I see no override of read/write callbacks in sdhci-of-at91.c.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

On NI 9037 boards the max SDIO frequency is limited by trace lengths
and other layout choices. The max SDIO frequency is stored in an ACPI
table.

The driver reads the ACPI entry MXFQ during sdio_probe_slot and sets the
f_max field of the host.
Signed-off-by: NNathan Sullivan <nathan.sullivan@ni.com>
Reviewed-by: NJaeden Amero <jaeden.amero@ni.com>
Reviewed-by: NJosh Cartwright <joshc@ni.com>
Signed-off-by: NZach Brown <zach.brown@ni.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add PCI ID for Intel byt sdio host controller sub-vended by NI.

The controller has different behavior because of the board layout NI
puts it on.
Signed-off-by: NZach Brown <zach.brown@ni.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Before calling clk_round_rate(), put the spin_unlock_irq() in
sdhci_s3c_consider_clock() function.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

When card is polling (broken-cd), there is a spamming messge related to
clock.
After applied this patch, display the message only one time at boot
time. It's enough to check which clock values is used.
Also prevent to display the spamming message.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

If card is polling or non-removable, display the more exact message.
It's helpful to debug which detecting scheme is using.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Before checking flags, it has to check "present" variable.
Otherwise, flags should be cleared everytime.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The commit 64997de4fd17 ("mmc: dw_mmc: remove system PM callback") is
missing to call dw_mci_ctrl_reset(). This adds to call
dw_mci_ctrl_reset() and to handle error of clocks.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The dw_mmc-exynos should be RPM_ACTIVE on probe() to call suspend
callback of runtime PM in pm_runtime_force_suspend() during first system
suspend. Also call pm_runtime_get_noresume() on probe() because it
doesn't call suspend/resume callback by runtime PM now.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

It is unnecessary to panic the kernel when testing mmc. Instead,
cast a warning for folkz to debug and return the error code to
the caller to indicate the failure of this test should be enough.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

bounce_sg for mqrq_cur and mqrq_pre are proper
allocated when initializing the queue and will not
be freed before explicitly cleaning the queue. So from
the code itself it should be quite confident to remove
this check. If that BUG_ON take effects, it is mostly
likely the memory is randomly oopsing.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The code seems quite simple to maintain the sdio_uart_table,
and the insert/remove port from the table are symmetric. If
the BUG_ON occurs, which means serial_core modify the index
or mess up the port sequence anyway.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

BUG_ONs doesn't help anything except for stop the system from
running. If it occurs, it implies we should deploy proper error
handling for that. So this patch is gonna discard these meaningless
BUG_ONs and deploy error handling if needed.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

BUG_ONs doesn't help anything except for stop the system from
running. If it occurs, it implies we should deploy proper error
handling for that. So this patch is gonna discard these meaningless
BUG_ONs and deploy error handling if needed.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

BUG_ONs doesn't help anything except for stop the system from
running. If it occurs, it implies we should deploy proper error
handling for that. So this patch is gonna discard these meaningless
BUG_ONs and deploy error handling if needed.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Return error value for file_operations callback instead
of triggering BUG_ON which is meaningless. Personally I
don't believe n != EXT_CSD_STR_LEN could happen. Anyway,
propagate the error to the caller.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

BUG_ONs doesn't help anything except for stop the system from
running. If it occurs, it implies we should deploy proper error
handling for that. So this patch is gonna discard these meaningless
BUG_ONs and deploy error handling if needed.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add definitions relating to Command Queuing.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add a mmc_queue member to record the size of the queue, which currently
supports 2 requests on-the-go at a time. Instead of allocating resources
for 2 slots in the queue, allow for an arbitrary number.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

In preparation for supporting a queue of requests, factor out
mmc_queue_reqs_free_bufs().
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Reviewed-by: NHarjani Ritesh <riteshh@codeaurora.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

In preparation for supporting a queue of requests, factor out
mmc_queue_alloc_sgs().
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Reviewed-by: NHarjani Ritesh <riteshh@codeaurora.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

In preparation for supporting a queue of requests, factor out
mmc_queue_alloc_bounce_sgs().
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Reviewed-by: NHarjani Ritesh <riteshh@codeaurora.org>
[Ulf: Fixed compiler warning]
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

In preparation for supporting a queue of requests, factor out
mmc_queue_alloc_bounce_bufs().
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Reviewed-by: NHarjani Ritesh <riteshh@codeaurora.org>
[Ulf: Fixed compiler warning]
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The only time the driver sleeps expecting to be woken upon the arrival of
a new request, is when the dispatch queue is empty. The only time that it
is known whether the dispatch queue is empty is after NULL is returned
from blk_fetch_request() while under the queue lock.

