This is to allow number of commands reserved for use by SCSI tape drives
and medium changers to be adjusted at driver load time via the kernel
parameter cciss_tape_cmds, with a default value of 6, and a range
of 2 - 16 inclusive.  Previously, the driver limited the number of
commands which could be queued to the SCSI half of the the driver
to only 2.  This is to fix the problem that if you had more than
two tape drives, you couldn't, for example, erase or rewind them all
at the same time.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

It causes NMIs which are undesirable at best, unsurvivable at worst.
Prefer the soft reset instead.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

Just go straight to the soft-reset method instead.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

on driver load, if reset_devices is set, and the hard reset
attempts fail, try to bring up the controller to the point that
a command can be sent, and send it a soft reset command, then
after the reset undo whatever driver initialization was done to get
it to the point to take a command, and re-do it after the reset.

This is to get kdump to work on all the "non-resettable" controllers
(except 64xx controllers which can't be reset due to the potentially
shared cache module.)
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

The bit-2-doorbell reset method seemed to cause (survivable) NMIs
on some systems and (unsurvivable) IOCK NMIs on some G7 servers.
Firmware guys implemented a new doorbell method to alleviate these
problems triggered by bit 5 of the doorbell register.  We want to
use it if it's available.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

Just to reduce the messages about timeouts that appear.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

When waiting for the board to become "not ready"
don't print a message saying "waiting for board to
become ready" (possibly followed by a message saying
"failed waiting for board to become not ready".  Instead,
it should be "waiting for board to reset" and "failed
waiting for board to reset."
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
"
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

Detect failure of controller reset by noticing if the 32 bytes of
"driver version" we store on the hardware in the config table
fail to get zeroed out.  Previously we noticed if the controller
did not transition to "simple mode", but this did not detect reset
failure if the controller was already in simple mode prior to
the reset attempt (e.g. due to module parameter hpsa_simple_mode=1).
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

This is to ensure the board interrupts are really off when
these functions return.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

After the anticipatory scheduler was dropped, there was no need to
special-case the request_module string. As such, drop the redundant
sprintf and stack variable.
Signed-off-by: NKees Cook <kees.cook@canonical.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

unplug is replaced with blk_run_queue now in blk_execute_rq_nowait,
so change the comment accordingly.
Signed-off-by: NTao Ma <boyu.mt@taobao.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

Disk event code automatically blocks events on excl write.  This is
primarily to avoid issuing polling commands while burning is in
progress.  This behavior doesn't fit other types of devices with
removeable media where polling commands don't have adverse side
effects and door locking usually doesn't exist.

This patch introduces new genhd flag which controls the auto-blocking
behavior and uses it to enable auto-blocking only on optical devices.

Note for stable: 2.6.38 and later only

Cc: stable@kernel.org
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NKay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

__blkdev_get() doesn't rescan partitions if disk->fops->open() fails,
which leads to ghost partition devices lingering after medimum removal
is known to both the kernel and userland.  The behavior also creates a
subtle inconsistency where O_NONBLOCK open, which doesn't fail even if
there's no medium, clears the ghots partitions, which is exploited to
work around the problem from userland.

Fix it by updating __blkdev_get() to issue partition rescan after
-ENOMEDIA too.

This was reported in the following bz.

 https://bugzilla.kernel.org/show_bug.cgi?id=13029

Note for stable: 2.6.38 and later only

Cc: stable@kernel.org
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NDavid Zeuthen <zeuthen@gmail.com>
Reported-by: NMartin Pitt <martin.pitt@ubuntu.com>
Reported-by: NKay Sievers <kay.sievers@vrfy.org>
Tested-by: NKay Sievers <kay.sievers@vrfy.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

cdrom_open() called check_disk_change() after the rest of open path
succeeded which leads to the following bizarre behavior.

* After media change, if the device opened without O_NONBLOCK,
  open_for_data() naturally fails with -ENOMEDIA and
  check_disk_change() is never called.  The media is known to be gone
  and the open failure makes it obvious to the userland but device
  invalidation never happens.

