Take a page from the powerpc folks and just calculate the
delay factor directly.

Since frequency scaling chips use a system-tick register,
the value is going to be the same system-wide.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the move of ldom_startcpu_cpuid() into smp.c some other
things need to follow along:

1) smp.c is not a driver so we can't use "PFX" macro in the
   printk calls.

2) smp.c now needs asm/io.h and asm/hvtramp.h, ds.c no longer
   does

3) kimage_addr_to_ra() also needs to move into smp.c

While we're here, update copyright info and my email address
in smp.c
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do not select HOTPLUG_CPU from SUN_LDOMS, that causes
HOTPLUG_CPU to be selected even on non-SMP which is
illegal.

Only build hvtramp.o when SMP, just like trampoline.o

Protect dr-cpu code in ds.c with HOTPLUG_CPU.

Likewise move ldom_startcpu_cpuid() to smp.c and protect
it and the call site with SUN_LDOMS && HOTPLUG_CPU.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The VIO drivers register themselves unconditionally just
like those of any other bus type, so to avoid crashes
on non-VIO systems we need to always register vio_bus_type.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Only adding cpus is supports at the moment, removal
will come next.

When new cpus are configured, the machine description is
updated.  When we get the configure request we pass in a
cpu mask of to-be-added cpus to the mdesc CPU node parser
so it only fetches information for those cpus.  That code
also proceeds to update the SMT/multi-core scheduling bitmaps.

cpu_up() does all the work and we return the status back
over the DS channel.

CPUs via dr-cpu need to be booted straight out of the
hypervisor, and this requires:

1) A new trampoline mechanism.  CPUs are booted straight
   out of the hypervisor with MMU disabled and running in
   physical addresses with no mappings installed in the TLB.

   The new hvtramp.S code sets up the critical cpu state,
   installs the locked TLB mappings for the kernel, and
   turns the MMU on.  It then proceeds to follow the logic
   of the existing trampoline.S SMP cpu bringup code.

2) All calls into OBP have to be disallowed when domaining
   is enabled.  Since cpus boot straight into the kernel from
   the hypervisor, OBP has no state about that cpu and therefore
   cannot handle being invoked on that cpu.

   Luckily it's only a handful of interfaces which can be called
   after the OBP device tree is obtained.  For example, rebooting,
   halting, powering-off, and setting options node variables.

CPU removal support will require some infrastructure changes
here.  Namely we'll have to process the requests via a true
kernel thread instead of in a workqueue.  workqueues run on
a per-cpu thread, but when unconfiguring we might need to
force the thread to execute on another cpu if the current cpu
is the one being removed.  Removal of a cpu also causes the kernel
to destroy that cpu's workqueue running thread.

Another issue on removal is that we may have interrupts still
pointing to the cpu-to-be-removed.  So new code will be needed
to walk the active INO list and retarget those cpus as-needed.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a special domain services capability for setting
variables in the OBP options node.  Guests don't have permanent
store for the OBP variables like a normal system, so they are
instead maintained in the LDOM control node or in the SC.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Property values cannot be referenced outside of
mdesc_grab()/mdesc_release() pairs.  The only major
offender was the VIO bus layer, easily fixed.

Add some commentary to mdesc.h describing these rules.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since we have to be able to handle MD updates, having an in-tree
set of data structures representing the MD objects actually makes
things more painful.

The MD itself is easy to parse, and we can implement the existing
interfaces using direct parsing of the MD binary image.

The MD is now reference counted, so accesses have to now take the
form:

	handle = mdesc_grab();

	... operations on MD ...

	mdesc_release(handle);

The only remaining issue are cases where code holds on to references
to MD property values.  mdesc_get_property() returns a direct pointer
to the property value, most cases just pull in the information they
need and discard the pointer, but there are few that use the pointer
directly over a long lifetime.  Those will be fixed up in a subsequent
changeset.

