-NULL.  Now that cg_proto is not a pointer the pointer does not
matter.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code to detect fragments in checksum_setup() was missing for IPv4 and
too eager for IPv6. (It transpires that Windows seems to send IPv6 packets
with a fragment header even if they are not a fragment - i.e. offset is zero,
and M bit is not set).

This patch also incorporates a fix to callers of maybe_pull_tail() where
skb->network_header was being erroneously added to the length argument.
Signed-off-by: NPaul Durrant <paul.durrant@citrix.com>
Signed-off-by: NZoltan Kiss <zoltan.kiss@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
cc: David Miller <davem@davemloft.net>
Acked-by: NWei Liu <wei.liu2@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The channel switch notification should be sent under the
wdev/sdata-lock, preferably in the same moment as the channel change
happens, to avoid races by other callers (e.g. start/stop_ap).
This also adds the previously missing sdata_lock protection in
csa_finalize_work.
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NSimon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Change cfg80211 and mac80211 to use cfg80211_mgmt_tx_params
struct to aggregate parameters for mgmt_tx functions.
This makes the functions' signatures less clumsy and allows
less painful parameters extension.
Signed-off-by: NAndrei Otcheretianski <andrei.otcheretianski@intel.com>
[fix all other drivers]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Currently retransmitted DATA chunks could also be used for
RTT measurements since there are no flag to identify whether
the transmitted DATA chunk is a new one or a retransmitted one.
This problem is introduced by commit ae19c548 ("sctp: remove
'resent' bit from the chunk") which inappropriately removed the
'resent' bit completely, instead of doing this, we should set
the resent bit only for the retransmitted DATA chunks.
Signed-off-by: NXufeng Zhang <xufeng.zhang@windriver.com>
Acked-by: NVlad Yasevich <vyasevich@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

u8 was used in some other places, just stick to the enum,
this forces us to express the values that are expected.
Signed-off-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add a new field to ieee80211_chanctx_conf to indicate
the min required channel configuration.

Tuning to a narrower channel might help reducing
the noise level and saving some power.

The min required channel definition is the max of
all min required channel definitions of the interfaces
bound to this channel context.

In AP mode, use 20MHz when there are no connected station.
When a new station is added/removed, calculate the new max
bandwidth supported by any of the stations (e.g. 80MHz when
80MHz and 40MHz stations are connected).

In other cases, simply use bss_conf.chandef as the
min required chandef.

Notify drivers about changes to this field by calling
drv_change_chanctx with a new CHANGE_MIN_WIDTH notification.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Certain vendors may want to disable the processing of
country IEs so that they can continue using the regulatory
domain the driver or user has set.  Currently there is no
way to stop the core from processing country IEs, so add
support to the core to ignore country IE hints.

Cc: Mihir Shete <smihir@qti.qualcomm.com>
Cc: Henri Bahini <hbahini@qca.qualcomm.com>
Cc: Tushnim Bhattacharyya <tushnimb@qca.qualcomm.com>
Signed-off-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

802.11 cards may have different country IE parsing behavioural
preferences and vendors may want to support these. These preferences
were managed by the REGULATORY_CUSTOM_REG and the REGULATORY_STRICT_REG
flags and their combination. Instead of using this existing notation,
split out the country IE behavioural preferences as a new flag. This
will allow us to add more customizations easily and make the code more
maintainable.

Cc: Mihir Shete <smihir@qti.qualcomm.com>
Cc: Henri Bahini <hbahini@qca.qualcomm.com>
Cc: Tushnim Bhattacharyya <tushnimb@qca.qualcomm.com>
Signed-off-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
[fix up conflicts]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

We'll expand this later, this will make it easier to
classify and review what things are related to regulatory
or not.

Coccinelle only missed 4 hits, which I had to do manually,
supplying the SmPL in case of merge conflicts.