* But if the device is opened with O_NONBLOCK, all the checks are
  bypassed and cdrom_open() doesn't notice that the media is not there
  and check_disk_change() is called and invalidation happens.

There's nothing to be gained by avoiding calling check_disk_change()
on open failure.  Common cases end up calling check_disk_change()
anyway.  All we get is inconsistent behavior.

Fix it by moving check_disk_change() invocation to the top of
cdrom_open() so that it always gets called regardless of how the rest
of open proceeds.

Note for stable: 2.6.38 and later only

Cc: stable@kernel.org
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NAmit Shah <amit.shah@redhat.com>
Tested-by: NAmit Shah <amit.shah@redhat.com>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

* 'for-39-rc4' of git://codeaurora.org/quic/kernel/davidb/linux-msm:
  msm: timer: fix missing return value
  msm: Remove extraneous ffa device check

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: xen-kbdfront - fix mouse getting stuck after save/restore
  Input: estimate number of events per packet
  Input: evdev - indicate buffer overrun with SYN_DROPPED
  Input: document event types and codes and their intended use
  Input: add KEY_IMAGES specifically for AL Image Browser
  Input: twl4030_keypad - fix potential NULL dereference in twl4030_kp_probe()
  Input: h3600_ts - fix error handling at connect
  Input: twl4030_keypad - avoid potential NULL-pointer dereference

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  block: add blk_run_queue_async
  block: blk_delay_queue() should use kblockd workqueue
  md: fix up raid1/raid10 unplugging.
  md: incorporate new plugging into raid5.
  md: provide generic support for handling unplug callbacks.
  md - remove old plugging code.
  md/dm - remove remains of plug_fn callback.
  md: use new plugging interface for RAID IO.
  block: drop queue lock before calling __blk_run_queue() for kblockd punt
  Revert "block: add callback function for unplug notification"
  block: Enhance new plugging support to support general callbacks

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc/powermac: Build fix with SMP and CPU hotplug
  powerpc/perf_event: Skip updating kernel counters if register value shrinks
  powerpc: Don't write protect kernel text with CONFIG_DYNAMIC_FTRACE enabled
  powerpc: Fix oops if scan_dispatch_log is called too early
  powerpc/pseries: Use a kmem cache for DTL buffers
  powerpc/kexec: Fix regression causing compile failure on UP
  powerpc/85xx: disable Suspend support if SMP enabled
  powerpc/e500mc: Remove CPU_FTR_MAYBE_CAN_NAP/CPU_FTR_MAYBE_CAN_DOZE
  powerpc/book3e: Fix CPU feature handling on 64-bit e5500
  powerpc: Check device status before adding serial device
  powerpc/85xx: Don't add disabled PCIe devices

* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable: (24 commits)
  Btrfs: fix free space cache leak
  Btrfs: avoid taking the chunk_mutex in do_chunk_alloc
  Btrfs end_bio_extent_readpage should look for locked bits
  Btrfs: don't force chunk allocation in find_free_extent
  Btrfs: Check validity before setting an acl
  Btrfs: Fix incorrect inode nlink in btrfs_link()
  Btrfs: Check if btrfs_next_leaf() returns error in btrfs_real_readdir()
  Btrfs: Check if btrfs_next_leaf() returns error in btrfs_listxattr()
  Btrfs: make uncache_state unconditional
  btrfs: using cached extent_state in set/unlock combinations
  Btrfs: avoid taking the trans_mutex in btrfs_end_transaction
  Btrfs: fix subvolume mount by name problem when default mount subvolume is set
  fix user annotation in ioctl.c
  Btrfs: check for duplicate iov_base's when doing dio reads
  btrfs: properly handle overlapping areas in memmove_extent_buffer
  Btrfs: fix memory leaks in btrfs_new_inode()
  Btrfs: check for duplicate iov_base's when doing dio reads
  Btrfs: reuse the extent_map we found when calling btrfs_get_extent
  Btrfs: do not use async submit for small DIO io's
  Btrfs: don't split dio bios if we don't have to
  ...

Rather than pass in some random truncated offset to the pid-related
functions, check that the offset is in range up-front.

This is just cleanup, the previous commit fixed the real problem.

