The documentation for spi_master.set_cs() says:

    assert or deassert chip select, true to assert

i.e. its "enable" parameter uses assertion-level logic.

This does not match the implementation of spi_set_cs(), which calls
spi_master.set_cs() with the wanted logic level of the chip select line,
which depends on the polarity of the chip select signal.

Correct the documentation to match the implementation.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NGeert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

spi_write_then_read() takes a "void *" for rxbuf, so there's no need to
cast the buffer pointer to "u8 *".
Signed-off-by: NGeert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

Trent Piepho observed that since the current realistic maximum number of
data lines is four we can pack the spi_transfer struct more efficiently
if we use a bitfield for the number of bits, allowing the fields to fit
in a single byte along with cs_change.

If space becomes an issue further optimiation is possible by only using
the constants and packing the values chosen for them.
Reported-by: NTrent Piepho <tpiepho@gmail.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Currently, the tx queue were selected implicitly in ndo_dfwd_start_xmit(). The
will cause several issues:

- NETIF_F_LLTX were removed for macvlan, so txq lock were done for macvlan
  instead of lower device which misses the necessary txq synchronization for
  lower device such as txq stopping or frozen required by dev watchdog or
  control path.
- dev_hard_start_xmit() was called with NULL txq which bypasses the net device
  watchdog.
- dev_hard_start_xmit() does not check txq everywhere which will lead a crash
  when tso is disabled for lower device.

Fix this by explicitly introducing a new param for .ndo_select_queue() for just
selecting queues in the case of l2 forwarding offload. netdev_pick_tx() was also
extended to accept this parameter and dev_queue_xmit_accel() was used to do l2
forwarding transmission.

With this fixes, NETIF_F_LLTX could be preserved for macvlan and there's no need
to check txq against NULL in dev_hard_start_xmit(). Also there's no need to keep
a dedicated ndo_dfwd_start_xmit() and we can just reuse the code of
dev_queue_xmit() to do the transmission.

In the future, it was also required for macvtap l2 forwarding support since it
provides a necessary synchronization method.

Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: e1000-devel@lists.sourceforge.net
Signed-off-by: NJason Wang <jasowang@redhat.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fiq.h contains only a function declaration and is not used by anyone
else. Move the declaration to the driver header file and remove the
unnecessary platform dependency from the driver.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

VM to VM GSO traffic is broken if it goes through VXLAN or GRE
tunnel and the physical NIC on the host supports hardware VXLAN/GRE
GSO offload (e.g. bnx2x and next-gen mlx4).

Two issues -
(VXLAN) VM traffic has SKB_GSO_DODGY and SKB_GSO_UDP_TUNNEL with
SKB_GSO_TCP/UDP set depending on the inner protocol. GSO header
integrity check fails in udp4_ufo_fragment if inner protocol is
TCP. Also gso_segs is calculated incorrectly using skb->len that
includes tunnel header. Fix: robust check should only be applied
to the inner packet.

(VXLAN & GRE) Once GSO header integrity check passes, NULL segs
is returned and the original skb is sent to hardware. However the
tunnel header is already pulled. Fix: tunnel header needs to be
restored so that hardware can perform GSO properly on the original
packet.
Signed-off-by: NWei-Chun Chao <weichunc@plumgrid.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SCTP outqueue structure maintains a data chunks
that are pending transmission, the list of chunks that
are pending a retransmission and a length of data in
flight.  It also tries to keep the emtpy state so that
it can performe shutdown sequence or notify user.

The problem is that the empy state is inconsistently
tracked.  It is possible to completely drain the queue
without sending anything when using PR-SCTP.  In this
case, the empty state will not be correctly state as
report by Jamal Hadi Salim <jhs@mojatatu.com>.  This
can cause an association to be perminantly stuck in the
SHUTDOWN_PENDING state.

Additionally, SCTP is incredibly inefficient when setting
the empty state.  Even though all the data is availaible
in the outqueue structure, we ignore it and walk a list
of trasnports.

In the end, we can completely remove the extra empty
state and figure out if the queue is empty by looking
at 3 things:  length of pending data, length of in-flight
data, and exisiting of retransmit data.  All of these
are already in the strucutre.
Reported-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NVlad Yasevich <vyasevich@gmail.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Tested-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Function llc_conn_ac_inc_vr_by_1() evaluates via macro
PDU_GET_NEXT_Vr() into ...

  llc_sk(sk)->vR = ++llc_sk(sk)->vR & 0xffffffffffffff7f

... but the order in which the side effects take place is
undefined because there is no intervening sequence point.

