Removes some functions that are not used anywhere:
test_read() edid_read_block() dpp_write() dpp_read()
esdp_write() esdp_read() cec_write_clr_set()

This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: NRickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Removes some functions that are not used anywhere:
vblanking() hblanking()

This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: NRickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

In order to have subsytem agnostic media bus format definitions we've
moved media bus definitions to include/uapi/linux/media-bus-format.h and
prefixed values with MEDIA_BUS_FMT instead of V4L2_MBUS_FMT.

Replace all references to the old definitions in i2c drivers.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

In order to have v4l2-compliance tool pass the G/S_EDID some modifications
where needed in the driver.
In particular, the edid.reserved zone must be blanked.

Based on a patch from Jean-Michel Hautbois <jean-michel.hautbois@vodalys.com>,
but reworked it a bit. It should use 'data' (which depends on edid.present)
instead of edid.blocks as the check whether edid data is present.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The log_status function should show HDMI information, but the test checking for
an HDMI input was inverted. Fix this.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org      # for v3.12 and up
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Both adv7604 and adv7842 had the same typo in the code that sets
the vertical backporch for the second interlaced field: it was
assigned to vbackporch instead of il_vbackporch.

In addition, the timings struct wasn't zeroed in the adv7842 driver,
leaving several fields to undefined values causing the timing match
function to fail.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Update the recommended writes to those mentioned in the Rev 1.5 version of the
ADV7611 Register Settings Recommendations document released by Analog Devices.
The document does not mention why the recommended settings have been updated,
but presumably those are more fine tuned settings that can enhance performance
in some cases.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add an inv_llc_pol field to platform data to control the clock polarity.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NHans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The HPD GPIO is used as an output but its direction is never set. Fix
it.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add support for the hsync-active, vsync-active and pclk-sample
properties to the DT bindings and control BT.656 mode implicitly.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Parse the device tree node to populate platform data. Only the ADV7611
is currently support with DT.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

And set input routing when initializing the device.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add support for optional GPIO-controlled HPD pins in addition to the
ADV7604-specific hotplug notifier.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This helps locating duplicates and inserting new headers.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The *_and_or() functions take an 'and' bitmask to be ANDed with the
register value before ORing it with th 'or' bitmask. As the functions
are used to mask and set bits selectively, this requires the caller to
invert the 'and' bitmask and is thus error prone. Replace those
functions with a *_clr_set() variant that takes a mask of bits to be
cleared instead of a mask of bits to be kept.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This allows replacing duplicate code blocks by loops over the arrays.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This one line function is called in a single location. Inline it.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The video enum_dv_timings and dv_timings_cap operations are deprecated
and unused. Remove them.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The video enum_dv_timings and dv_timings_cap operations are deprecated.
Implement the pad-level version of those operations to prepare for the
removal of the video version.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Replace the dummy video format operations by pad format operations that
configure the output format.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NHans Verkuil <hans.verkuil@cisco.com>
Tested-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The ADV7604 has sink pads for its HDMI and analog inputs. Report them.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Control operations are handled by the control framework and the subdev
control handlers are never called directly. Remove them.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This patch adds support for the Analog Devices ADV7611 HDMI receiver.
The adv7611 is quite similar to the adv7604. It has only one instead of four
HDMI inputs and no analog frontend though. Also some register bits have been
shuffled around, but large parts of their register maps are compatible.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Reviewed-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

When extracting multiple bits from a single register read the register
once and extract the bits on the read value.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

16-bit registers are read through two 8-bit read operations. Factorize
that common pattern into 16-bit read accessors to simplify the code.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

We do not want to modify the info string arrays ever, so no need to
waste stack space for them. While we are at it also make them const.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Register the device with the v4l2 asynchronous probing framework to
support asynchronous instantiation systems such as DT.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The subdev EDID ioctls receive a pad field that must reference an
existing pad and an EDID field that must point to a buffer. Validate
both fields in the core code instead of duplicating validation in all
drivers.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This timing must be supported by all HDMI equipment, so that's a
reasonable default.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Signed-off-by: NMartin Bugge <marbugge@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Signed-off-by: NMats Randgaard <matrandg@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Some sources are initially detected as DVI, and change to HDMI later.
This must be detected to set the right RGB quantization range.
Signed-off-by: NMats Randgaard <matrandg@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

If the input signal is DVI-D and quantization range is RGB full range,
gain and offset must be adjusted to get the right range on the output.
Signed-off-by: NMats Randgaard <matrandg@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

If the restart_stdi_once trick fails to find a valid
format the flag was never reset.
Signed-off-by: NMartin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

- Mute audio before switching inputs to avoid noise/pops
- Mute audio if audio FIFO over-/underflows (AD Recommended setting)
- Reset FIFO if it over-/underflows (AD Recommended setting)
Signed-off-by: NMats Randgaard <matrandg@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

ADV7604_FMT_CHANGE events was debounced in adv7604_isr() to avoid
that a receiver with a unstable input signal would block the event
handling for other inputs. This solution was prone to errors.

A better protection agains interrupt blocking is to delay the call
of the interrupt service routine in the adv7604 driver if too many
interrupts are received within a given time.
Signed-off-by: NMats Randgaard <matrandg@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Signed-off-by: NMats Randgaard <matrandg@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

May also be wrong if the receiver is connected to more than one connector.
Signed-off-by: NMats Randgaard <matrandg@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

- split edid_write_block()
- do not use edid->edid before the validity check
- Return -EINVAL if edid->pad is invalid
- Save both registers for SPA port A
- Set SPA location to default value if it is not found
Signed-off-by: NMats Randgaard <matrandg@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>