Using strlcpy instead of memcpy makes the strlen() calls superfluous
and also ensures zero-termination of the copied string.
At the same time get rid of the magic constant 50.

Actually, I can't see why copying the callback name is necessary
instead of simply storing a pointer to it (just like to the callback
function itself), but that goes beyond the scope of this fix.
Signed-off-by: NFerenc Wagner <wferi@niif.hu>
Acked-by: N"Nandigama, Nagalakshmi" <Nagalakshmi.Nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

[Resend patch as per Bernd Schubert comment ]

Issue:

Device goes offline while doing aggressive HBA reset
along with IO using some utility.

Root cause:

FW goes into bad state due to aggressive reset. Softreset does not
help to recover FW. And also aggressive reset open up the window for
Error handling thread to kicked off at the same time HBA will be in
constant RESET loop as part of aggressive reset test case can lead
Device to goes offline.

Changes:

1. Added extra check as below inside eh_timed_out call back as below.
   if(ioc->ioc_reset_in_progress) Rc = EH_TIMER_RESET

2. Removed " DOORBELL_ACTIVE" check for SAS controller from task
   management context.  Since SAS controller uses high priority queue
   for task management. This check is not required for SAS controller.

3. Moved SoftReset call to HardReset from Task Mgmt context.
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Find Non-Operation IOC and remove it from OS: Detecting
dead(non-functional) ioc will be done reading doorbell register value
from fault reset thread, which has been called from work thread
context after each specific interval. If doorbell value is 0xFFFFFFFF,
it will be considered as IOC is non-operational and marked as dead
ioc.

Once Dead IOC has been detected, it will be removed at pci layer using
"pci_remove_bus_device" API.
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Using C line continuation inside format strings is error prone.
Clean up the unintended whitespace introduced by misuse of \.
Neaten correctly used line continations as well for consistency.

drivers/scsi/arcmsr/arcmsr_hba.c has these errors as well,
but arcmsr needs a lot more work and the driver should likely be
moved to staging instead.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>

SAS1.0 Controller was not able to detect SAS2.0 Expanders due to Link
RATE detection was limited to 1.5 Gbps and 3.0 Gbps for SAS1
controllers. Added detection for 6.0 Gbps link.  Now, user can mix-up
6.0 Gpbs links with SAS1.0 controller.

e.g SAS1.0 HBA <----> SAS2.0 Expander <------> SAS2.0 Expander <--------> SAS1.0 Drive.
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

"gadget", "through", "command", "maintain", "maintain", "controller", "address",
"between", "initiali[zs]e", "instead", "function", "select", "already",
"equal", "access", "management", "hierarchy", "registration", "interest",
"relative", "memory", "offset", "already",
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

In this code, 0 is returned on memory allocation failure, even though other
failures return -ENOMEM or other similar values.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression ret;
expression x,e1,e2,e3;
@@

ret = 0
... when != ret = e1
*x = \(kmalloc\|kcalloc\|kzalloc\)(...)
... when != ret = e2
if (x == NULL) { ... when != ret = e3
  return ret;
}
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Acked-by: N"Desai, Kashyap" <Kashyap.Desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Fix fusion missing kernel-doc:

  Warning(drivers/message/fusion/mptbase.c:649): No description found for parameter 'func_name'
  Warning(drivers/message/fusion/mptbase.c:8010): No description found for parameter 'cb_idx'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix comment begin notation not to look like kernel-doc
since it's not.  Removes kernel-doc warnings.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix (delete) empty kernel-doc lines/warnings:
Warning(drivers/message/fusion/mptbase.c:6916): bad line:
Warning(drivers/message/fusion/mptbase.c:7060): bad line:
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Convert everything except ->proc_info() stuff, it is done within separate
->proc_info path series.

