There is no reason for the DMA channel program to override the
DMA mode passed down by its caller. Use the passed parameter
directly, and let the caller handle the decision on which mode
is to be used.
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This pin-muxing is best done in the board files. The driver should
not do this explicitly.

Also, this code causes a warning to be thrown when OMAP2430 and OMAP3/4
support are enabled in the same kernel.
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Currently devices don't get detected automatically if the ehci
module is inserted 2nd time onward. We need to disconnect and
reconnect the device for it to get detected and enumerated.

Resetting the USB PHY using PHY reset comamnd over ULPI fixes
this issue. Tested on OMAP3EVM.
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fixes below compilation warning from ulpi.h

include/linux/usb/ulpi.h:145:
        warning: 'struct otg_io_access_ops' declared inside parameter list
include/linux/usb/ulpi.h:145:
         warning: its scope is only this definition or declaration,
         which is probably not what you want
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fixes below compilation warning when host only configuration is
selected.
drivers/usb/musb/musb_core.c: In function 'musb_stage0_irq':
drivers/usb/musb/musb_core.c:711: warning: unused variable 'mbase'
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

DMA_ADDR and DMA_COUNT are 32-bit registers, not 16-bit.

Marking them as 16-bit in the table causes only the lower
16-bits to be dumped and this is misleading.
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Use for_each_pci_dev() to simplify the code.
Signed-off-by: NKulikov Vasiliy <segooon@gmail.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If the write download record failed we shouldn't return 0.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Updated comment to describe why printing macros are needed even
thought they are copied form the composite.h.  Also, made multiline
comments follow the coding standard.
Signed-off-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Here is the patch for the following issue:

drivers/usb/gadget/u_serial.c: In function ‘gs_start_tx’:
drivers/usb/gadget/u_serial.c:369: error: ‘TASK_INTERRUPTIBLE’ undeclared (first use in this function)
drivers/usb/gadget/u_serial.c:369: error: (Each undeclared identifier is reported only once
drivers/usb/gadget/u_serial.c:369: error: for each function it appears in.)
drivers/usb/gadget/u_serial.c: In function ‘gs_rx_push’:
drivers/usb/gadget/u_serial.c:546: error: ‘TASK_INTERRUPTIBLE’ undeclared (first use in this function)
drivers/usb/gadget/u_serial.c: In function ‘gs_close’:
drivers/usb/gadget/u_serial.c:857: error: ‘TASK_INTERRUPTIBLE’ undeclared (first use in this function)
drivers/usb/gadget/u_serial.c:857: error: implicit declaration of function ‘signal_pending’
drivers/usb/gadget/u_serial.c:857: error: implicit declaration of function ‘schedule_timeout’
drivers/usb/gadget/u_serial.c: In function ‘gserial_cleanup’:
drivers/usb/gadget/u_serial.c:1190: error: ‘TASK_UNINTERRUPTIBLE’ undeclared (first use in this function)
drivers/usb/gadget/u_serial.c:1190: error: implicit declaration of function ‘schedule’
drivers/usb/gadget/u_serial.c: In function ‘gserial_disconnect’:
drivers/usb/gadget/u_serial.c:1311: error: ‘TASK_INTERRUPTIBLE’ undeclared (first use in this function)
Signed-off-by: NStephane Duverger <stephane.duverger@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If we use the HCD_LOCAL_MEM flag and dma_declare_coherent_memory() to
enforce the host controller's local memory utilization we also need to
disable native scatter-gather support, otherwise hcd_alloc_coherent() in
map_urb_for_dma() is called with urb->transfer_buffer == NULL, that
triggers a NULL pointer dereference.

We can also consider to add a WARN_ON() and return an error code to
better catch this problem in the future.

At the moment no driver seems to hit this bug, so I should
consider this a low-priority fix.
Signed-off-by: NAndrea Righi <arighi@develer.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Change sizeof(x) / sizeof(*x) to ARRAY_SIZE(x).
Signed-off-by: NKulikov Vasiliy <segooon@gmail.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Don't descend to the EARLY_PRINTK_DBGP directory
unless it is actually used.
Signed-off-by: NNicolas Kaiser <nikai@nikai.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fixed switch, brace, whitespace and spacing coding style issues.
Signed-off-by: NNicolas Kaiser <nikai@nikai.net>
Acked-by: NPete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1386) adds runtime-PM support for PCI-based USB host
controllers.  By default autosuspend is disallowed; the user must
enable it by writing "auto" to the controller's power/control sysfs
attribute.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1396) adds code to uhci-hcd to support the
vendor-specific wakeup settings found in Intel's ICHx hardware.  A
couple of unnecessary memory barriers are removed.  And the root hub
isn't put back into the "suspended" state if power was lost during a
system sleep -- there's not much point in doing so because the root hub
will be resumed shortly.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1395) adds code to hcd_pci_suspend() for handling wakeup
races.  This is another general race pattern, similar to the "open
vs. unregister" race we're all familiar with.  Here, the race is
between suspending a device and receiving a wakeup request from one of
the device's suspended children.

In particular, if a root-hub wakeup is requested at about the same
time as the corresponding USB controller is suspended, and if the
controller is enabled for wakeup, then the controller should either
fail to suspend or else wake right back up again.

During system sleep this won't happen very much, especially since host
controllers generally aren't enabled for wakeup during sleep.  However
it is definitely an issue for runtime PM.  Something like this will be
needed to prevent the controller from autosuspending while waiting for
a root-hub resume to take place.  (That is, in fact, the common case,
for which there is an extra test.)
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1394) adds code to ehci-hcd, ohci-hcd, and uhci-hcd for
automatically resuming the root hub when the controller is resumed, if
the root hub has a wakeup request pending on some port.