Cc: stable@kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

next_pidmap() just quietly accepted whatever 'last' pid that was passed
in, which is not all that safe when one of the users is /proc.

Admittedly the proc code should do some sanity checking on the range
(and that will be the next commit), but that doesn't mean that the
helper functions should just do that pidmap pointer arithmetic without
checking the range of its arguments.

So clamp 'last' to PID_MAX_LIMIT.  The fact that we then do "last+1"
doesn't really matter, the for-loop does check against the end of the
pidmap array properly (it's only the actual pointer arithmetic overflow
case we need to worry about, and going one bit beyond isn't going to
overflow).

[ Use PID_MAX_LIMIT rather than pid_max as per Eric Biederman ]
Reported-by: NTavis Ormandy <taviso@cmpxchg8b.com>
Analyzed-by: NRobert Święcki <robert@swiecki.net>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Mouse gets "stuck" after restore of PV guest but buttons are in working
condition.

If driver has been configured for ABS coordinates at start it will get
XENKBD_TYPE_POS events and then suddenly after restore it'll start getting
XENKBD_TYPE_MOTION events, that will be dropped later and they won't get
into user-space.

Regression was introduced by hunk 5 and 6 of
5ea5254aa0ad269cfbd2875c973ef25ab5b5e9db
("Input: xen-kbdfront - advertise either absolute or relative
coordinates").

Driver on restore should ask xen for request-abs-pointer again if it is
available. So restore parts that did it before 5ea5254.
Acked-by: NOlaf Hering <olaf@aepfle.de>
Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
[v1: Expanded the commit description]
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Calculate a default based on the number of ABS axes, REL axes,
and MT slots for the device during input device registration.
Signed-off-by: NJeff Brown <jeffbrown@android.com>
Reviewed-by: NHenrik Rydberg <rydberg@euromail.se>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The free space caching code was recently reworked to
cache all the pages it needed instead of using find_get_page everywhere.

One loop was missed though, so it ended up leaking pages.  This fixes
it to use our page array instead of find_get_page.
Signed-off-by: NChris Mason <chris.mason@oracle.com>

Instead of overloading __blk_run_queue to force an offload to kblockd
add a new blk_run_queue_async helper to do it explicitly.  I've kept
the blk_queue_stopped check for now, but I suspect it's not needed
as the check we do when the workqueue items runs should be enough.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

Reported-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

We just need to make sure that an unplug event wakes up the md
thread, which is exactly what mddev_check_plugged does.

Also remove some plug-related code that is no longer needed.
Signed-off-by: NNeilBrown <neilb@suse.de>

In raid5 plugging is used for 2 things:
 1/ collecting writes that require a bitmap update
 2/ collecting writes in the hope that we can create full
    stripes - or at least more-full.

We now release these different sets of stripes when plug_cnt
is zero.

Also in make_request, we call mddev_check_plug to hopefully increase
plug_cnt, and wake up the thread at the end if plugging wasn't
achieved for some reason.
Signed-off-by: NNeilBrown <neilb@suse.de>

When an md device adds a request to a queue, it can call
mddev_check_plugged.
If this succeeds then we know that the md thread will be woken up
shortly, and ->plug_cnt will be non-zero until then, so some
processing can be delayed.

If it fails, then no unplug callback is expected and the make_request
function needs to do whatever is required to make the request happen.
Signed-off-by: NNeilBrown <neilb@suse.de>

md has some plugging infrastructure for RAID5 to use because the
normal plugging infrastructure required a 'request_queue', and when
called from dm, RAID5 doesn't have one of those available.

This relied on the ->unplug_fn callback which doesn't exist any more.

So remove all of that code, both in md and raid5.  Subsequent patches
with restore the plugging functionality.
Signed-off-by: NNeilBrown <neilb@suse.de>

Now that unplugging is done differently, the unplug_fn callback is
never called, so it can be completely discarded.
Signed-off-by: NNeilBrown <neilb@suse.de>

md/raid submits a lot of IO from the various raid threads.
So adding start/finish plug calls to those so that some
plugging happens.
Signed-off-by: NNeilBrown <neilb@suse.de>