Problem with ->read_proc et al is described here commit
786d7e16 "Fix rmmod/read/write races in
/proc entries"
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

No need to open code this!
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Reviewed-by: NTakashi Iwai <tiwai@suse.de>

Indent the branch of an if.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r disable braces4@
position p1,p2;
statement S1,S2;
@@

(
if (...) { ... }
|
if (...) S1@p1 S2@p2
)

@script:python@
p1 << r.p1;
p2 << r.p2;
@@

if (p1[0].column == p2[0].column):
  cocci.print_main("branch",p1)
  cocci.print_secs("after",p2)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Acked-by: N"Desai, Kashyap" <Kashyap.Desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

We should release the resources in error return code path.
The requested pci bars should be released under an error condition,
when mpt_mapresources fails.
Signed-off-by: NTomas Henzl <thenzl@redhat.com>
Acked-by: N"Desai, Kashyap" <Kashyap.Desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Adding function name in original debug prints and few more debug prints are
added.
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Printing Doorbell register in a case of hard reset and timeout
should be useful for figuring out the state of the system.
Signed-off-by: NKei Tokunaga <tokunaga.keiich@jp.fujitsu.com>
Acked-by: N"Desai, Kashyap" <Kashyap.Desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

In mpt_detach, call to pci_set_drvdata is redundant because it
has already been called in mpt_adapter_disable. In mpt_attach,
ioc->pcidev is set to pdev two times.
Signed-off-by: NBandan Das <bandan.das@stratus.com>
Acked-by: N"Desai, Kashyap" <Kashyap.Desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Added missing part which will reset ioc_reset_in_progress before returning from SoftResetHandler.
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

fw_events_off is flag checking for driver to do Event handling or not.
Normally it should be OFF at the time of initialization. Only enable it at
the time of INTR enable of device first time. This will always occur only
after resource allocation.

ioc->fw_events_off = 1 is set in mpt_attach()
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

mpt_config would only attempt a MUR before retrying the command. The
driver will now retry a second time with a hard reset before leaving
the function.
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Message Unit Reset - instructs the IOC to reset the Reply Post and
Free FIFO's. All the Message Frames on Reply Free FIFO are
discarded. All posted buffers are freed, and event notification is
turned off.  IOC doesnt reply to any outstanding request. This will
transfer IOC to READY state.  Message unit ready is less expensive
operations than Hard Reset.  soft reset will not force Firmware to
reload again, it only do clean up of Message units.

mpt_Soft_Hard_ResetHandler will first try for Soft Reset,if
it fails then go for big hammer reset which is Hard Reset.
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Fixes the following warning:
drivers/message/fusion/mptbase.c:129: warning: 'mpt_proc_root_dir' defined but not used
also moves it from public data section since it is static.
Signed-off-by: NErik Ekman <erik@kryo.se>
Acked-by: N"Desai, Kashyap" <Kashyap.Desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Since commit 9d2e9d66
mptsas driver fails to allocate memory for the MPT chain buffers
for second LSI adapter on PPC440SPe Katmai platform:
...
ioc1: LSISAS1068E B3: Capabilities={Initiator}
mptbase: ioc1: ERROR - Unable to allocate Reply, Request, Chain Buffers!
mptbase: ioc1: ERROR - didn't initialize properly! (-3)
mptsas: probe of 0002:31:00.0 failed with error -3

This commit increased MPT_FC_CAN_QUEUE value but initChainBuffers()
doesn't differentiate between SAS and FC causing increased allocation
for SAS case, too. Later pci_alloc_consistent() fails to allocate
increased chain buffer pool size for SAS case.

Provide a fix by looking at the bus type and using appropriate
MPT_SAS_CAN_QUEUE value while calculation of the number of chain
buffers.
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Acked-by: NKashyap Desai <kashyap.desai@lsi.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Powerpc 44x uses 36 bit real address while the real address defined in
MPT Fusion driver is of type 32 bit. This causes ioremap to fail and
driver fails to initialize. This fix changes the data types
representing the real address from unsigned long 32-bit types to
resource_size_t which is 64-bit. The driver has been tested, the disks
get discovered correctly and can do IO.