Recognizing those facts, simplify the synchronization between the queue
thread and the request function. A couple of flags tell the request
function what to do, and the queue lock and barriers associated with
wake-ups ensure synchronization.

The result is simpler and allows the removal of the context_info lock.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Reviewed-by: NHarjani Ritesh <riteshh@codeaurora.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The 4K native sector check does not allow for the 'do' loop nor the
variables used after the 'cmd_abort' label.

'brq' and 'req' get reassigned in the 'do' loop, so the check must not
assume what their values are. After the 'cmd_abort' label, 'mq_rq' and
'req' are used, but 'rqc' must be NULL otherwise it can be started again.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>

We get the following warning with the driver is compiled in:

WARNING: modpost: Found 1 section mismatch(es).
To see full details build your kernel with:
'make CONFIG_DEBUG_SECTION_MISMATCH=y'

With CONFIG_DEBUG_SECTION_MISMATCH enabled, the details are reported:

WARNING: vmlinux.o(.text+0x55d014): Section mismatch in reference from the
function fsl_guts_probe() to the function
.init.text:of_flat_dt_get_machine_name()
The function fsl_guts_probe() references
the function __init of_flat_dt_get_machine_name().
This is often because fsl_guts_probe lacks a __init
annotation or the annotation of of_flat_dt_get_machine_name is wrong.

This patch fixes the issue by using the normal DT/OF API rather than
the of_flat_* one.

Cc: Scott Wood <oss@buserror.net>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NSudeep Holla <sudeep.holla@arm.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The eSDHC of T4240-R1.0-R2.0 has incorrect vender version and spec version.
Acturally the right version numbers should be VVN=0x13 and SVN = 0x1.
This patch adds the GUTS driver support for eSDHC driver to match SoC.
And fix host version to avoid that incorrect version numbers break down
the ADMA data transfer.
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Acked-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NScott Wood <oss@buserror.net>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add maintainer entry for Freescale SoC drivers including
the QE library and the GUTS driver now. Also add maintainer
for QE library.
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Acked-by: NScott Wood <oss@buserror.net>
Acked-by: NQiang Zhao <qiang.zhao@nxp.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The global utilities block controls power management, I/O device
enabling, power-onreset(POR) configuration monitoring, alternate
function selection for multiplexed signals,and clock control.

This patch adds a driver to manage and access global utilities block.
Initially only reading SVR and registering soc device are supported.
Other guts accesses, such as reading RCW, should eventually be moved
into this driver as well.
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Move guts devicetree doc to Documentation/devicetree/bindings/soc/fsl/
since it's used by not only PowerPC but also ARM. And add a specification
for 'little-endian' property.
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Acked-by: NRob Herring <robh@kernel.org>
Acked-by: NScott Wood <oss@buserror.net>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add the dts node for device configuration unit that provides
general purpose configuration and status for the device.
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Acked-by: NScott Wood <oss@buserror.net>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Merge the immutable soc-device-match-tag1 provided by Geert Uytterhoeven
to pull in the new soc_device_match() interface for matching against
soc_bus attributes.

Simply document new compatibility strings as the driver is already
activated using a fallback compatibility string.

These compat strings are in keeping with those for all other
Renesas ARM based SoCs with sh_mmcif enabled in mainline.
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Remove documentation of support for the SH7372 (SH-Mobile AP4) from the MMC
driver. The driver itself appears to have no SH7372 specific code.

Commit edf41009 ("ARM: shmobile: sh7372 dtsi: Remove Legacy file")
removes this SoC from the kernel in v4.1.
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

I've had it with this code now.

The packed command support is a complex hurdle in the MMC/SD block
layer, around 500+ lines of code which was introduced in 2013 in

commit ce39f9d1 ("mmc: support packed write command for eMMC4.5
devices")
commit abd9ac14 ("mmc: add packed command feature of eMMC4.5")

...and since then it has been rotting. The original author of the
code has disappeared from the community and the mail address is
bouncing.