@@
struct wiphy *wiphy;
@@
-wiphy->flags |= WIPHY_FLAG_CUSTOM_REGULATORY
+wiphy->regulatory_flags |= REGULATORY_CUSTOM_REG
@@
expression e;
@@
-e->flags |= WIPHY_FLAG_CUSTOM_REGULATORY
+e->regulatory_flags |= REGULATORY_CUSTOM_REG
@@
struct wiphy *wiphy;
@@
-wiphy->flags &= ~WIPHY_FLAG_CUSTOM_REGULATORY
+wiphy->regulatory_flags &= ~REGULATORY_CUSTOM_REG
@@
struct wiphy *wiphy;
@@
-wiphy->flags & WIPHY_FLAG_CUSTOM_REGULATORY
+wiphy->regulatory_flags & REGULATORY_CUSTOM_REG

@@
struct wiphy *wiphy;
@@
-wiphy->flags |= WIPHY_FLAG_STRICT_REGULATORY
+wiphy->regulatory_flags |= REGULATORY_STRICT_REG
@@
expression e;
@@
-e->flags |= WIPHY_FLAG_STRICT_REGULATORY
+e->regulatory_flags |= REGULATORY_STRICT_REG
@@
struct wiphy *wiphy;
@@
-wiphy->flags &= ~WIPHY_FLAG_STRICT_REGULATORY
+wiphy->regulatory_flags &= ~REGULATORY_STRICT_REG
@@
struct wiphy *wiphy;
@@
-wiphy->flags & WIPHY_FLAG_STRICT_REGULATORY
+wiphy->regulatory_flags & REGULATORY_STRICT_REG

@@
struct wiphy *wiphy;
@@
-wiphy->flags |= WIPHY_FLAG_DISABLE_BEACON_HINTS
+wiphy->regulatory_flags |= REGULATORY_DISABLE_BEACON_HINTS
@@
expression e;
@@
-e->flags |= WIPHY_FLAG_DISABLE_BEACON_HINTS
+e->regulatory_flags |= REGULATORY_DISABLE_BEACON_HINTS
@@
struct wiphy *wiphy;
@@
-wiphy->flags &= ~WIPHY_FLAG_DISABLE_BEACON_HINTS
+wiphy->regulatory_flags &= ~REGULATORY_DISABLE_BEACON_HINTS
@@
struct wiphy *wiphy;
@@
-wiphy->flags & WIPHY_FLAG_DISABLE_BEACON_HINTS
+wiphy->regulatory_flags & REGULATORY_DISABLE_BEACON_HINTS

Generated-by: Coccinelle SmPL
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Cc: Mihir Shete <smihir@qti.qualcomm.com>
Cc: Henri Bahini <hbahini@qca.qualcomm.com>
Cc: Tushnim Bhattacharyya <tushnimb@qca.qualcomm.com>
Signed-off-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
[fix up whitespace damage, overly long lines]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This adds generic cipher scheme support to mac80211, such schemes
are fully under control by the driver. On hw registration drivers
may specify additional HW ciphers with a scheme how these ciphers
have to be handled by mac80211 TX/RR. A cipher scheme specifies a
cipher suite value, a size of the security header to be added to
or stripped from frames and how the PN is to be verified on RX.
Signed-off-by: NMax Stepanov <Max.Stepanov@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

To report channel width correctly we have
to send correct channel parameters from
mac80211 when calling cfg80211_cac_event().

This is required in case of using channel width
higher than 20MHz and we have to set correct
dfs channel state after CAC (NL80211_DFS_AVAILABLE).
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Reviewed-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

wiphy_apply_custom_regulatory() implies WIPHY_FLAG_CUSTOM_REGULATORY
but we never enforced it, do that now and warn if the driver
didn't set it. All drivers should be following this today already.

Having WIPHY_FLAG_CUSTOM_REGULATORY does not however mean you will
use wiphy_apply_custom_regulatory() though, you may have your own
_orig value set up tools / helpers. The intel drivers are examples
of this type of driver.
Signed-off-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

These two flags are used for the same purpose, just
combine them into a no-ir flag to annotate no initiating
radiation is allowed.

