OMAP3530 CBB package can have GPIO126 muxed on 2 pins: mmc1_dat4 and
cam_strobe. This causes a problem with current multipath GPIO mux
handling, which muxes both pins as GPIO126 and makes the GPIO unusable.

Fix this by not muxing any pins if multipath GPIO is detected and
just print a warning instead. It's up to board files to set correct
mux using omap_mux_init_signal and pin name.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds cpu hotplug support for OMAP4430. Only CPU inactive
state is supported as a low power state in the basic hot-plug support
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds a secure API to read AuxCoreBoot0 register to
check the cpu boot status. It also moves the other smc APIs
to common omap44xx-smc.S. This APIs should not be marked as
__INIT because we need these to be present for CPU hotplug
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds support for basic suspend doing a CPUx wfi
for OMAP4. All powerdomains are for now are kept programmed
in ON state.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Errata i202 (OMAP3430 - 1.12, OMAP3630 - 1.6):
UART module MDR1 register access can cause a dummy underrun
condition which could result in a freeze in the case of IrDA
communication or if used as UART, corrupted data.

Workaround is as follows for everytime MDR1 register is changed:
* setup all required UART registers
* setup MDR1.MODE_SELECT bit field
* Wait 5 L4 clk cycles + 5 UART functional clock cycles
* Clear the Tx and RX fifo using FCR register

Note: The following step is not done as I am assuming it is not
needed due to reconfiguration being done and there is no halted
operation perse.
* Read if required, the RESUME register to resume halted operation

Based on an earlier patch at:
http://git.omapzoom.org/?p=kernel/omap.git;a=commitdiff;h=42d4a342c009bd9727c100abc8a4bc3063c22f0cSigned-off-by: NDeepak K <deepak.k@ti.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

introduce silicon specific quirks as a errata handling mechanism

as a start UART_ERRATA_FIFO_FULL_ABORT is used to handle the override
for fifo full condition for rx and tx.
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Remove the following sparse warnings by declaring attr as static:
arch/arm/mach-omap2/serial.c:627:1: warning: symbol 'dev_attr_sleep_timeout'
was not declared. Should it be static?
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Initialization of pointer should be done with NULL. Removes sparse
warnings:
arch/arm/mach-omap2/serial.c:566:17: warning: Using plain integer as NULL pointer
arch/arm/mach-omap2/serial.c:567:17: warning: Using plain integer as NULL pointer
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Adds context save/restore for mcr register as state of mcr register
is lost after core off.
Signed-off-by: NGovindraj R <govindraj.raja@ti.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add initial support for the OMAP4 based Panda Board.
Signed-off-by: NDavid Anders <x0132446@ti.com>
[tony@atomide.com: selected board by default in Kconfig]
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds support for GPIO LEDs present on OMAP4
SDP and Blaze boards. This basically adds platform data
required by leds-gpio driver
Signed-off-by: NHemanth V <hemanthv@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Adding board configuration for the tmp105
temperature sensor. The interface to the sensor
is I2C.
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The MMC1 and MMC2 cards have seperate LDO supplies. Current code assumes
that they are powered by same LDO.

This patch fixes the same and has VAUX1 as supply to MMC2 card.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NSukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: NKishore Kadiyala <kishore.kadiyala@ti.com>
Tested-by: NKishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This commit will enable usage of tsl2563 ambient light sensor on Nokia N900.
Signed-off-by: NAmeya Palande <ameya.palande@nokia.com>
Signed-off-by: NMathias Nyman <mathias.nyman@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

With these and upcoming change to tpa6130a2 driver it's possible to add
support for the TPA6130A2 headphone amplifier.
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

There is REGULATOR_SUPPLY macro available for initializing the struct
regulator_consumer_supply so use it where applicable (all other supplies
than vdds_sdi) as it improves the readability.
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Acked-by: NEduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Proper operation of the tlv320aic3x audio codec requires that reset
sequencing is done in pair with supply voltages when using the regulator
framework. Add the codec reset gpio used in Nokia RX51 to tlv320aic3x
data.
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

It seems that the battery cover sensor in Nokia N900 is powered from the
V28 domain. Now if this regulator is disabled it causes that the gpio 160
reads only zero which effectively causes uSD removal detection.

Currently the bootloader enabled V28 is kept on but this may change in the
future according to comment in
drivers/regulator/core.c: regulator_has_full_constraints.

