The initial function and setup tables can be marked as constant.
Reported-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>

drivers/net/built-in.o: In function `bfa_ioc_ct2_poweron':
(.text+0xcdc90): multiple definition of `bfa_ioc_ct2_poweron'
drivers/scsi/built-in.o:(.text+0x17f9a0): first defined here

This patch renames bfa_ioc_ct2_poweron() to bfa_nw_ioc_ct2_poweron() to avoid
multiple definition with Brocade scsi driver. It also modifies asic specific
interface setup to allocate MSIX resources at power on in case of 1860 HW with
no asic block and warns if the asic gen is neither BFI_ASIC_GEN_CT nor
BFI_ASIC_GEN_CT2.
Reported-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

check patch was complaining...mostly replaced:
   if ((ret = asix_foo(xx)) < 0) ...
with
   ret = asix_foo(xx);
   if (ret < 0) ...
Signed-off-by: NGrant Grundler <grundler@chromium.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Asix provided this patch and I've confirmed "Plugable USB2-E1000" and
"Shenzhen Winstars NWU220G" USB dongles can get a link and TX/RX data.
Signed-off-by: N"Freddy Xin" <freddy@asix.com.tw>
Signed-off-by: NGrant Grundler <grundler@chromium.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix phy initialization for AX88772 (USB 2.0 100BT). Failure was
occasionally DHCP wouldn't work after reboot or suspend/resume cycle.

Remove MONITOR_MODE. In this mode, Received packets are not buffered when
the remote wakeup is enabled.
Signed-off-by: N"Freddy Xin" <freddy@asix.com.tw>
Signed-off-by: NGrant Grundler <grundler@chromium.org>
Acked-by: NOlof Johansson <olofj@chromium.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

removing obsoleted sysctl,
ip_rt_gc_interval variable no longer used since 2.6.38
Signed-off-by: NVasily Averin <vvs@sw.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Mostly PHY access and a few (ugly) debug statements for DMA control.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The firmware is cached during the first successful call to open() and
released once the network device is unregistered. The driver uses the
cached firmware between open() and unregister_netdev().

It's similar to 953a12cc but the
firmware is mandatory.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This repairs problem with compile library in userspace (libnl).
Signed-off-by: NJiří Župka <jzupka@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allows ss command (iproute2) to display "ecnseen" if at least one packet
with ECT(0) or ECT(1) or ECN was received by this socket.

"ecn" means ECN was negotiated at session establishment (TCP level)

"ecnseen" means we received at least one packet with ECT fields set (IP
level)

ss -i
...
ESTAB      0      0   192.168.20.110:22  192.168.20.144:38016
ino:5950 sk:f178e400
	 mem:(r0,w0,f0,t0) ts sack ecn ecnseen bic wscale:7,8 rto:210
rtt:12.5/7.5 cwnd:10 send 9.3Mbps rcv_space:14480
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The following commit removed some including headers:
 "net: sh_eth: move the asm/sh_eth.h to include/linux/"
 (commit id: d4fa0e35)

Then, the build failure happened on the linux-next:

drivers/net/ethernet/renesas/sh_eth.c:601: error: 'THIS_MODULE' undeclared here (not in a function)
drivers/net/ethernet/renesas/sh_eth.c:1970: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/renesas/sh_eth.c:1970: warning: data definition has no type or storage class
drivers/net/ethernet/renesas/sh_eth.c:1970: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
drivers/net/ethernet/renesas/sh_eth.c:1970: warning: function declaration isn't a prototype
drivers/net/ethernet/renesas/sh_eth.c:1971: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/renesas/sh_eth.c:1971: warning: data definition has no type or storage class
drivers/net/ethernet/renesas/sh_eth.c:1971: warning: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
drivers/net/ethernet/renesas/sh_eth.c:1971: warning: function declaration isn't a prototype
drivers/net/ethernet/renesas/sh_eth.c:1972: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/renesas/sh_eth.c:1972: warning: data definition has no type or storage class
drivers/net/ethernet/renesas/sh_eth.c:1972: warning: type defaults to 'int' in declaration of 'MODULE_LICENSE'
drivers/net/ethernet/renesas/sh_eth.c:1972: warning: function declaration isn't a prototype

This patch fixes the issue. This patch also get back include/kernel.h
and linux/spinlock.h.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The allocation of "phyinfo" wasn't checked, and also the allocation
wasn't freed on error paths.  Sjur Brændeland pointed out as well
that "phy_driver" should be freed on the error path too.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NSjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Need to allow application to update existing fdb entries that already
exist. This makes bridge netlink neighbor API have same flags and
semantics as ip neighbor table.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When port is added to a bridge, the old code would send the new neighbor
netlink message before the subsequent new link message. This bug makes
it difficult to use the monitoring API in an application.

