Add a sanity check to ensure that all requested channel sizes are within
bounds, which should reduce errors in driver implementation.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ethernet drivers implementing both {GS}RXFH and {GS}CHANNELS ethtool ops
incorrectly allow SCHANNELS when it would conflict with the settings
from SRXFH. This occurs because it is not possible for drivers to
understand whether their Rx flow indirection table has been configured
or is in the default state. In addition, drivers currently behave in
various ways when increasing the number of Rx channels.

Some drivers will always destroy the Rx flow indirection table when this
occurs, whether it has been set by the user or not. Other drivers will
attempt to preserve the table even if the user has never modified it
from the default driver settings. Neither of these situation is
desirable because it leads to unexpected behavior or loss of user
configuration.

The correct behavior is to simply return -EINVAL when SCHANNELS would
conflict with the current Rx flow table settings. However, it should
only do so if the current settings were modified by the user. If we
required that the new settings never conflict with the current (default)
Rx flow settings, we would force users to first reduce their Rx flow
settings and then reduce the number of Rx channels.

This patch proposes a solution implemented in net/core/ethtool.c which
ensures that all drivers behave correctly. It checks whether the RXFH
table has been configured to non-default settings, and stores this
information in a private netdev flag. When the number of channels is
requested to change, it first ensures that the current Rx flow table is
not going to assign flows to now disabled channels.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need that for a custom hardware that needs the reverse reset
sequence.
Signed-off-by: NBernhard Walle <bernhard@bwalle.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: phy: bcm7xxx: Misc cleanups

These two patches are cleanups to the BCM7xxx internal PHY driver:

- fix a constant name missing a X (as in BCM7XXX)
- add a macro to reduce the amount of code duplication to add new entries
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce a macro which helps adding new 40NM EPHY entries and reduces the
amount of boilerplate code.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver is BCM7xxx, we were missing an additional X in the constant naming,
fix that to be consistent.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Edward Cree says:

====================
Local Checksum Offload

Re-tested VxLAN; everything else is unchanged from v4.

Changes from v4:
 * Rebased series to fix conflicts with vxlan/vxlan6 merge.

Changes from v3:
 * Fixed inverted checksum values introduced in v3.
 * Don't mangle zero checksums in GRE.
 * Clear skb->encapsulation in iptunnel_handle_offloads when not using
   CHECKSUM_PARTIAL, lest drivers incorrectly interpret that as a request
   for inner checksum offload.

Changes from v2:
 * Added support for IPv4 GRE.
 * Split out 'always set up for checksum offload' into its own patch.
 * Removed csum_help from iptunnel_handle_offloads.
 * Rewrote LCO callers to only fold once.
 * Simplified nocheck handling.

Changes from v1:
 * Enabled support in more encapsulation protocols.
   I think it now covers everything except GRE.
 * Wrote up some documentation covering TX checksum offload, LCO and RCO.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All users now pass false, so we can remove it, and remove the code that
 was conditional upon it.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The only protocol affected at present is Geneve.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the dst device doesn't support it, it'll get fixed up later anyway
 by validate_xmit_skb().  Also, this allows us to take advantage of LCO
 to avoid summing the payload multiple times.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The arithmetic properties of the ones-complement checksum mean that a
 correctly checksummed inner packet, including its checksum, has a ones
 complement sum depending only on whatever value was used to initialise
 the checksum field before checksumming (in the case of TCP and UDP,
 this is the ones complement sum of the pseudo header, complemented).
Consequently, if we are going to offload the inner checksum with
 CHECKSUM_PARTIAL, we can compute the outer checksum based only on the
 packed data not covered by the inner checksum, and the initial value of
 the inner checksum field.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Eric Dumazet says:

====================
tcp/dccp: better use of ephemeral ports

Big servers have bloated bind table, making very hard to succeed
ephemeral port allocations, without special containers/namespace tricks.

This patch series extends the strategy added in commit 07f4c900
("tcp/dccp: try to not exhaust ip_local_port_range in connect()").

Since ports used by connect() are much likely to be shared among them,
we give a hint to both bind() and connect() to keep the crowds separated
if possible.

Of course, if on a specific host an application needs to allocate ~30000
ports using bind(), it will still be able to do so. Same for ~30000 connect()
to a unique 2-tuple (dst addr, dst port)

New implemetation is also more friendly to softirqs and reschedules.

v2: rebase after TCP SO_REUSEPORT changes
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement strategy used in __inet_hash_connect() in opposite way :

Try to find a candidate using odd ports, then fallback to even ports.