As llc_sk(sk)->vR is written in llc_sk(sk)->vR (assignment
left-hand side) and written in ++llc_sk(sk)->vR & 0xffffffffffffff7f
this might possibly yield undefined behavior.

The final value of llc_sk(sk)->vR is ambiguous, because,
depending on the order of expression evaluation, the
increment may occur before, after, or interleaved with
the assignment. In C, evaluating such an expression yields
undefined behavior.

Since we're doing the increment via PDU_GET_NEXT_Vr() macro
and the only place it is being used is from
llc_conn_ac_inc_vr_by_1(), in order to increment vR by 1
with a follow-up optimized modulo, rewrite the expression
into ((vR + 1) & CONST) in order to fix this.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the vlan code detects that the real device can do TX VLAN offloads
in hardware, it tries to arrange for the real device's header_ops to
be invoked directly.

But it does so illegally, by simply hooking the real device's
header_ops up to the VLAN device.

This doesn't work because we will end up invoking a set of header_ops
routines which expect a device type which matches the real device, but
will see a VLAN device instead.

Fix this by providing a pass-thru set of header_ops which will arrange
to pass the proper real device instead.

To facilitate this add a dev_rebuild_header().  There are
implementations which provide a ->cache and ->create but not a
->rebuild (f.e. PLIP).  So we need a helper function just like
dev_hard_header() to avoid crashes.

Use this helper in the one existing place where the
header_ops->rebuild was being invoked, the neighbour code.

With lots of help from Florian Westphal.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The changes in the ACPI-based PCI hotplug (ACPIPHP) subsystem made
during the 3.12 development cycle uncovered a problem with VGA
switcheroo that on some systems, when the device-specific method
(ATPX in the radeon case, _DSM in the nouveau case) is used to turn
off the discrete graphics, the BIOS generates ACPI hotplug events for
that device and those events cause ACPIPHP to attempt to remove the
device from the system (they are events for a device that was present
previously and is not present any more, so that's what should be done
according to the spec).  Then, the system stops functioning correctly.

Since the hotplug events in question were simply silently ignored
previously, the least intrusive way to address that problem is to
make ACPIPHP ignore them again.  For this purpose, introduce a new
ACPI device flag, no_hotplug, and modify ACPIPHP to ignore hotplug
events for PCI devices whose ACPI companions have that flag set.
Next, make the radeon and nouveau switcheroo detection code set the
no_hotplug flag for the discrete graphics' ACPI companion.

Fixes: bbd34fcd (ACPI / hotplug / PCI: Register all devices under the given bridge)
References: https://bugzilla.kernel.org/show_bug.cgi?id=61891
References: https://bugzilla.kernel.org/show_bug.cgi?id=64891Reported-and-tested-by: NMike Lothian <mike@fireburn.co.uk>
Reported-and-tested-by: <madcatx@atlas.cz>
Reported-and-tested-by: NJoaquín Aramendía <samsagax@gmail.com>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+

Commit 54ecf4f0 ("ARM: w90x900: move platform_data definitions")
moved the file to the current location but forgot to remove the pointer
to its previous location. Clean it up. While at it also change the header
file protection macros appropriately.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

We've seen so many instances of people invoking skb_tx_timestamp()
after the device already has been given the packet, that it's worth
being a little bit more verbose and explicit in this comment.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 2171364d ("powerpc: Add HWCAP2 aux entry") introduced a new
AT_ auxv entry type AT_HWCAP2 but failed to update AT_VECTOR_SIZE_BASE
accordingly.
Signed-off-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Fixes: 2171364d (powerpc: Add HWCAP2 aux entry)
Cc: stable@vger.kernel.org
Acked-by: NMichael Neuling <michael@neuling.org>
Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This will allow userspace to correctly program the PA_SC_RASTER_CONFIG
register, so it can be considered a fix.
Signed-off-by: NMarek Olšák <marek.olsak@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Fixes rendering corruption due to incorrect
gfx configuration.

bug:
https://bugs.freedesktop.org/show_bug.cgi?id=63599Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

The arbitrary restriction on page counts offered by the core
migrate_page_move_mapping() code results in rather suspicious looking
fiddling with page reference counts in the aio_migratepage() operation.
To fix this, make migrate_page_move_mapping() take an extra_count parameter
that allows aio to tell the code about its own reference count on the page
being migrated.

While cleaning up aio_migratepage(), make it validate that the old page
being passed in is actually what aio_migratepage() expects to prevent
misbehaviour in the case of races.
Signed-off-by: NBenjamin LaHaise <bcrl@kvack.org>

Some pstore backing devices use on board flash as persistent
storage. These have limited numbers of write cycles so it
is a poor idea to use them from high frequency operations.
Signed-off-by: NTony Luck <tony.luck@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In struct page we have enough space to fit long-size page->ptl there,
but we use dynamically-allocated page->ptl if size(spinlock_t) is larger
than sizeof(int).