Also if there are any consumers on the V28 domain doing regulator_enable
regulator_disable cycle the V28 will be disabled after that.

Prepare for these by defining the V28 as always_on regulator.
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add platform data for NAND and wifi, also setup all GPIOs
needed to use the wifi chip.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Update gpio-keys setup so it matches what is on default firmware.
Also make use of debounce feature in gpio-keys instead of setting it
explicitly, as gpio-keys is now capable of using hardware debounce on
OMAPs thanks to recent gpiolib changes.
Also fix a sparce warning along the way.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add board muxing to support the wlan wl1271 chip that is
hardwired to mmc2 (third mmc controller) on the ZOOM3.
Signed-off-by: NOhad Ben-Cohen <ohadb@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add board muxing to support the wlan wl1271 chip that is
hardwired to mmc2 (third mmc controller) on the ZOOM2.
Signed-off-by: NOhad Ben-Cohen <ohadb@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Devkit8000 uses the TPS65930 and not the TWL4030.
The TPS65930 uses only a subset of the power supplies
of the TWL4030.
Signed-off-by: NThomas Weber <weber@corscience.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

omap_board_config is no longer used and thats why empty.
This patch removes the empty omap_board_config.
Signed-off-by: NThomas Weber <weber@corscience.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Using the macro gpio_is_valid for check of valid gpio pins.
Signed-off-by: NThomas Weber <weber@corscience.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Replacing supplies with the REGULATOR_SUPPLY macro.
Signed-off-by: NThomas Weber <weber@corscience.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

devkit8000_panel_enable_tv and devkit8000_panel_disable_tv are already
done in DSS2 code. So they are no longer needed in board code.
Signed-off-by: NThomas Weber <weber@corscience.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The Devkit8000 uses the cost reduced variant tps65930 of the twl4030.
The TPS65930 only has vdd1, vdd2, vpll1, vio, vmmc1, vdac and vaux2.

vaux2 is not used on Devkit8000.
Signed-off-by: NThomas Weber <weber@corscience.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The VDVI power supply is no longer needed in
board code with the new DSS2 interface.
Signed-off-by: NThomas Weber <weber@corscience.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch corrects the LCD reset pin configuration.

Original code from early devkit8000 patch sets the TWL4030 GPIO_1
to EHCI_nOC and TWL4030_GPIO_MAX+1 to ledA. Indeed these two pins
are both LCD_PWREN. Setup the lcd reset_gpio properly so it can be
disabled when other display is turned on.
Signed-off-by: NKan-Ru Chen <kanru@0xlab.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch corrects the DVI-D output setup of Devkit8000

Devkit8000 has different DVI reset pin with the BeagleBoard.
On Devkit8000 the TWL4030 GPIO_7 is assigned to do the job.
Signed-off-by: NKan-Ru Chen <kanru@0xlab.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Choose the generic panel for lcd code of Devkit8000.
Signed-off-by: NThomas Weber <weber@corscience.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Corrected the wrong power supplies in devkit8000 code.

Add supply for ads7846 to support the new regulator framework for
touchscreen.
Signed-off-by: NThomas Weber <weber@corscience.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

MACH_OMAP2_H4_USB1 doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: NChristoph Egger <siccegge@cs.fau.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

MACH_OMAP_H4_OTG doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: NChristoph Egger <siccegge@cs.fau.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

APM doesn't exist in Kconfig, therefore removing all references for it
from the source code.
Signed-off-by: NChristoph Egger <siccegge@cs.fau.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

LEDS_OMAP_DEBUG doesn't exist in Kconfig, therefore replacing all
references for it with OMAP_DEBUG_LEDS from the source code.
Signed-off-by: NChristoph Egger <siccegge@cs.fau.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

OMAP_STI doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: NChristoph Egger <siccegge@cs.fau.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

OMAP_DSP doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: NChristoph Egger <siccegge@cs.fau.de>
[tony@atomide.com: updated to apply on top of already queued patches]
Signed-off-by: NTony Lindgren <tony@atomide.com>

OMAP_IR doesn't exist in Kconfig, therefore removing all references
for it from the source code.
Signed-off-by: NChristoph Egger <siccegge@cs.fau.de>
[tony@atomide.com: updated for new mux code]
Signed-off-by: NTony Lindgren <tony@atomide.com>