We no longer disable BH for whole traversal, but one bucket at a time.
We also use cond_resched() to yield cpu to other tasks if needed.

I removed one indentation level and tried to mirror the loop we have
in __inet_hash_connect() and variable names to ease code maintenance.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit 07f4c900 ("tcp/dccp: try to not exhaust ip_local_port_range
in connect()"), I added a very simple heuristic, so that we got better
chances to use even ports, and allow bind() users to have more available
slots.

It gave nice results, but with more than 200,000 TCP sessions on a typical
server, the ~30,000 ephemeral ports are still a rare resource.

I chose to go a step further, by looking at all even ports, and if none
was available, fallback to odd ports.

The companion patch does the same in bind(), but in opposite way.

I've seen exec times of up to 30ms on busy servers, so I no longer
disable BH for the whole traversal, but only for each hash bucket.
I also call cond_resched() to be gentle to other tasks.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jesper Dangaard Brouer says:

====================
net: mitigating kmem_cache free slowpath

This patchset is the first real use-case for kmem_cache bulk _free_.
The use of bulk _alloc_ is NOT included in this patchset. The full use
have previously been posted here [1].

The bulk free side have the largest benefit for the network stack
use-case, because network stack is hitting the kmem_cache/SLUB
slowpath when freeing SKBs, due to the amount of outstanding SKBs.
This is solved by using the new API kmem_cache_free_bulk().

Introduce new API napi_consume_skb(), that hides/handles bulk freeing
for the caller.  The drivers simply need to use this call when freeing
SKBs in NAPI context, e.g. replacing their calles to dev_kfree_skb() /
dev_consume_skb_any().

Driver ixgbe is the first user of this new API.

[1] http://thread.gmane.org/gmane.linux.network/384302/focus=397373
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is an opportunity to bulk free SKBs during reclaiming of
resources after DMA transmit completes in ixgbe_clean_tx_irq.  Thus,
bulk freeing at this point does not introduce any added latency.

Simply use napi_consume_skb() which were recently introduced.  The
napi_budget parameter is needed by napi_consume_skb() to detect if it
is called from netpoll.

Benchmarking IPv4-forwarding, on CPU i7-4790K @4.2GHz (no turbo boost)
 Single CPU/flow numbers: before: 1982144 pps ->  after : 2064446 pps
 Improvement: +82302 pps, -20 nanosec, +4.1%
 (SLUB and GCC version 5.1.1 20150618 (Red Hat 5.1.1-4))

Joint work with Alexander Duyck.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The network stack defers SKBs free, in-case free happens in IRQ or
when IRQs are disabled. This happens in __dev_kfree_skb_irq() that
writes SKBs that were free'ed during IRQ to the softirq completion
queue (softnet_data.completion_queue).

These SKBs are naturally delayed, and cleaned up during NET_TX_SOFTIRQ
in function net_tx_action().  Take advantage of this a use the skb
defer and flush API, as we are already in softirq context.

For modern drivers this rarely happens. Although most drivers do call
dev_kfree_skb_any(), which detects the situation and calls
__dev_kfree_skb_irq() when needed.  This due to netpoll can call from
IRQ context.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Discovered that network stack were hitting the kmem_cache/SLUB
slowpath when freeing SKBs.  Doing bulk free with kmem_cache_free_bulk
can speedup this slowpath.

NAPI context is a bit special, lets take advantage of that for bulk
free'ing SKBs.

In NAPI context we are running in softirq, which gives us certain
protection.  A softirq can run on several CPUs at once.  BUT the
important part is a softirq will never preempt another softirq running
on the same CPU.  This gives us the opportunity to access per-cpu
variables in softirq context.

Extend napi_alloc_cache (before only contained page_frag_cache) to be
a struct with a small array based stack for holding SKBs.  Introduce a
SKB defer and flush API for accessing this.

Introduce napi_consume_skb() as replacement for e.g. dev_consume_skb_any()
when running in NAPI context.  A small trick to handle/detect if we
are called from netpoll is to see if budget is 0.  In that case, we
need to invoke dev_consume_skb_irq().