It hurts 64-bit architectures with CONFIG_GENERIC_LOCKBREAK, where
sizeof(spinlock_t) == 8, but it easily fits into struct page.
Signed-off-by: NKirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: NHugh Dickins <hughd@google.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Sasha Levin found a NULL pointer dereference that is due to a missing
page table lock, which in turn is due to the pmd entry in question being
a transparent huge-table entry.

The code - introduced in commit 1998cc04 ("mm: make
madvise(MADV_WILLNEED) support swap file prefetch") - correctly checks
for this situation using pmd_none_or_trans_huge_or_clear_bad(), but it
turns out that that function doesn't work correctly.

pmd_none_or_trans_huge_or_clear_bad() expected that pmd_bad() would
trigger if the transparent hugepage bit was set, but it doesn't do that
if pmd_numa() is also set. Note that the NUMA bit only gets set on real
NUMA machines, so people trying to reproduce this on most normal
development systems would never actually trigger this.

Fix it by removing the very subtle (and subtly incorrect) expectation,
and instead just checking pmd_trans_huge() explicitly.
Reported-by: NSasha Levin <sasha.levin@oracle.com>
Acked-by: NAndrea Arcangeli <aarcange@redhat.com>
[ Additionally remove the now stale test for pmd_trans_huge() inside the
  pmd_bad() case - Linus ]
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch allows FILEIO to update hw_max_sectors based on the current
max_bytes_per_io.  This is required because vfs_[writev,readv]() can accept
a maximum of 2048 iovecs per call, so the enforced hw_max_sectors really
needs to be calculated based on block_size.

This addresses a >= v3.5 bug where block_size=512 was rejecting > 1M
sized I/O requests, because FD_MAX_SECTORS was hardcoded to 2048 for
the block_size=4096 case.

(v2: Use max_bytes_per_io instead of ->update_hw_max_sectors)
Reported-by: NHenrik Goldman <hg@x-formation.com>
Cc: <stable@vger.kernel.org> #3.5+
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

According to documentation on barriers, stores issued before a LOCK can
complete after the lock implying that it's possible tlb_flush_pending
can be visible after a page table update.  As per revised documentation,
this patch adds a smp_mb__before_spinlock to guarantee the correct
ordering.
Signed-off-by: NMel Gorman <mgorman@suse.de>
Acked-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: NRik van Riel <riel@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There are a few subtle races, between change_protection_range (used by
mprotect and change_prot_numa) on one side, and NUMA page migration and
compaction on the other side.

The basic race is that there is a time window between when the PTE gets
made non-present (PROT_NONE or NUMA), and the TLB is flushed.

During that time, a CPU may continue writing to the page.

This is fine most of the time, however compaction or the NUMA migration
code may come in, and migrate the page away.

When that happens, the CPU may continue writing, through the cached
translation, to what is no longer the current memory location of the
process.

This only affects x86, which has a somewhat optimistic pte_accessible.
All other architectures appear to be safe, and will either always flush,
or flush whenever there is a valid mapping, even with no permissions
(SPARC).

The basic race looks like this:

CPU A			CPU B			CPU C

						load TLB entry
make entry PTE/PMD_NUMA
			fault on entry
						read/write old page
			start migrating page
			change PTE/PMD to new page
						read/write old page [*]
flush TLB
						reload TLB from new entry
						read/write new page
						lose data

[*] the old page may belong to a new user at this point!

The obvious fix is to flush remote TLB entries, by making sure that
pte_accessible aware of the fact that PROT_NONE and PROT_NUMA memory may
still be accessible if there is a TLB flush pending for the mm.

This should fix both NUMA migration and compaction.

[mgorman@suse.de: fix build]
Signed-off-by: NRik van Riel <riel@redhat.com>
Signed-off-by: NMel Gorman <mgorman@suse.de>
Cc: Alex Thorlton <athorlton@sgi.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

do_huge_pmd_numa_page() handles the case where there is parallel THP
migration.  However, by the time it is checked the NUMA hinting
information has already been disrupted.  This patch adds an earlier
check with some helpers.
Signed-off-by: NMel Gorman <mgorman@suse.de>
Reviewed-by: NRik van Riel <riel@redhat.com>
Cc: Alex Thorlton <athorlton@sgi.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 1b3a5d02 ("reboot: move arch/x86 reboot= handling to generic
kernel") moved reboot= handling to generic code.  In the process it also
removed the code in native_machine_shutdown() which are moving reboot
process to reboot_cpu/cpu0.

