mtdchar return -EINVAL for seek prior to offset 0 or to beyond the last
byte in the device/partition, similar to various other seek methods,
instead of fixing up to first or last byte.
Signed-off-by: NTodd Poynor <tpoynor@mvista.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Remove useless udelay(100) after status value already read.  Poll
for status OK with reduced udelay if not immediate OK status return.

Fix read and compare of 32-bit status value using 16-bit variable.

Include slab.h since kmalloc/kfree are called.
Signed-off-by: NTodd Poynor <tpoynor@mvista.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

mtdblock (and other mtd modules that use the mtd_blkdevs interface
between the mtd translation layers and the linux block layer) handles
incorrectly more than 10 devices or 26 partitions in the names passed to
the generic disk layer.  This causes the device file names and other
info kept by the generic disk/block layers to have names such as
"mtdblock<".  Use integer formatting for device numbers; use "aa-az"
for partitions 27-52, "ba-bz" for 53-78...
Signed-off-by: NTodd Poynor <tpoynor@mvista.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Remove mtd_blkdevs refs to the no longer functional DEVFS filesystem.

Verified mtdblock continues to work fine via udev with these calls
removed.
Signed-off-by: NTodd Poynor <tpoynor@mvista.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Modify Amd/Fujitsu CFI NOR flash primary vendor extension table revision
check to recognize version 1.4.  Verified the existing driver can
handle version 1.4 chips without additional info from 1.4 extended table.

Move the primary vendor extension table revision check from common file
to the 3 CFI chip driver files, since the data structures and revisions
handled by those data structures are specific to the chip driver.

Modify the error message printed when the revision is unknown to be a
KERN_ERR instead of WARNING since this will cause mtd to ignore the chip.
Signed-off-by: NTodd Poynor <tpoynor@mvista.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

For 2.6.12 behaviour, this (EXPERIMENTAL) driver
should not be built.

Update the driver source with latest from Luming.
Signed-off-by: NLuming Yu <luming.yu@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by Len Brown <len.brown@intel.com>

Burst mode isn't ready for prime time,
but can be enabled for test via "ec_burst=1"
Signed-off-by: NLuming Yu <luming.yu@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Patch from Ian Campbell

On PXA255 there is no way to disable the watchdog. Turning off OIER[E3]
as suggested in the existing comment does not work.

I posted a note to the ARM mailing list a little while ago asking for
opinions from people using SA1100. There was one reponse from Nico who
believes that the SA1100 is the same as the PXA255 in this respect.

You also asked me to involve the watchdog maintainer which I tried to
do but didn't hear anything back. There are only a couple of other
drivers which can't stop the watchdog and there seems to be no
consistancy regarding printing an error etc. I decided to print
something since that matches the case for all the other drivers when
NOWAYOUT is turned on.

Also, I changed the device .name to "watchdog" like most of the other
watchdogs. udev uses it as the device name (by default) and spaces etc.
get in the way.

Superceded 2833/1 because 2.6.13-rc4 caused rejects.
Signed-off-by: NIan Campbell <icampbell@arcom.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Deepak Saxena

This allows the serial driver autconf to work properly on all the IXP
serial ports. W/o it we basically put the serial port in an unrecoverable
state and lose console.
Signed-off-by: NDeepak Saxena <dsaxena@plexity.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Catalin Marinas

The IEEE 754 standard specifies that the result of (x - x), where x is
a valid number, should be -0 if the rounding mode is towards minus
infinity or +0 otherwise.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Michael Burian

This file is maintained by RMK's machine registry, it should not be patched.
Signed-off-by: NMichael Burian <dynmail1@gassner-waagen.at>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Deepak Saxena

The XScale locking code is not something that has been validated
on 2.6 and needs to be replaced with a more generic API to use
with other ARMs that support locking features.
Signed-off-by: NDeepak Saxena <dsaxena@plexity.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Richard Purdie