Joint work with Alexander Duyck.
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Nikolay Aleksandrov says:

====================
virtio_net: better ethtool setting validation

This small set is a follow-up for the recent patches that added ethtool
get/set settings. Patch 1 changes the speed validation routine to check
if the speed is between 0 and INT_MAX (or SPEED_UNKNOWN) and patch 2 adds
port validation to virtio_net and better validation comment.

This set is on top of Michael's patch which explains that speeds from 0
to INT_MAX are valid:
http://patchwork.ozlabs.org/patch/578911/
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We should validate the port setting that we got from the user and check
if it's what we've set it to (PORT_OTHER), also add explanation that
ignoring advertising is good as long as we don't have autonegotiation.
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Devices these days can have any speed and as was recently pointed out
any speed from 0 to INT_MAX is valid so adjust speed validation to
accept such values.
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Andrew F. Davis says:

====================
net: phy: dp83848: Add support for TI TLK10x Ethernet PHYs

This series is [0] split into its logical components.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAndrew F. Davis <afd@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The TI TLK10x Ethernet PHYs are similar in the interrupt relevant
registers and so are compatible with the DP83848x devices already
supported.
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reorganize code by moving the desired interrupt mask definition
out of function. Also rearrange the enable/disable interrupt function
to prevent accidental over-writing of values in registers.
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After acquiring National Semiconductor, TI appears to have
changed the Vendor Model Number for the DP83848C PHYs,
add this new ID to supported IDs.
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a helper macro for defining dp83848 compatible phy devices.
Update copyright info.
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The EVB (virtual bridge) functionality should be disabled on older BE3
and Lancer chips if SR-IOV is disabled in the NIC's BIOS. This setting
is identified by the zero value of total VFs reported by the card.
The GET_HSW_CONFIG command cannot be used as it is not supported by
these older chipset's FW.

v2: added the comment

Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Padmanabh Ratnakar <padmanabh.ratnakar@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Acked-by: NSathya Perla <sathya.perla@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Helmut Buchsbaum says:

====================
Add support for MICREL KSZ8795CLX 5-port switch

This patch series refactors the spi-ks8995 driver to finally add support
for the MICREL KSZ8795CLX. Additionally support for controlling a GPIO
line for resetting the switch is added.

Helmut

Changes since v2:
 - use GPIO_ACTIVE_LOW according to Andrew's remark.
 - use ePAPR compliant node name in example, thanks to Sergei for
   pointing out
Changes since v1:
 - removed initializing registers from Device Tree following Florian's
   advice
 - fixed GPIO handling for reset according to Andrew's remark.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHelmut Buchsbaum <helmut.buchsbaum@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for MICREL KSZ8795CLX Integrated 5-Port, 10-/100-Managed
Ethernet Switch with Gigabit GMII/RGMII and MII/RMII interfaces.
Signed-off-by: NHelmut Buchsbaum <helmut.buchsbaum@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prepare creating SPI reads and writes for other switch families.
The KS8995 family uses the straight forward
	<8bit CMD><8bit ADDR>
sequence.
To be able to support KSZ8795 family, which uses
	<3bit CMD><12bit ADDR><1 bit TR>
make the SPI command creation chip variant dependent.
Signed-off-by: NHelmut Buchsbaum <helmut.buchsbaum@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When using device tree it is no more possible to reset the PHY at board
level. Furthermore, doing in the driver allows to power down the switch
when it is not used any more.

The patch introduces a new optional property "reset-gpios" denoting an
appropriate GPIO handle, e.g.:

reset-gpios = <&gpio0 46 GPIO_ACTIVE_LOW>
Signed-off-by: NHelmut Buchsbaum <helmut.buchsbaum@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the chip variant is now determined by spi_device_id, verify
family and chip id and determine the revision id.
Signed-off-by: NHelmut Buchsbaum <helmut.buchsbaum@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Refactor to use spi_device_id table to facilitate easy
extendability.
Signed-off-by: NHelmut Buchsbaum <helmut.buchsbaum@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sunil Goutham says:

====================
net: thunderx: Setting IRQ affinity hints and other optimizations

This patch series contains changes
- To add support for virtual function's irq affinity hint
- Replace napi_schedule() with napi_schedule_irqoff()
- Reduce page allocation overhead by allocating pages
  of higher order when pagesize is 4KB.
- Add couple of stats which helps in debugging
- Some miscellaneous changes to BGX driver.

Changes from v1:
- As suggested changed MAC address invalid log message
  to dev_err() instead of dev_warn().
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>