I guess that thought must have been that all reboot paths are calling
migrate_to_reboot_cpu(), so we don't need this special handling.  But
kexec reboot path (kernel_kexec()) is not calling
migrate_to_reboot_cpu() so above change broke kexec.  Now reboot can
happen on non-boot cpu and when INIT is sent in second kerneo to bring
up BP, it brings down the machine.

So start calling migrate_to_reboot_cpu() in kexec reboot path to avoid
this problem.

Bisected by WANG Chao.
Reported-by: NMatthew Whitehead <mwhitehe@redhat.com>
Reported-by: NDave Young <dyoung@redhat.com>
Signed-off-by: NVivek Goyal <vgoyal@redhat.com>
Tested-by: NBaoquan He <bhe@redhat.com>
Tested-by: NWANG Chao <chaowang@redhat.com>
Acked-by: NH. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ipgre_header_parse() needs to parse the tunnel's ip header and it
uses mac_header to locate the iphdr. This got broken when gre tunneling
was refactored as mac_header is no longer updated to point to iphdr.
Introduce skb_pop_mac_header() helper to do the mac_header assignment
and use it in ipgre_rcv() to fix msg_name parsing.

Bug introduced in commit c5441932 (GRE: Refactor GRE tunneling code.)

Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: NTimo Teräs <timo.teras@iki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is useful to be able to walk all upper devices when bringing
a device online where the RTNL lock is held. In this case it
is safe to walk the all_adj_list because the RTNL lock is used
to protect the write side as well.

This patch adds a check to see if the rtnl lock is held before
throwing a warning in netdev_all_upper_get_next_dev_rcu().

Also because we now have a call site for lockdep_rtnl_is_held()
outside COFIG_LOCK_PROVING an inline definition returning 1 is
needed. Similar to the rcu_read_lock_is_held().

Fixes: 2a47fa45 ("ixgbe: enable l2 forwarding acceleration for macvlans")
CC: Veaceslav Falico <vfalico@redhat.com>
Reported-by: NYuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Commit fdfbbd07 ("perf: Add generic transaction flags")
added support for PERF_SAMPLE_TRANSACTION but forgot to add documentation
for the sample type to include/uapi/linux/perf_event.h
Signed-off-by: NVince Weaver <vincent.weaver@maine.edu>
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Cc: Andi Kleen <ak@linux.intel.com>
Link: http://lkml.kernel.org/r/alpine.DEB.2.02.1312131548450.10372@pianoman.cluster.toySigned-off-by: NIngo Molnar <mingo@kernel.org>

Certain drives cannot handle queued TRIM commands properly, even
though support is indicated in the IDENTIFY DEVICE buffer.  This patch
allows for disabling the commands for the affected drives and apply it
to the Micron/Crucial M500 SSDs which exhibit incorrect protocol
behavior when issued queued TRIM commands, which could lead to silent
data corruption.

tj: Merged two unnecessarily split patches and made minor edits
    including shortening horkage name.
Signed-off-by: NMarc Carino <marc.ceeeee@gmail.com>
Signed-off-by: NTejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/g/1387246554-7311-1-git-send-email-marc.ceeeee@gmail.com
Cc: stable@vger.kernel.org # 3.12+

Now that spi_device->mode is a u16, the chip_select, bits_per_mode,
and mode fields pack poorly, taking 8 bytes:  four data and four
padding.  By moving (u8)bits_per_word up one position, to after
(u8)chip_select, they pack better and only use 4 bytes.
Signed-off-by: NTrent Piepho <tpiepho@gmail.com>
Reviewed-by: NSourav Poddar <sourav.poddar@ti.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>g
Signed-off-by: NMark Brown <broonie@linaro.org>

Userspace input buffer is not modified by kernel, so it can be 'const'.

This is also a prerequisite to remove the implicit cast
from INIT_UDATA().

Link: http://marc.info/?i=cover.1386798254.git.ydroneaud@opteya.com>
Signed-off-by: NYann Droneaud <ydroneaud@opteya.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Some devices with support for mobile networks may have buttons for
enabling/disabling such connection. An example can be Linksys router 54G3G.
We already have KEY_BLUETOOTH, KEY_WLAN and KEY_UWB so it makes sense to
add KEY_WWAN as well.  As we already have KEY_WIMAX, use it's value for
KEY_WWAN and make it an alias.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

On ARM (32 bits and 64 bits), the double-word is 8-bytes aligned. This will
result on different structure from Xen and Linux repositories.

As Linux is using __packed__ attribute, it must have a 4-bytes padding before
each "id" field.