During resume from system sleep this doesn't matter, because the root
hubs will naturally be resumed along with every other device in the
system.  However it _will_ matter for runtime PM: If the controller is
suspended and a remote wakeup request is received then the controller
will autoresume, but we need to ensure that the root hub also
autoresumes.  Otherwise the wakeup request would be ignored, the
controller would go back to sleep, and the cycle would repeat a large
number of times (I saw this happen before the patch was written).
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1385) adds a "do_wakeup" parameter to the pci_suspend
method used by PCI-based host controller drivers.  ehci-hcd in
particular needs to know whether or not to enable wakeup when
suspending a controller.  Although that information is currently
available through device_may_wakeup(), when support is added for
runtime suspend this will no longer be true.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1384) moves the resume_common() routine in hcd-pci.c a
little higher in the source file to avoid forward references in an
upcoming patch.  It also replaces the "hibernated" argument with a
more general "event" argument, which will be useful when the routine
is called during a runtime resume.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1383) takes the powermac-specific code from the PCI HCD
glue layer and encapsulates it in its own subroutine.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This commit cleans the g_fs gadget hopefully making it more
readable.  This is achieved by usage of the usb_string_ids_tab()
function for batch string IDs registration as well as
generalising configuration so that a single routine is
used to add each configuration and bind interfaces.  As an
effect, the code is shorter and has fewer #ifdefs.

Moreover, in some circumstances previous code #defined
CONFIG_USB_FUNCTIONFS_GENERIC macro to prevent a situation
where gadget with no configurations is built.  This code removes
the #define form source code and achieves the same effect using
select in Kconfig.

This patch also changes wording and names of the Kconfig options.
Signed-off-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1393) converts several of the single-bit fields in
struct usb_hcd to atomic flags.  This is for safety's sake; not all
CPUs can update bitfield values atomically, and these flags are used
in multiple contexts.

The flag fields that are set only during registration or removal can
remain as they are, since non-atomic accesses at those times will not
cause any problems.

(Strictly speaking, the authorized_default flag should become atomic
as well.  I didn't bother with it because it gets changed only via
sysfs.  It can be done later, if anyone wants.)
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In may gadgets bind and bind like functions were in a init section
as they were only run during initialisation.  However, being
callback functions they were referenced from structures in “normal”
sections.  Changing the tag from “__init” to “__ref” fixes the
warnings.
Signed-off-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Added pre_eject() and post_eject() callbacks which are
called before and after removable logical unit is ejected.
The first can prevent logical unit from being ejected.

This commit also changes the way callbacks are passed to
the function from gadget.  A fsg_operations structure has
been created which lists all callbacks -- this is passed
to the fsg_config.

This is important because it changes the way thread_exits()
callback is passed.
Signed-off-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Added a disconnect() callback to composite devices which
is called by composite glue when its disconnect callback
is called by gadget.
Signed-off-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

A short documentation of the g_multi driver along with INF
files for Windows XP SP3 are provided.
Signed-off-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Updated the INF file for g_serial gadget.  It should work with
most recent Windows systems now.
Signed-off-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Updated the INF file for the g_ether gadget.  It should work with most
recent Windows systems now.
Signed-off-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The Multifunction Composite Gadget have been cleaned up
and refactored so hopefully it looks prettier and works
at least as good as before changes.

A Kconfig has also been fixed to make it impossible to build
FunctionFS gadget with no configurations.  With this patch, if
RNDIS is not chosen by the user CDC is force-selected.
Signed-off-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The ep0req_name was never used in f_mass_storage hence it may
be safely removed from the code.  It was a leftover from File
Storage Gadget which used it for debug messages.
Signed-off-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Use usb_string_ids_n() function to simplify string ids
registeration.
Signed-off-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

usb_string_ids_tab() and usb_string_ids_n() functions added to
the composite framework.  The first accepts an array of
usb_string object and for each registeres a string id and the
second registeres a given number of ids and returns the first.

This may simplify string ids registration since gadgets and
composite functions won't have to call usb_string_id() several
times and each time check for errer status -- all this will be
done with a single call.
Signed-off-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

FunctionFS had a bit unique name for function used to add it
to USB configuration.  Renamed as to match naming convention
of other functions.
Signed-off-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Mass Storage Function had a bit unique name for function
used to add it to USB configuration.  Renamed as to match
naming convention of other functions.
Signed-off-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch changes msg_do_config() function so that it uses
a static object for a fsg_common structure instead of dynamically
allocated.  This is a micro-optimisation.
Signed-off-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

compat_ioctl does not use the BKL, so I assume that
the native function does not need it either.

The open function is already protected by the
driver's mutex, the BKL is probably not needed
here either.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

There is no gadget driver in the tree that
actually implements the ioctl operation, so
obviously it is not necessary to hold the
BKL around the call.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Michał Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

BKL was not really needed, just came from earlier push downs.

The only part that's a bit dodgy is the lseek function. Would
need another lock or atomic access to fpos on 32bit?
Better to have a libfs lseek
Signed-off-by: NAndi Kleen <ak@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The usb serial driver initialization tried to use the BKL to stop
driver modules from unloading, but that didn't work anyways.

There was already some code to do proper try_module_get,
but it was conditional on having a new probe interface.
I checked all the low level drivers and they all have proper
.owner = THIS_MODULE, so it's ok to always use.

The other problem was the usb_serial_driver_list needing
protection by a lock. This was broken anyways because unregister
did not necessarily have the BKL.

I extended the extending table_lock mutex to protect this case too.

With these changes the BKL can be removed here.
Signed-off-by: NAndi Kleen <ak@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>