A preliminary handler for MD update events from domain services is
there, it is rudimentry but it works and handles all of the reference
counting.  It does not check the generation number of the MDs,
and it does not generate a "add/delete" list for notification to
interesting parties about MD changes but that will be forthcoming.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All of the interrupts say "LDX RX" and "LDX TX" currently
which is next to useless.  Put a device specific prefix
before "RX" and "TX" instead which makes it much more
useful.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Besides the existing usage for power-button interrupts, we'll
want to make use of this code for domain-services where the
LDOM manager can send reboot requests to the guest node.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

They sit under the root of the MD tree unlike the rest of
the LDC channel based virtual devices.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1) LDC_MODE_RELIABLE is deprecated an unused by anything, plus
   it and LDC_MODE_STREAM were mis-numbered.

2) read_stream() should try to read as much as possible into
   the per-LDC stream buffer area, so do not trim the read_nonraw()
   length by the caller's size parameter.

3) Send data ACKs when necessary in read_nonraw().

4) In read_nonraw() when we get a pure ACK, advance the RX head
   unconditionally past it.

5) Provide the ACKID field in the ldcdgb() packet dump in read_nonraw().
   This helps debugging stream mode LDC channel problems.

6) Decrease verbosity of rx_data_wait() so that it is more useful.
   A debugging message each loop iteration is too much.

7) In process_data_ack() stop the loop checking when we hit lp->tx_tail
   not lp->tx_head.

8) Set the seqid field properly in send_data_nack().
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is also a partial workaround for a bug in the LDOM firmware which
double-transmits RX inos during high load.  Without this, such an
event causes the kernel to loop forever in the interrupt call chain
ACK'ing but never actually running the IRQ handler (and thus clearing
the interrupt condition in the device).

There is still a bad potential effect when double INOs occur,
not covered by this changeset.  Namely, if the INO is already on
the per-cpu INO vector list, we still blindly re-insert it and
thus we can end up losing interrupts already linked in after
it.

We could deal with that by traversing the list before insertion,
but that's too expensive for this edge case.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Virtual devices on Sun Logical Domains are built on top
of a virtual channel framework.  This, with help of hypervisor
interfaces, provides a link layer protocol with basic
handshaking over which virtual device clients and servers
communicate.

Built on top of this is a VIO device protocol which has it's
own handshaking and message types.  At this layer attributes
are exchanged (disk size, network device addresses, etc.)
descriptor rings are registered, and data transfers are
triggers and replied to.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* git://git.infradead.org/battery-2.6:
  git-battery vs git-acpi
  Power supply class and drivers: remove non obligatory return statements
  pda_power: clean up irq, timer
  MAINTAINERS: Add maintainers for power supply subsystem and drivers

Fixed up trivial conflict in drivers/w1/slaves/w1_ds2760.c manually

* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (166 commits)
  [SCSI] ibmvscsi: convert to use the data buffer accessors
  [SCSI] dc395x: convert to use the data buffer accessors
  [SCSI] ncr53c8xx: convert to use the data buffer accessors
  [SCSI] sym53c8xx: convert to use the data buffer accessors
  [SCSI] ppa: coding police and printk levels
  [SCSI] aic7xxx_old: remove redundant GFP_ATOMIC from kmalloc
  [SCSI] i2o: remove redundant GFP_ATOMIC from kmalloc from device.c
  [SCSI] remove the dead CYBERSTORMIII_SCSI option
  [SCSI] don't build scsi_dma_{map,unmap} for !HAS_DMA
  [SCSI] Clean up scsi_add_lun a bit
  [SCSI] 53c700: Remove printk, which triggers because of low scsi clock on SNI RMs
  [SCSI] sni_53c710: Cleanup
  [SCSI] qla4xxx: Fix underrun/overrun conditions
  [SCSI] megaraid_mbox: use mutex instead of semaphore
  [SCSI] aacraid: add 51245, 51645 and 52245 adapters to documentation.
  [SCSI] qla2xxx: update version to 8.02.00-k1.
  [SCSI] qla2xxx: add support for NPIV
  [SCSI] stex: use resid for xfer len information
  [SCSI] Add Brownie 1200U3P to blacklist
  [SCSI] scsi.c: convert to use the data buffer accessors
  ...

* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (53 commits)
  [TCP]: Verify the presence of RETRANS bit when leaving FRTO
  [IPV6]: Call inet6addr_chain notifiers on link down
  [NET_SCHED]: Kill CONFIG_NET_CLS_POLICE
  [NET_SCHED]: act_api: qdisc internal reclassify support
  [NET_SCHED]: sch_dsmark: act_api support
  [NET_SCHED]: sch_atm: act_api support
  [NET_SCHED]: sch_atm: Lindent
  [IPV6]: MSG_ERRQUEUE messages do not pass to connected raw sockets
  [IPV4]: Cleanup call to __neigh_lookup()
  [NET_SCHED]: Revert "avoid transmit softirq on watchdog wakeup" optimization
  [NETFILTER]: nf_conntrack: UDPLITE support
  [NETFILTER]: nf_conntrack: mark protocols __read_mostly
  [NETFILTER]: x_tables: add connlimit match
  [NETFILTER]: Lower *tables printk severity
  [NETFILTER]: nf_conntrack: Don't track locally generated special ICMP error
  [NETFILTER]: nf_conntrack: Introduces nf_ct_get_tuplepr and uses it
  [NETFILTER]: nf_conntrack: make l3proto->prepare() generic and renames it
  [NETFILTER]: nf_conntrack: Increment error count on parsing IPv4 header
  [NET]: Add ethtool support for NETIF_F_IPV6_CSUM devices.
  [AF_IUCV]: Add lock when updating accept_q
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
  9p: fix a race condition bug in umount which caused a segfault
  9p: re-enable mount time debug option
  9p: cache meta-data when cache=loose
  net/9p: set error to EREMOTEIO if trans->write returns zero
  net/9p: change net/9p module name to 9pnet
  9p: Reorganization of 9p file system code

* 'for-linus' of git://oss.sgi.com:8090/xfs/xfs-2.6: (37 commits)
  [XFS] Fix lockdep annotations for xfs_lock_inodes
  [LIB]: export radix_tree_preload()
  [XFS] Fix XFS_IOC_FSBULKSTAT{,_SINGLE} & XFS_IOC_FSINUMBERS in compat mode
  [XFS] Compat ioctl handler for handle operations
  [XFS] Compat ioctl handler for XFS_IOC_FSGEOMETRY_V1.
  [XFS] Clean up function name handling in tracing code
  [XFS] Quota inode has no parent.
  [XFS] Concurrent Multi-File Data Streams
  [XFS] Use uninitialized_var macro to stop warning about rtx
  [XFS] XFS should not be looking at filp reference counts
  [XFS] Use is_power_of_2 instead of open coding checks
  [XFS] Reduce shouting by removing unnecessary macros from dir2 code.
  [XFS] Simplify XFS min/max macros.
  [XFS] Kill off xfs_count_bits
  [XFS] Cancel transactions on xfs_itruncate_start error.
  [XFS] Use do_div() on 64 bit types.
  [XFS] Fix remount,readonly path to flush everything correctly.
  [XFS] Cleanup inode extent size hint extraction
  [XFS] Prevent ENOSPC from aborting transactions that need to succeed
  [XFS] Prevent deadlock when flushing inodes on unmount
  ...

It depends on tristate I2C and it's trivial to make modular.  The
current Kconfig allows I2C=m, I2C_ACORN=y, which doesn't work at
all; alternatives are dependency on I2C=y and making I2C_ACORN
itself a tristate.  The latter is the right thing to do...
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fallout from commit 91a69029 ('sysfs:
add parameter "struct bin_attribute *" ...')
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Acked-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Acked-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

s390 is the only 32bit with unsigned long for size_t (usual for those
is unsigned int).  Tell sparse...
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It returns __sum16, not unsigned int
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

... so all proud owners of s390-based PDAs will have to live without that one
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Going through the string and waiting for _pointer_ to become '\0'
is not what the authors meant...
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Acked-by: NBen Collins <ben.collins@ubuntu.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Shows how many people are testing coda - the bug had been there for 5 years
and results of stepping on it are not subtle.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

still looks racy (and definitely leaks)
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

drivers/w1/slaves/w1_ds2760.c:85: warning: initialization from incompatible pointer type

The ACPI guys changed the bin_attr APIs
(commit 91a69029)

Cc: Anton Vorontsov <cbou@mail.ru>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>

Per Jeff Garzik request.
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NAnton Vorontsov <cbou@mail.ru>