This change breaks guest block support with older kernel. IMHO, it's acceptable
because Xen on ARM is still on Tech Preview and the hypercall ABI is not yet
freezed.

Only one architecture (x86_32) doesn't have 64-bit ABI for the block interface.
Don't add padding if Linux is compiled for this architecture.
Signed-off-by: NJulien Grall <julien.grall@linaro.org>
Acked-by: NRoger Pau Monne <roger.pau@citrix.com>
Acked-by: NDavid Vrabel <david.vrabel@citrix.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Acked-by: NStefano Stabellini <stefano.stabellini@eu.citrix.com>
[I had asked for confirmation that it did not break x86 and Ian went
beyound the call of duty to confirm it. Also a internal regression
bucket with 32/64 dom0 with 32/64 domU (PV and HVM) confirmed no
regressions. ABI changes are a drag..]
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Rename old regmap field of "struct sec_pmic_dev" to "regmap_pmic" and
add new regmap for RTC.

On S5M8767A registers were not properly updated and read due to usage of
the same regmap as the PMIC.  This could be observed in various hangs,
e.g.  in infinite loop during waiting for UDR field change.

On this chip family the RTC has different I2C address than PMIC so
additional regmap is needed.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: NMark Brown <broonie@linaro.org>
Acked-by: NSangbeom Kim <sbkim73@samsung.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The machine cannot fault if !MUU, so make might_fault() a nop for !MMU.

This fixes below build error if
!CONFIG_MMU && (CONFIG_PROVE_LOCKING=y || CONFIG_DEBUG_ATOMIC_SLEEP=y):

  arch/arm/kernel/built-in.o: In function `arch_ptrace':
  arch/arm/kernel/ptrace.c:852: undefined reference to `might_fault'
  arch/arm/kernel/built-in.o: In function `restore_sigframe':
  arch/arm/kernel/signal.c:173: undefined reference to `might_fault'
  ...
  arch/arm/kernel/built-in.o:arch/arm/kernel/signal.c:177: more undefined references to `might_fault' follow
  make: *** [vmlinux] Error 1
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

With CONFIG_HUGETLBFS=n:

  mm/migrate.c: In function `do_move_page_to_node_array':
  include/linux/hugetlb.h:140:33: warning: statement with no effect [-Wunused-value]
   #define isolate_huge_page(p, l) false
                                   ^
  mm/migrate.c:1170:4: note: in expansion of macro `isolate_huge_page'
      isolate_huge_page(page, &pagelist);
Reported-by: NBorislav Petkov <bp@alien8.de>
Tested-by: NBorislav Petkov <bp@alien8.de>
Signed-off-by: NNaoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: NDavid Rientjes <rientjes@google.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

neigh_priv_len is defined as u8. With all debug enabled struct
ipoib_neigh has 200 bytes. The largest part is sk_buff_head with 96
bytes and here the spinlock with 72 bytes.
The size value still fits in this u8 leaving some room for more.

On -RT struct ipoib_neigh put on weight and has 392 bytes. The main
reason is sk_buff_head with 288 and the fatty here is spinlock with 192
bytes. This does no longer fit into into neigh_priv_len and gcc
complains.

This patch changes neigh_priv_len from being 8bit to 16bit. Since the
following element (dev_id) is 16bit followed by a spinlock which is
aligned, the struct remains with a total size of 3200 (allmodconfig) /
2048 (with as much debug off as possible) bytes on x86-64.
On x86-32 the struct is 1856 (allmodconfig) / 1216 (with as much debug
off as possible) bytes long. The numbers were gained with and without
the patch to prove that this change does not increase the size of the
struct.

Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Whilst architectures may be able to do better than this (which they can,
by simply defining their own macro), this is a generic stab at a
zero_bytemask implementation for the asm-generic, big-endian
word-at-a-time implementation.

On arm64, a clz instruction is used to implement the fls efficiently.
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When explicitly hashing the end of a string with the word-at-a-time
interface, we have to be careful which end of the word we pick up.

On big-endian CPUs, the upper-bits will contain the data we're after, so
ensure we generate our masks accordingly (and avoid hashing whatever
random junk may have been sitting after the string).

This patch adds a new dcache helper, bytemask_from_count, which creates
a mask appropriate for the CPU endianness.

Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 04f3b31b ("iscsi-target: Convert iscsi_session statistics to
atomic_long_t") removed the updating of these fields in iscsi (the only
fabric driver that ever touched these counters), and the core has no way
to report or otherwise use the values.  Remove the last remnants of
these counters.
Signed-off-by: NRoland Dreier <roland@purestorage.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>