NWFPE used global variables which meant it wasn't safe for use with
preemptive kernels. This patch removes them and communicates the
information between functions in a preempt safe manner. Generation
of some exceptions was broken and this has also been corrected.
Tests with glibc's maths test suite show no change in the results
before/after this patch.
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

The default clock rate does not specify a maximum, so the
default of 400KHz is used. This rate is too fast for the PMU
on the EB2410ITX, so we now specify platform data with a rate
of around 100KHz.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The VM_FAULT_WRITE thing is an extra bit, not a valid return value, and
has to be treated as such by get_user_pages().
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Checking pte_dirty instead of pte_write in __follow_page is problematic
for s390, and for copy_one_pte which leaves dirty when clearing write.

So revert __follow_page to check pte_write as before, and make
do_wp_page pass back a special extra VM_FAULT_WRITE bit to say it has
done its full job: once get_user_pages receives this value, it no longer
requires pte_write in __follow_page.

But most callers of handle_mm_fault, in the various architectures, have
switch statements which do not expect this new case.  To avoid changing
them all in a hurry, make an inline wrapper function (using the old
name) that masks off the new bit, and use the extended interface with
double underscores.

Yes, we do have a call to do_wp_page from do_swap_page, but no need to
change that: in rare case it's needed, another do_wp_page will follow.
Signed-off-by: NHugh Dickins <hugh@veritas.com>
[ Cleanups by Nick Piggin ]
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch disables the PCI Interrupt Link refernece counts,
which should not co-exist with the 2.6.12 irq_router.resume
method or else a double acpi_pci_link_set() could result
on resume.
Signed-off-by: NDavid Shaohua Li <shaohua.li@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

For soft reset during system hang, got an error "CPU did not take
control" for some CPUs even though they responded to soft-reset (called
SystemReset, die and called debugger - xmon).   First these CPUs entered
into xmon by IPI callback and then got a soft-reset exception and
re-entered into xmon again. The first CPU which re-entered into xmon got
the output lock and made into xmon successfully without unlocking.
Hence, the next CPU(s) which re-entered into xmon try to acquire a lock
(get_output_lock). Therefore, we can not view state of those CPU(s).

[This is a simple, very low risk, obvious fix for an obvious bug, and
should go into 2.6.13.  -- paulus]
Signed-off-by: NHaren Myneni <hbabu@us.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NLen Brown <len.brown@intel.com>

We have increased PCIBIOS_MIN_IO to 0x4000, but still want
motherboard resources to be allocated properly. So we need
to state 0x1000 (according to the comment) limit explicitely.
Signed-off-by: NIvan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

There is a number of x86 laptops that have some non-PCI IO ports
in the 0x1000-0x1fff range, and it's quite hard to control the correct
order of resource allocation between PCI and other subsystems controlling
these ports. Especially with modular kernel.

So just increase PCIBIOS_MIN_IO to 0x4000 to prevent any new PCI
resource allocations in the problematic range (this limitation must
apply _only_ to the root bus resources - see Linus' change in
pci_bus_alloc_resource).  As PCIBIOS_MIN_IO and PCIBIOS_MIN_CARDBUS_IO
are the same now on i386 and x86-64, we can remove the latter.
Signed-off-by: NIvan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The reason we have PCIBIOS_MIN_IO and PCIBIOS_MIN_CARDBUS_IO is because
we want to protect badly documented motherboard PCI resources and thus
don't want to allocate new resources in low IO/MEM space.

However, if we have already discovered a PCI bridge with a specified
resource base, that should override that decision.

This change will allow us to move the "careful" region upwards without
resulting in problems allocating resources in low mappings.  This was
brought on by us having allocated a bus resource at 0x1000, conflicting
with a undocumented VAIO Sony PI resources.

CFQ will currently stall when using write barriers and the default
max_depth setting of 1, since we artificially need a depth of 2 when
pre-pending the first flush. So never deny the barrier request going to
the device.