[jejb: added printk fix for resource_size_t object]
Signed-off-by: NPravin Bathija <pbathija@amcc.com>
Acked-by: N"Desai, Kashyap" <Kashyap.Desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NUwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This patch is solving problem for PAE kernel DMA operation.
On PAE system dma_addr and unsigned long will have different
values.
Now dma_addr is not type casted using unsigned long.
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Code cleanup of host page alloc and diag reset.
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

We're about to make DMA_nnBIT_MASK() emit `deprecated' warnings.  Convert the
remaining stragglers which are visible to the x86_64 build.

Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Eric Moore <Eric.Moore@lsil.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Yi Zou <yi.zou@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix recent fusion driver kernel-doc fatal error and warnings.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Cc: Eric.Moore@lsi.com
Cc: support@lsi.com
Cc: DL-MPTFusionLinux@lsi.com
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

1. Handle integrated Raid device(Add/Delete) and error condition and check
   related to Raid device. is_logical_volume will represent logical volume
   device.
2. Raid device dual port support is added. Main functions to support this
   feature are mpt_raid_phys_disk_get_num_paths and mpt_raid_phys_disk_pg1.
Signed-off-by: NKashyap Desai <kadesai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NKashyap Desai <kadesai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Resending patch considering Grants G's code review.

Main goal to submit this patch is code cleaup.
1. Better driver debug prints and code indentation.
2. fault_reset_work_lock is not used anywhere. driver is using taskmgmt_lock
instead of fault_reset_work_lock.
3. setting pci_set_drvdata properly.
4. Ingore config request when IOC is in reset state.( ioc_reset_in_progress
is set).
5. Init/clear managment frame proprely.(INITIALIZE_MGMT_STATUS and
CLEAR_MGMT_STATUS)
Signed-off-by: NKashyap Desai <kadesai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Now Firmware events are handled by firmware event queue.
Previously it was handled in interrupt context/WorkQueue of Linux.
Firmware Event handling is restructured and optimized.
Signed-off-by: NKashyap Desai <kadesai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

1.) 	Added taskmgmt_quiesce_io flag in IOC and removed resetPending from
	_MPT_SCSI_HOST struct.
2.)	Reset from Scsi mid layer and internal Reset are seperate context.
	Adding DeviceResetCtx for internal Device reset frame.
	mptsas_taskmgmt_complete is optimized as part of implementation.
Signed-off-by: NKashyap Desai <kadesai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

1.)	 rewrite taskmanagement request and completion routines, making them
single threaded and using the generic MPT_MGMT struct, deleting
mptscsih_TMHandler, replacing with single request TM handler
mptscsih_IssueTaskMgmt, and killing the watchdog timer functions.
2.) cleanup ioc_reset callback handlers, introducing wrappers for
synchronizing error recovery (mpt_set_taskmgmt_in_progress_flag,
mpt_clear_taskmgmt_in_progress_flag), as the fusion firmware only handles
one task management request at a time
Signed-off-by: NKashyap Desai <kadesai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Rewrite of all internal generated functions that issue commands to firmware,
porting them to be single threaded using the generic MPT_MGMT
struct. Implemented using completion Queue.
Signed-off-by: NKashyap Desai <kadesai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

1) 	Previously we had mutliple #defines to use same values.
	Now those #defines are optimized.
	MPT_IOCTL_STATUS_* is removed and  MPT_MGMT_STATUS_* are new
	#defines.
2.)	config path is optimized.
	Instead of wait Queue and timer, using completion Q.
3.)	mpt_timer_expired is not used.

[jejb: elide patch to eliminate mpt_timer_expired]
Signed-off-by: NKashyap Desai <kadesai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

SendEventNotification was handled through FIFO, now it is using doorbell to
communicate with hardware. Added Sleep Flag as an extra argument to support
Can-Sleep feature.  Resending patch including compilation error fix reviewed
by Grant Grundler.
Signed-off-by: NKashyap Desai <kadesai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>