Old userspace sending either flag will have it treated as
the no-ir flag. To be considerate to older userspace we
also send both the no-ir flag and the old no-ibss flags.
Newer userspace will have to be aware of older kernels.

Update all places in the tree using these flags with the
following semantic patch:

@@
@@
-NL80211_RRF_PASSIVE_SCAN
+NL80211_RRF_NO_IR
@@
@@
-NL80211_RRF_NO_IBSS
+NL80211_RRF_NO_IR
@@
@@
-IEEE80211_CHAN_PASSIVE_SCAN
+IEEE80211_CHAN_NO_IR
@@
@@
-IEEE80211_CHAN_NO_IBSS
+IEEE80211_CHAN_NO_IR
@@
@@
-NL80211_RRF_NO_IR | NL80211_RRF_NO_IR
+NL80211_RRF_NO_IR
@@
@@
-IEEE80211_CHAN_NO_IR | IEEE80211_CHAN_NO_IR
+IEEE80211_CHAN_NO_IR
@@
@@
-(NL80211_RRF_NO_IR)
+NL80211_RRF_NO_IR
@@
@@
-(IEEE80211_CHAN_NO_IR)
+IEEE80211_CHAN_NO_IR

Along with some hand-optimisations in documentation, to
remove duplicates and to fix some indentation.
Signed-off-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
[do all the driver updates in one go]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Commit bceaa902 ("inet: prevent leakage
of uninitialized memory to user in recv syscalls") conditionally updated
addr_len if the msg_name is written to. The recv_error and rxpmtu
functions relied on the recvmsg functions to set up addr_len before.

As this does not happen any more we have to pass addr_len to those
functions as well and set it to the size of the corresponding sockaddr
length.

This broke traceroute and such.

Fixes: bceaa902 ("inet: prevent leakage of uninitialized memory to user in recv syscalls")
Reported-by: NBrad Spengler <spender@grsecurity.net>
Reported-by: Tom Labanowski
Cc: mpb <mpb.mail@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix another really stupid bug - I introduced genl_set_err()
precisely to be able to adjust the group and reject invalid
ones, but then forgot to do so.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Unfortunately, I introduced a tremendously stupid bug into
genlmsg_multicast() when doing all those multicast group
changes: it adjusts the group number, but then passes it
to genlmsg_multicast_netns() which does that again.

Somehow, my tests failed to catch this, so add a warning
into genlmsg_multicast_netns() and remove the offending
group ID adjustment.

Also add a warning to the similar code in other functions
so people who misuse them are more loudly warned.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Register generic netlink multicast groups as an array with
the family and give them contiguous group IDs. Then instead
of passing the global group ID to the various functions that
send messages, pass the ID relative to the family - for most
families that's just 0 because the only have one group.

This avoids the list_head and ID in each group, adding a new
field for the mcast group ID offset to the family.

At the same time, this allows us to prevent abusing groups
again like the quota and dropmon code did, since we can now
check that a family only uses a group it owns.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This doesn't really change anything, but prepares for the
next patch that will change the APIs to pass the group ID
within the family, rather than the global group ID.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a static inline to generic netlink to wrap netlink_set_err()
to make it easier to use here - use it in openvswitch (the only
generic netlink user of netlink_set_err()).
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There's no reason to have the family pointer there since it
can just be passed internally where needed, so remove it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are no users of this API remaining, and we'll soon
change group registration to be static (like ops are now)
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As suggested by David Miller, make genl_register_family_with_ops()
a macro and pass only the array, evaluating ARRAY_SIZE() in the
macro, this is a little safer.

The openvswitch has some indirection, assing ops/n_ops directly in
that code. This might ultimately just assign the pointers in the
family initializations, saving the struct genl_family_and_ops and
code (once mcast groups are handled differently.)
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that the ops assignment is just two variables rather than a
long list iteration etc., there's no reason to separately export
__genl_register_family() and __genl_register_family_with_ops().

Unify the two functions into __genl_register_family() and make
genl_register_family_with_ops() call it after assigning the ops.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>