This is a regression since 2.6.12, it was found in SUSE testing.
Signed-off-by: NJens Axboe <axboe@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Rebuild the aic7xxx firmware doesn't work anymore after this change
which appeared int 2.6.13-rc1:

   [SCSI] aic7xxx/aic79xx: remove useless byte order macro cruft

Two files did not include byteorder.h, resulting in aic dying with a panic

	"Unknown opcode encountered in seq program"

This fixes it for me.
Signed-off-by: NOlaf Hering <olh@suse.de>
Acked-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Recent changes (well, dating from 12 July) have broken cardbus on my
powerbook: I get 3 messages saying "no resource of type xxx available,
trying to continue", and if I plug in my wireless card, it complains
that there are no resources allocated to the card.  This all worked in
2.6.12.

Looking at the code in yenta_socket.c, function yenta_allocate_res,
it's obvious what is wrong: if we get to line 639 (i.e. there wasn't a
usable preassigned resource), we will always flow through to line 668,
which is the printk that I was seeing, even if a resource was
successfully allocated.  It looks to me as though there should be a
return statement after the two config_writel's in each of the 3
branches of the if statements, so that the function returns after
successfully setting up the resource.

The patch below adds these return statements, and with this patch,
cardbus works on my powerbook once again.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Acked-by: NDominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Ok, let's get it right this time

If CONFIG_NUMA is set, some POWER 4 systems will fail to boot.  This is
because of special processing needed to handle invalid node IDs (0xffff) on
POWER 4.  My previous patch to handle memory 'holes' within nodes forgot to
add this special case for POWER 4 in one place.

In reality, I'm not sure that configuring the kernel for NUMA on POWER 4 makes
much sense.  Are there POWER 4 based systems with NUMA characteristics that
are presented by the firmware?  But, distros want one kernel for all systems
so NUMA is on by default in their kernels.  The patch handles those cases.
Signed-off-by: NMike Kravetz <kravetz@us.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The module code assumes noone will ever ask for a per-cpu area more than
SMP_CACHE_BYTES aligned.  However, as these cases show, gcc asks sometimes
asks for 32-byte alignment for the per-cpu section on a module, and if
CONFIG_X86_L1_CACHE_SHIFT is 4, we hit that BUG_ON().  This is obviously an
unusual combination, as there have been few reports, but better to warn
than die.

See:
	http://www.ussg.iu.edu/hypermail/linux/kernel/0409.0/0768.html

And more recently:
	http://bugs.gentoo.org/show_bug.cgi?id=97006Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Dont include asm-generic/topology.h unconditionally, we end up overriding
all the ppc64 specific functions when NUMA is on.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Acked-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix bug found by Grant Coady <lkml@dodo.com.au>'s autobuild setup.

shmem_set_policy() and shmem_get_policy() are macros if !CONFIG_SHMEM, so this
doesn't work.
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix bug found by Grant Coady <lkml@dodo.com.au>'s autobuild setup.
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

A kernel BUG() is triggered by a call to set_mempolicy() with a negative
first argument.  This is because the mode is declared as an int, and the
validity check doesnt check < 0 values.  Alternatively, mode could be
declared as unsigned int or unsigned long.
Signed-off-by: NEric Dumazet <dada1@cosmosbay.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

x86_64 has a large sparse gate area between VSYSCALL_START and
VSYSCALL_END, not all of it presently backed by pmds.  Alexander Nyberg has
found that in some circumstances gdb may try to ptrace here, and hit
get_user_pages BUG_ON.  It seems odd that gdb should be accessing here, but
it certainly shouldn't crash in this way: relax BUG_ON to -EFAULT.  Fixes
kernel bugzilla #4801.
Signed-off-by: NHugh Dickins <hugh@veritas.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

If there was a read error, the bnode might miss some pages, so skip them.
Signed-off-by: NRoman Zippel <zippel@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

If inode size hasn't changed, don't do anything further in truncate, which
also prevents a dirty inode, what might upset some readonly devices quite
badly.
Signed-off-by: NRoman Zippel <zippel@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

We don't want these to be global functions.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>