This code changes the ordering to add the forwarding entry
after the port is setup. One of the error checks (for invalid address)
is moved earlier in the process to avoid having to do unwind.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Also changing it's frequency to once every 64s instead of existing 32s as
it was shown to affect performance
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This was manifesting as a crash when FAT Dump extraction was attempted on a PPC machine.
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This was showing up as junk value on PPC /Big endian machines since
it was marked as a byte.
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add 60s delay before timeout on polling Bit 31 so that FAT dump can
complete when reset occurs.
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Amir Vadai wrote:
> When a stream is paused, and its rule is expired while it is paused,
> no new rule will be configured to the HW when traffic resume.
[...]
> - When stream was resumed, traffic was steered again by RSS, and
> because current-cpu was equal to desired-cpu,  ndo_rx_flow_steer
> wasn't called and no rule was configured to the HW.

Fix this by setting the flow's current CPU only in the table for the
newly selected RX queue.
Reported-and-tested-by: NAmir Vadai <amirv@dev.mellanox.co.il>
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Usually you have to take the bus lock.  Why not here too?

I saw this when working on something else.  Not even compile tested.
Signed-off-by: NDavid Daney <david.daney@cavium.com>
Cc: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Cc: "Uwe Kleine-Konig" <u.kleine-koenig@pengutronix.de>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Accesses to the mdio busses must be done with the mdio_lock to ensure
proper operation.  Conveniently we have the helper function
mdiobus_read() to do that for us.  Lets use it in get_phy_id() instead
of accessing the bus without the lock held.
Signed-off-by: NDavid Daney <david.daney@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/wireless/iwlwifi/iwl-pci.c
	drivers/net/wireless/wl12xx/main.c

Signed-off-by: NGurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change details:
 - Add a callback in the BNA, which is called before sending FW command to stop
   RxQs. After this callback is called, driver should not post anymore Rx
   buffers to the RxQ. This addresses a small window where driver posts Rx
   buffers while FW is stopping/has stopped the RxQ.
 - Registering callback function, rx_stall_cbfn, during bna_rx_create.
   Invoking callback function, rx_stall_cbfn, before sending rx_cfg_clr
   command to FW
 - Bnad_cb_rx_stall implementation - set a flag in the Rxq to mark buffer
   posting disabled state. While posting buffers check for the above flag.
Signed-off-by: NGurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change details:
 - Fix to release soft reset in PLL init for HW
 - Added stats attributes and new bfi msg class
 - Removed some unused code and typo fixes
Signed-off-by: NGurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch enables new HW Brocade 1860. Add BFA_CM_NIC capability mask to
bfa_ioc_attr, Sub-System Device ID Info and support for Brocade 1860 device
ID to bfa_ioc.c and bnad.c.
Signed-off-by: NGurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add new device ID 0x22 and new asic generation BFI_ASIC_GEN_CT2 for 1860.
Implement FW download from user space for new Brocade HW.
Signed-off-by: NGurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add capability map and generic model name scheme for manufacturing block.
Add card types for new HW.

Remove bfa_mfg_is_card_type_valid and ibfa_mfg_adapter_prop_init_flash_ct
macros.
Signed-off-by: NGurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add logic to set ASIC specfic interface in IOC, HW interface initialization
APIs, mode based initialization and MSI-X resource allocation for 1860 with
no asic block. Add new h/w specific register definitions and setup registers
used by IOC logic.

Use normal kernel declaration style, c99 initializers and const for mailbox
structures. Remove unneeded parentheses.
Signed-off-by: NGurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to make USB-to-Ethernet-adapters (depending on usbnet) support
timestamping, the "skb_defer_rx_timestamp" and "skb_tx_timestamp" function
calls are added.
Signed-off-by: NMichael Riesch <michael@riesch.at>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add poll controller function for fec nic.
Signed-off-by: NXiao Jiang <jgq516@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't use hardcoded irq num and replace it with
FEC_IRQ_NUM macro.
Signed-off-by: NXiao Jiang <jgq516@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Noticed that the legacy Interrupt handler didn't have the same
ECC warning as did the MSI.  So this patch adds it.

Signed-off-by: Don Skidmore <donald.c.skidmore>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The X540 thermal sensor interrupt isn't a General Purpose Interrupt
so doesn't need to be enabled in ixgbe_setup_gpie().  Likewise X540 doesn't
use the SDP0 for thermal sensor so it doesn't need to be enabled for any
device other than 82599.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>