For the code to be exercised the host must flag that it supports
packed commands, so in mmc_blk_prep_packed_list() which is called for
every single request, the following construction appears:

u8 max_packed_rw = 0;

if ((rq_data_dir(cur) == WRITE) &&
    mmc_host_packed_wr(card->host))
        max_packed_rw = card->ext_csd.max_packed_writes;

if (max_packed_rw == 0)
    goto no_packed;

This has the following logical deductions:

- Only WRITE commands can really be packed, so the solution is
  only half-done: we support packed WRITE but not packed READ.
  The packed command support has not been finalized by supporting
  reads in three years!

- mmc_host_packed_wr() is just a static inline that checks
  host->caps2 & MMC_CAP2_PACKED_WR. The problem with this is
  that NO upstream host sets this capability flag! No driver
  in the kernel is using it, and we can't test it. Packed
  command may be supported in out-of-tree code, but I doubt
  it. I doubt that the code is even working anymore due to
  other refactorings in the MMC block layer, who would
  notice if patches affecting it broke packed commands?
  No one.

- There is no Device Tree binding or code to mark a host as
  supporting packed read or write commands, just this flag
  in caps2, so for sure there are not any DT systems using
  it either.

It has other problems as well: mmc_blk_prep_packed_list() is
speculatively picking requests out of the request queue with
blk_fetch_request() making the MMC/SD stack harder to convert
to the multiqueue block layer. By this we get rid of an
obstacle.

The way I see it this is just cruft littering the MMC/SD
stack.

Cc: Namjae Jeon <namjae.jeon@samsung.com>
Cc: Maya Erez <qca_merez@qca.qualcomm.com>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The void (*pre_req) callback in the struct mmc_host_ops vtable
is passing an argument "is_first_req" indicating whether this is
the first request or not.

None of the in-kernel users use this parameter: instead, since
they all just do variants of dma_map* they use the DMA cookie
to indicate whether a pre* callback has already been done for
a request when they decide how to handle it.

Delete the parameter from the callback and all users, as it is
just pointless cruft.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

According to the JEDEC specification, during bus timing change operations
for mmc, sending a CMD13 could trigger CRC errors.

As switching to HS DDR mode indeed causes a bus timing change, polling with
CMD13 to detect card busy, may thus potentially trigger CRC errors.
Currently these errors are treated as the switch to HS DDR mode failed.

To improve this behaviour, let's instead tell __mmc_switch() to retry when
it encounters CRC errors during polling.

Moreover, when switching to HS DDR mode, let's make sure the CMD13 polling
is done by having the mmc host and the mmc card, being configured to
operate at the same selected bus speed timing. Fix this by providing
MMC_TIMING_MMC_DDR52 as the timing parameter to __mmc_switch().
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>

In cases when the mmc host doesn't support HW busy detection, polling for a
card being busy by using CMD13 is beneficial. That is because, instead of
waiting a fixed amount of time, 500ms or the generic CMD6 time from
EXT_CSD, we find out a lot sooner when the card stops signaling busy. This
leads to a significant decreased total initialization time for the mmc
card.

However, to allow polling with CMD13 during a bus timing change operation,
such as switching to HS mode, we first need to update the mmc host's bus
timing before starting to poll. Deal with that, simply by providing
MMC_TIMING_MMC_HS as the timing parameter to __mmc_switch() from
mmc_select_hs().

By telling __mmc_switch() to allow polling with CMD13, also makes it
validate the CMD6 status, thus we can remove the corresponding checks.

When switching to HS400ES, the mmc_select_hs() function is called in one of
the intermediate steps. To still prevent CMD13 polling for HS400ES, let's
call the __mmc_switch() function in this path as it enables us to keep
using the existing method.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>

In cases when a speed mode change is requested for mmc cards, a CMD6 is
sent by calling __mmc_switch() during the card initialization. The CMD6
leads to the card entering a busy period. When that is completed, the host
must parse the CMD6 status to find out whether the change of the speed mode
succeeded.

To enable the mmc core to poll the card by using CMD13 to find out when the
busy period is completed, it's reasonable to make sure polling is done by
having the mmc host and the mmc card, being configured to operate at the
same selected bus speed timing.

Therefore, let's extend __mmc_switch() to take yet another parameter, which
allow its callers to update the bus speed timing of the mmc host. In this
way, __mmc_switch() also becomes capable of reading and validating the CMD6
status by sending a CMD13, in cases when that's desired.

If __mmc_switch() encounters a failure, we make sure to restores the old
bus speed timing for the mmc host, before propagating the error code.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>